-
Product
Power Supplies
-
A power supply is an electrical device that supplies electric power to an electrical load. The main purpose of a power supply is to convert electric current from a source to the correct voltage, current, and frequency to power the load.
-
Product
L Band Splitter, DC Block All Ports
PD5182
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) Low PIM
-
Product
Frequency Meter, 3.7 to 12.5 GHz
537A
Frequency Counter
The Keysight 537A direct-reading frequency meter measures frequencies from 3.7 to 12.5 GHz quickly and accurately. Its long scale length and numerous calibration marks provide high resolution. This is particularly useful when measuring frequency differences or small frequency changes. Frequency is read directly in GHz so interpolation or charts are not required.
-
Product
Double Ridged Waveguide Horn
DRH203
-
Frequency range: 200 MHz - 3 GHz VSWR (max): < 1.6:1Impedance: 50 O (Ohm)Connector: N female Power (CW / Peak): 400 W / 750 W
-
Product
RTM Actuator Signal Conditioning Board
MS 3630I
-
CPCI Rear IO Actuator Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advanced Compute & IO Module (MS3639i). This board primarily focusing on Primary and Secondary actuator interface. This card shall handle excitation signals, conditioning, feedback measurement, power measurement. Card has high resolution Digital POTS, Direct Digital Frequency synthesizers, DAC, Discrete Input and Outputs, Analog measurement circuits for handling all sensor. All interface are brought to two 96 Pin Euro Connector.
-
Product
Adjustable Dipole Antenna
SNA600a
-
The SNA600 antenna is a versatile tool for use with wireless microphone receivers or IFB transmitters. The center frequency of its 100 MHz bandwidth is tunable from 550 to 800 MHz. The frequency is set by adjusting the dipole elements using the scale printed on the body of the antenna. The elements fold for storage.
-
Product
Handheld RF Spectrum Analyzer With 10MHz To 3.6 Or 6.0GHz Bandwidth Options
PSA Series 5
-
10MHz to 3600MHz or 6000MHz frequency rangeResolution bandwidths from 300Hz to 10MHz (1:3:10)-120dBm typical noise floor at -40dBm ref. level/10kHz RBWMeasurement in dBm or dBµV, mV or µWZero span mode with AM and FM audio demodulationTrace modes of normal, peak hold and trace averageLive, View and Reference traces in contrasting coloursTwin markers with readout of absolute & difference valuesSmart marker movement with selectable peak trackingFrequency counter with down to 10Hz resolutionFrequency presets and independent state storageAuto-find automatically sets sweep parameters for the highest signal foundUnlimited storage for waveforms, set-ups and screensUser assignable file names, file stamping from real-time clockUSB interfaces for Flash drives and PC connectionComprehensive status and context sensitive help screensRechargeable lithium ion battery giving more than 3 hours continuous operation from a chargeSmaller and lighter than other spectrum analyzers (weight only 0.56 kg)
-
Product
3.6 GS/sec Ultra Wideband RF/IF Rugged Rackmount Recorder
Talon RTR 2749
-
- Designed to operate under conditions of shock and vibration- Sample rates up to 3.6 GHz in single-channel mode- Sample rates up to 1.8 GHz in dual-channel mode- Capable of recording RF/IF frequencies to 1.75 GHz in single-channel mode- Capable of recording RF/IF frequencies to 2.8 GHz in dual-channel mode- 12-bit A/D, with 16- and 8-bit packing modes- Real-time aggregate recording rates of up to 4.8 GB/sec- 4U 19-inch rugged rackmount PC server chassis- Windows® workstation with high performance Intel® processor- Up to 122 terabytes of SSD storage to NTFS RAID solid state disk array- RAID levels 0, 5, and 6- SystemFlow® GUI with signal viewer analysis tool- C-callable API for integration of recorder into application- File headers include time stamping and recording parameters- Optional GPS time and position stamping- See Datasheet for configuration options for playback, recording and storage capacity
-
Product
Transducers and Probes
-
Olympus NDT probes and transducers are high-quality inspection equipment available in a range of frequencies, configurations, connection styles, and cable types. All our probes and transducers are lightweight but solidly constructed.
