-
Product
RH850 Family (Automotive Only)
-
The RH850 is Renesas Electronics' latest automotive micro-controller family that offers high performance balanced with very low power consumption over a wide and scalable range of products. This family offers rich functional safety and embedded security features needed for new and advanced automotive applications.
-
Product
Intelligent Sensors
-
Silicon Labs is a leading supplier of intelligent sensor solutions that are characterized by superb reliability, compact size, high levels of integration and unmatched ease of use for a variety of applications. Our diverse sensor product portfolio includes optical sensors, digital relative I2C humidity and temperature sensor ICs, biometric sensors and capacitive touch sense microcontroller devices.
-
Product
MAX31855 J-Type Thermocouple Sensor Breakout
SEN-30003-J
-
Breakout board for the MAX31855J digital thermocouple interface ICs by Maxim. Measured temperature range is -210C-1200C with known thermal characteristics and output resolution of 0.25C. This sensor supports a larger operating range (specifically in the negative range) than its predecessors, the MAX6674 and MAX6675, though it is not pin-pin compatible. This board is interfaced with a 0.1" 2x5 pin header (8-pins used), has four vertical mini thermocouple connectors and four mounting holes for standoffs and 4-40 screws. The SEN-30003 is interfaced via 3 or 4-wire SPI with a data-ready output for specific operating modes. An LDO and a high-speed level shifter are included to allow interfacing with microcontroller devices between 3.0V and 5V (all Arduinos, Raspberry PI, etc) without sacrificing device performance (many other level shifters reduce data rates to below 500 kHz).
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
Secure Wearable Solutions
-
From ST31 secure microcontrollers to ST54 solutions integrating NFC controller, secure element and eSIM, ST offers a complete range of solutions for payment, transit and multiple contactless services. ST's technology is ideal for applications that require a card emulation function but are environmentally challenged or have limited space for the antenna.
-
Product
Air-Cooled Universal Test Platform
Diamondx
-
Diamondx semiconductor test system extends Cohu’s low-cost, high-throughput production test solution platforms to high pin count, higher site count wireless, mobility, SOC, Flat Panel Display drivers, Power Management, and microcontrollers. Designed to meet the cost drivers IC companies face, Diamondx extends Cohu’s leadership in lowering the cost of operations.
-
Product
Circuit Simulation & PCB Design Software
TINA Design Suite
-
TINA Design Suite s a powerful yet affordable circuit simulation and PCB design software package for analyzing, designing, and real time testing of analog, digital, HDL, MCU, and mixed electronic circuits and their PCB layouts. You can also analyze SMPS, RF, communication, and optoelectronic circuits; generate and debug MCU code using the integrated flowchart tool; and test microcontroller applications in a mixed circuit environment.
-
Product
Cross Development Tools
68HC12 and HCS12
-
Cosmic's toolchain for the 68HC12/HCS12 family is part of a complete and uniform product line incorporating over 20 years of innovative design and development. Cosmic's familiar and easy to use software interface is available for all Freescale microcontrollers to simplify the migration between targets. All Cosmic products include one year of technical support and updates.
-
Product
Absolute Optical Inclinometer
A2T
-
The A2T is a single axis, digital gravity angle sensor. The A2T serves as a full 360 range absolute tilt sensing programmable level with either digital or analog output. Internally, a rotary bar coded disk is mounted to a weighted gravity driven wheel. A micro-controller strobes an LED to transfer the bar code image onto an optical linear array, then decodes the position every 2 mSec. Magnetic damping provides fast response and settling time while virtually eliminating overshoot and oscillations. An internal EEPROM stores field programmable parameters such as resolution, zero position, direction swap, and mode. This second generation design virtually eliminates the primary accuracy limitation of first generation inclinometers, which is sitation (hysteresis).
-
Product
Renesas Synergy™ Microcontrollers
-
Spanning across four distinct series, the Renesas Synergy™ Microcontroller family is designed for end applications ranging from connected mobile devices for the IoT market to high-performance embedded systems controllers.
-
Product
RFID Sensor Transponder (HF)
TELID®200
-
With the TELID® 200 range, you can have a combination of RFID transponders and sensors for measuring physical quantities. Here, in particular, pressure, acceleration, strain, moisture, and electric conductivity are of significant interest. Determining the situation just-in-time and storing the newly measured values in the integrated memory is one of its main functions. More complex functions such as digital I/O ports for connecting memories, microcontrollers and digital subsystems are also available. TELID® 200 products do not require batteries and work with no internal energy source.
