Resistors
Keep a steady fixed or variable voltage to current ratio as measured in ohms.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-112
The 40-297A -112 (PXI) and the 42-297A-112 (PXIe) are 9-channel programmable resistors with a range of 1 Ω to 120 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI Precision Resistor Module 3-Channel, 2.5 to 102k
40-297-140
This 3-channel PXI Precision Resistor Module provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 series is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI 4-Channel Precision Resistor Card
50-297-102
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-022
The 40-297A-022 (PXI) and the 42-297A-022 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 1.81 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
Crowbar Resistors
Crowbar resistors are three phase resistance banks which are connected to the rotor windings of the DFIG (Doubly-Feed Induction Generator) such as wind power generator. They are used to prevent damage to the inverter circuits attached to rotor side when a fault occurs in the grid. DFIG power converter, which has a restricted over-current limit, needs special attention during faults in the grid. If the rotor current or DC link voltage reaches the threshold value, crowbar resistors disconnect the converter in order to prevent the generator turning into a squirrel cage induction machine. By crowbar resistors, the DFIG could stay connected to the grid and continue its operation.
-
product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 395kΩ
40-298-142
The 40-298-142 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PCI Precision Resistor Card 9-Channel, 2Ω To 13.6kΩ
50-297-031
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI Resistor Module 4-Channel 1R to 255R
40-293-013
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Precision Resistor Module 9-Channel, 1 to 31.5
40-297-110
The 40-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI 5W Programmable Resistor Module, 1-Channel, 2.5Ω to 773kΩ
40-252-043
The 40-252-043 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 773kΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI/PXIe High Density Precision Resistor Module, 18-Channel
40-297A-010
The 40-297A-010 (PXI) and the 42-297A-010 (PXIe) are 18-channel programmable resistors with a range of 1 Ω to 31 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PCI High Density Pecision Resistor Card, 4-Channel, 2.5Ω To 3.55kΩ
50-298-123
The 50-298-123 is a high density programmable resistor card with 4 channels which can be set between 2.5Ω and 3.55kΩ with 1Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-021
The 40-297A-021 (PXI) and the 42-297A-021 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 925 Ω. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-052
The 40-297A-052 (PXI) and the 42-297A-052 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 5.82 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 2Ω to 102kΩ
40-253-034
The 40-253-034 is a programmable resistor module with 1 channel which can be set between 2Ω and 102kΩ with 2Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Temperature Calibration
Process Instruments maintains primary temperature standards for the calibration of Standard Platinum Resistance Thermometers. SPRT''s are measured against a Thomas-type Ten Ohm Standard Resistor (a Leeds & Northrup 4211-B), using a Measurements International automated bridge. Primary thermometry points are maintained at the Water, Tin, Zinc and Gallium points.
-
product
PXI/PXIe High Density Precision Resistor Module
42-297A-031
The 40-297A-031 (PXI) and the 42-297A-031 (PXIe) are 9-channel programmable resistors with a range of 2 Ω to 13.6 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
SparkFun Soil Moisture Sensor (with Screw Terminals)
The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straightforward to use. The two large, exposed pads function as probes for the sensor, together acting as a variable resistor. The more water that is in the soil means the better the conductivity between the pads will be, resulting in a lower resistance and a higher SIG out. This version of the Soil Moisture Sensor includes a 3-pin screw pin terminal pre-soldered to the board for easy wiring and setup.
-
product
SparkFun Current Sensor Breakout
INA169
The INA169 is a “high-side current monitor,” which means that you place a resistor (a “shunt resistor”) on the positive power rail and the INA169 measures the voltage drop across that resistor. The INA169 outputs a small current based on the measured voltage drop. If you place a resistor from the output of the INA169 to ground, you can measure the voltage at the output.
-
product
PXI/PXIe 15W Programmable Resistor Module
42-254-113
The 40-254-113 (PXI) and 42-254-113 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 238Ω with 1Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
ELECTRICAL TEST Kit
1021 TK
Standard Electric Works Co., Ltd
2950 CL ● Pocket size.● 4000 counts.● Full automatic measurement : Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (auto off in 1 minute). ALS-2 ● Use with any clamp meter.● x10 mode allows for more accurate measurements of low amperage devices.● x1 mode allows for direct reading.● 4mm voltmeter input jacks.● Integrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.
-
product
PXI 2.5W Programmable Resistor Module, 2-Channel, 3Ω to 11.4MΩ
40-251-053
The 40-251-053 is a programmable resistor module with 2 channels which can be set between 3Ω and 11.4MΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 1.81kΩ
40-253-022
The 40-253-022 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 1.81kΩ with 0.5Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
RTD Simulator PCI Card 6-Channel PT1000
50-262-102
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card can provides a setting resolution of <90mΩ (also available in <8mΩ - PT100) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
product
SparkFun Decade Resistance Box
This is the SparkFun Decade Resistance Box, an involved PTH soldering kit that allows you to quickly and accurately dial in a specific resistance value between 0 and 999,990 Ω, in 10 Ω increments. The concept is simple, a decade box is a tool that contains resistors of many values that can be accessed via mechanical switches. All you need to do is just adjust the knobs to output any of the discrete resistances offered by the box. Once assembled, each kit will have controls that correspond to the digits in a decimal number - a control for the tens position, a control for the hundreds position, and so on.
-
product
PXI/PXIe 15W Programmable Resistor Module
40-254-115
The 40-254-115 (PXI) and 42-254-115 (PXIe) are programmable resistor modules with 1 channel which can be set between 1Ω and 920Ω with 4Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
product
Digital Circuit Breaker Analyzer
CT-7000 S3
The CT-7000 S3 is Vanguard’s fourth generation EHV circuit breaker analyzer. The CT-7000 S3 is available with 3 (part number 9021-UC) or 6 contact timing channels (part number 9100-UC). The CT-7000 S3 can fully analyze a circuit breaker’s performance by measuring the main contact and resistor contact time, stroke, velocity, over-travel, bounce back and contact wipes. Both contact and motion analysis can be performed on all circuit breaker operations (OPEN, CLOSE, OPEN-CLOSE, CLOSE-OPEN, and OPEN CLOSE-OPEN). The CT-7000 S3’s timing window is selectable between 1 second, 10 seconds, and 20 seconds.
-
product
PXIe High Voltage Programmable Resistor Module, REDEL Connector
42-230-355-HI
The 40-230-355-HI (PXI) and 42-230-355-HI (PXIe) are programmable resistor modules with 1 channel which can be set between 4.5Ω and 43.424MΩ with 4Ω resolution with maximum voltage of 1.2kV. The 40/42-230 range provides a simple solution for applications requiring voltage handling up to 1kV (9-pin D-type connector) or 1.2kV (22-pin REDEL connector).
-
product
Embedded Components
Teledyne Labtech prides itself in being at the forefront of RF/Microwave PCB development. Teledyne Labtech were also one of the first companies to successfully develop techniques for embedding SMD resistors and capacitors within multilayer structures and the embedding of connector pins in buried stripline circuits.The advantages of such a structures ensures a much higher density of interconnect. This then removes the need for via-hole connections to the board surface or the need to create access pockets to the inner layers. Consequently you finish with a board with that exhibits much lower RF/Microwave losses. This is particularly important when designing large RF feed networks or 16:1 power dividers.
-
product
PXI/PXIe High Density Precision Resistor Module, 6-Channel
40-297A-053
The 40-297A-053 (PXI) and the 42-297A-053 (PXIe) are 6-channel programmable resistors with a range of 3 Ω to 11.4 MΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