-
Product
GaN 100W Power Amplifiers
PE15A5033F
-
The PE15A5033F is a 100 W high gain Class A/AB Coaxial Linear Power Amplifier operating in the 0.7 to 2.7 GHz frequency range. The amplifier offers 100 Watts typical saturated power and 45 dB minimum small signal gain with 1.5 dB typical gain flatness @ Psat. The amplifier requires typically a +30V DC power supply. The SMA connectorized module is unconditionally stable and operates over the temperature range of 0C and +50C. The unit comes with a Heatsink and Fan.
-
Product
Hysteresis Loop Tracer
MESA
-
The MESA is the only hysteresis loop tracer on the market that can make measurements in the frequency range of 10 Hz and below. Competing units operate with more-easily generated 60 Hz drive fields, and can have errors of as much as 30% in coercivity (Hc) measurements.
-
Product
Suspension/Road Contact Tester
VLT3673-G6
-
The VLT 3673-G6 suspension / road contact testers operate according to the well-known EUSAMA principle. However, the diagnostic options are not restricted to the contents of this specification. In addition to the usual road contact values, the following values are also measured and displayed: the contact value difference, resonance frequency and wheel weight at minimum contact value, tyre rigidity, wheel weight and axle weight. There is a general final evaluation so that all these values do not have to be interpreted after every test.
-
Product
Kill A Watt PS-10
P4330
-
Now you can protect your valuable electronics and find out what they are actually costing you. Simply connect these appliances into the Kill A Watt® PS-10, and it will assess how efficient they are while the built-in surge protection keeps them safe. Advanced features such as over current, over voltage, and no load detection provide clean, safe power to your expensive equipment. Check the quality of your power by monitoring Voltage, Line Frequency, Amperage, KWH, Current Leakage and more. Now you’ll know how much power your entire computer or home theater system is using. With the innovative Kill A Watt PS-10 you’ll have peace of mind in more ways than one.
-
Product
HD Tablet/Touch Analyzer
BTPRO-8000S
-
Blonder Tongue Laboratories, Inc.
The BTPRO-8000S is a professional HD Tablet/Touch Analyzer with a frequency range of 4 to 2610 MHz. The analyzer features a 7-inch 16:9 color display touchscreen, is compact in size, and is lightweight.
-
Product
Single Photon Detector System For Near-Infrared (0.7 - 2.3 Um Wavelength)
-
*Frequency range includes coverage into higher frequencies than other photon counters on the market.*Short dead time (10 nanoseconds) compared to long dead time (microseconds) of alternatives. Therefore rapid repeition rate of 10s of MHz possible, whereas alternative have maximimum repetition rate of 1-10 kHz.*Very small dark counts (10/second) compared to high dark count (1,000s / second) of alternatives. Does not require gated mode unlike alternatives. Operates in continuous operation mode.
-
Product
Clamp-On Meters
-
Rugged and professional, our complete line of clamp-on meters offer full functions including: AAC, ADC, VAC, Ohms, Continuity, Frequency, Diode Test, TRMS, %THD, %DF, CF and Peak. Varying in size, our clamp-on meters provide a solution to all power quality measurement needs.
-
Product
AC Reference Modules
Reference Module
NAI offers a variety of AC reference modules that provide a drive capability to 5 VA. The units are transformer-isolated and operate over a frequency range from 47 Hz to 10 kHz. These modules are specifically designed for rugged defense, commercial aerospace, and industrial applications.
-
Product
USB Controlled High Precision Audio Test Interface
AudioConnect 4×4
-
AudioConnect 4×4 is a high accuracy 4-in, 4-out audio interface specifically audio test and measurement. It offers digital and analog audio in and out at any user-specified sampling rate up to 200kHz, and a high signal to noise ratio and wide frequency response, making it suitable for the most demanding measurement applications. Controls are simple – a single USB connection and a power indicator – all other typical soundcard controls that are not used for audio test applications have been eliminated to make operation and calibration simple with no room for error. AudioConnect 4×4 is supplied fully calibrated.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785167-01
FlexRio Digitizer
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
PXI RF Multiplexer, 10x SP4T, 1.3 GHz 75 Ω, SMB Connectors
40-755-310
Multiplexer Module
The 40-755-310 is a 10xSP4T 75 Ω multiplexer and is part of a range of high density RF multiplexers available in 50 Ω and 75 Ω variants with up to 10xSP4T switches in a single PXI module. They are available with two connector options; SMB that provides a frequency range of 1.8 GHz (50 Ω) / 1.3 GHz (75 Ω), or multiway which limits the bandwidth to 1.3 GHz but offers a high density solution occupying one PXI slot.