-
Product
Board
Arduino Leonardo with Headers
-
The Arduino Leonardo is a microcontroller board based on the ATmega32u4 (datasheet). It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs), a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller; simply connect it to a computer with a USB cable or power it with a AC-to-DC adapter or battery to get started.
-
Product
Combination Board Tester
ATE QT2256-640 PXI
-
Qmax Test Technologies Pvt. Ltd.
Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or micro controller based boards. ATE QT2256-640 PXI system is designed as a combination board tester capable of testing highly complex and PCBs employing various techniques on a single platform. It can be easily upgraded to 640 digital channels and with programmable UUT power supplies, IEEE or PXI external instrumentation, Bus cycle signature system, ICE and integrated Boundary scan Test AC/DC parametric testing. The ATE is interfaced to an external host PC using a PCI express interface card allowing a maximum data transfer rate. Most commercial ATEs does only functional test and do not carry out DC/AC parameter testing, which are very essential in increasing the fault coverage and for achieving near zero field returns. The testing challenges get worse when the boards are equipped with BS compatible components, DSP chips and CPUs or microcontroller based boards.
-
Product
High Level Language Debugger and Emulator Tool
Universal Debug Engine
-
Programmierbare Logik & Systeme GmbH
With Universal Debug Engine (UDE®) PLS offers on top solutions for software development of systems-on-silicon including debug support for the 16 Bit and 32 Bit microcontrollers C16x, C166™, ST10F276, ST10F280, XC166, XC2000, XE166, XMC4500, C166S V2, SDA6000, TriCore™ from Infineon and STMicroelectronics, Power Architecture® MPC55xx, MPC560x, MPC563x, MPC57xx from NXP™, PowerPC PPC440SPe from AMCC, Power Architecture® SPC560, SPC563, SP574 from STMicroelectronics, ARM7™, ARM9™, ARM11™, Cortex™-M0, Cortex™-M0+, Cortex™-M3, Cortex™-M4, Cortex™-M7, Cortex™-R4, Cortex™-A8, Cortex™-A9, XScale™, SuperH™ SH-2A derivatives in a new multicore debug environment as well as technical support. The extensive feature list includes functions like: high speed and flexible target access via JTAG, cJTAG with OCDS L1, EmbeddedICE, OnCE, COP, DAP, DAP2, SWD support, OCDS L2 trace, MCDS trace, CoreSight™ trace, ETM trace, ETB trace, Nexus trace, ASC, SSC, 3Pin and CAN, in-system FLASH memory programming of FLASH / OTP with UDE MemTool, support of various RTOS, OSEK® and test automation tools.
-
Product
Low Cost Emulator
EB-XAG49
-
* Emulates P51XG49 Microcontrollers * Real-Time Operation up to 30MHz * 3.3V or 5V Voltage Operation * Source-Level Debugger for C and Assembler * MS-Windows Debugger Software * Reduced Set of C-Compiler and Assembler * Support for ROMless and ROMed Microcontrollers * 64K of Code Memory * Performance Analyzer * Real-Time and Conditional Breakpoints * 44-pin PLCC Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115 Kbaud
-
Product
ST10 16-bit Automotive MCUs
-
ST's ST10 microcontroller family offers a wide range of devices for use in automotive applications. The family integrates scalable single-voltage embedded Flash, from 128 to 832 Kbytes. Processed in 0.18 µm CMOS technology, it offers full 5 V capability and an internal on-chip voltage regulator.
-
Product
Cross Development Tools
S12X and XGATE
-
Cosmic Software's S12X and XGATE Development Tool Suite delivers the features and performance needed to create cutting edge applications. These tools are focused on leveraging the unique benefits of the S12X microcontroller family and XGATE module, while maintaining a standardized easy to use programming environment.
-
Product
Linear Equalizers
-
Macom Technology Solutions Holdings Inc.
MACOM offers high-performance linear equalizers for use in high speed copper connections for Ethernet, InfiniBand and Fibre Channel. The product line supports NRZ and PAM-4 multi-level signal connectivity and builds upon MACOM’s long-standing expertise in equalizers for broadcast video applications. The equalizers can support up to 112Gbps per lane data rates for 50 Gbps to 800 Gbps copper cable assemblies. In addition to copper cables, the linear equalizer can be used for wired backplane and on-board applications. Adding linear equalization to a passive copper cable can enable the same copper cable to carry higher data rates for longer distances. MACOM’s new linear equalizer product line can extend a typical copper cable’s performance to 7.5 meters at 56 Gbps and 5 meters at 112 Gbps data rates. Customers can consider active copper cables as an alternative to passive copper cables or active optical cables. Key benefits include low power consumption from a single 3.3V supply, low latency, hardware and microcontroller management modes. The products are suitable for SFP, QSFP, QSFP-DD and OSFP connector form factors.