-
Product
Clamp Meter, True RMS, 100 A AC, 600 V AC, 600 V DC, 17 mm Jaw Opening Max.
72-2985
-
The 72-2985 from Tenma is a mini clamp meter in orange and grey colour. It features high reliability, safety precision and compact design. Its resolution ratio is 1mA, maximum range has maximum range of 100A AC/DC, particular VFC start mode. Entering this mode can accurately measure voltage and current which has VFC frequency conversion. Voltage or current response display is true valid value. Whole range overload protection, reliable measurement accuracy and unique appearance design makes it an outstanding new generation functional electrician/electric power measurement instrument. This complies with EN 610101-1, 61010-2-032, 61010-2-033, pollution degree 2, measurement category: (CAT II 600V, CAT III 300V) and double insulation standards. Conforms to UL STD. 61010-1, 61010-2-032, 61010-2-33 certified to CSA STD. C22.2 NO. 61010-1, IEC STD 61010-2-032, 61010-2-033.
-
Product
Antenna Tuner HF+6m
DU 800 T
-
The DU 800 T optimizes the performance of your antenna and transmitter or SWL receiver by providing adjustable impedance matching. The DU 800 T also measures the Power and Standing Wave Ratio (SWR), which allows you to tune the indiceted SWR to the lowestpossible ratio for the selected transmit frequency.
-
Product
Frequency Sensor
-
DARE?s frequency sensors and monitors are available in both AC powered and DC powered models in a wide variety of standard or custom enclosures. Used in aircraft, ground support equipment (GSE), ground power applications, and other military and industrial applications, DARE frequency sensors, monitors, and frequency sensing relays will protect equipment that is sensitive to fluctuations in power line frequency from damage due to over and / or under frequency conditions.
-
Product
Automatic Calibration Module
ACM4520
-
ACM4520 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 20 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process.
-
Product
Spectrum Analysis Up To And Beyond 125 GHz
S93094B
-
The S93094B has all of the capability of the S93090xA spectrum analyzer application with an upper frequency limit determined solely by the broadband or banded millimeter-wave frequency extenders used in the system.
-
Product
Line-impedance stabilisation network
NNB 21 set
-
The NNB 21 line impedance stabilization network is designed for measuring of grid bound interferences of a device under test according to the satndard CISPR 25/ISO 7637. It measures the RF interference, which couples into the vehicle electrical system. Measurements during the development in a frequency range from 100 kHz to 1GHz can be carried out.
-
Product
PXI Microwave Relay, Dual SPDT, 26.5GHz, 50Ω, SMA, External Termination
40-781A-322
Microwave Relay Module
The 40-781A-322 (PXI) and 42-781A-3221 (PXIe) are dual SPDT 26.5GHz microwave relay modules with external terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50GHz in 50Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
Heavy Duty Digital Multimeter
DMM 8007
-
1.999 count LCD display. Resistance to 2000 M£[. Frequency to 20MHz. Capacitance measurement. Inductance measurement. Logic Test. Transistor hFE test. Audible continuity test
-
Product
Impulse Sledge Hammer
-
Impact hammers are designed to measure the frequency of mechanical structures, such as mechanical movement, mechanical damping and impedance.
-
Product
2-18GHz Instantaneous Frequency Measurement Unit
DR058-F2
-
Teledyne Defence & Space’s Instantaneous Frequency Measurement (IFM) module, also known as a Digital Frequency Discriminator (DFD), offers high speed frequency measurement across the full operating bandwidth.The IFM measures the frequency of RF signal present at its input and presents a result at its output as digital data. The RF input signal is conditioned by an RF amplifier that provides sufficient drive for the frequency resolving circuits. The raw video from the resolvers is digitised and processed into the required output format. There is additional timing and control circuitry which initiates the measurement process and provides handshake data to the host system processor.