-
Product
Evaluation Kits:
Grid-EYE® AMG8834EVAL Evaluation Kit
-
Panasonic Industrial Devices Sales Company of America
Panasonic is pleased to announce the availability of the Grid-EYE AMG8834EVAL Evaluation Kit featuring TrackMe Software for its' Grid-EYE Infrared Array Sensor, which integrates a ”nanopower” Bluetooth® Smart Module and a microcontroller. The AMG8834EVAL Kit is intended for prototyping the Grid-EYE Sensor which is a 64 pixel IR camera in a surface mount package measuring 11.6mm x 8mm x 4.3mm, which integrates the MEMS Sensor, lens and I2C interface.
-
Product
Multifunction Meters
-
Measures V, A, PF, Hz, KW, KVA, KVAr, Kwh, KVAh & KVArhTRMS MeasurementCan be used for Continuous MonitoringAuto / Manual Scroll Display (User Selectable)State of Art Microcontroller DesignPortable, Handy, Plug-n-Play and Easy-to-useLCD Display with BacklightRS-485 5KV Isolated Port (Optional) with MODBUS RTU Protocol (Optional)POWER MASTER Software for MIS Reports (Optional)
-
Product
SparkFun Qwiic Pro Micro
USB-C (ATmega32U4)
-
Here at SparkFun, we refuse to leave 'good enough' alone. That's why we're adding to our line-up of Arduino-compatible microcontrollers once more! The SparkFun Qwiic Pro Micro is a revision of the original Pro Micro and is, overall, functionally the same as the previous version. The board is the same size as the original Pro Micro but we added a few additional features by shrinking down some components on the board such as a reset button, Qwiic connector, USB-C, and castellated pads (this makes it really handy for you custom keyboard creators out there)! Think the Pro Mini except with an ATmega32U4 on board and full USB functionality.
-
Product
Distortion Detector PLUS
DD-1+
-
The purpose of this tool is to enable the installer to set the gain of an audio amplifier to match the source unit's output level, accurately and quickly. It can also be useful for detecting distortion in the audio signal caused by poorly designed or malfunctioning audio equipment. Sets audio system gain overlap, continuously variable from 0.0dB - 15.0dB in 0.1dB steps Checks gain overlap of an audio system without making any adjustments to the existing settings Verifies that the gain overlap of an install hasn't been tampered with after install Features our Patent Pending Distortion Detection system plus digital microcontroller and our proprietary firmware
-
Product
SparkFun ESP8266 Thing
Dev Board (with Headers)
-
This is the SparkFun ESP8266 Thing Dev Board --- a development board that has been solely designed around the ESP8266, with an integrated FTDI USB-to-Serial chip. The ESP8266 is a cost-effective and very capable WiFi-enabled microcontroller. Like any microcontroller, it can be programmed to blink LEDs, trigger relays, monitor sensors or automate coffee makers. With an integrated WiFi controller, the ESP8266 is a one-stop shop for almost any internet-connected project. To top it all off, the ESP8266 is incredibly easy to use; firmware can be developed in Arduino and uploaded over a simple serial interface. The ESP8266 Thing Development Board breaks out all of the module’s pins with pre-soldered headers, and the USB-to-serial converter means you don’t need any peripheral components to program the chip. Just plug in a USB cable, download the Arduino board definitions, and start IoT-ing.
-
Product
Analog
-
Create complete systems while streamlining your development process and reducing your design risk. We design our mixed-signal, linear, interface and power products for seamless integration with our extensive portfolio of microcontrollers, digital signal controllers, microprocessors and FPGAs.
-
Product
SparkFun Qwiic Quad Relay
-
The SparkFun Qwiic Quad Relay is a unique power accessory board that has been designed for switching not one but four high powered devices from your Arduino or another low powered microcontroller using I2C. Taking a look at the board, the Quad Relay has four individual relays rated up to 5 Amps per channel at 250VAC or 30VDC. Each channel also has its own uniquely colored LED, silk for easy identification, and screw terminals for optional connection. Utilizing our handy Qwiic system, no soldering is required to connect it to the rest of your system!
-
Product
Wireless Protocols for 2.4 GHz and Sub-GHz
Proprietary
-
Silicon Labs' proprietary wireless devices provide high-performance wireless connectivity and ultra-low power 8-bit and 32-bit microcontroller options. With support for major frequency bands in the 142 to 1050 MHz range and 2.4 GHz these devices can be used to develop many classes of Internet of Things (IoT) systems.
-
Product
Software Test Tool
testIDEA
-
The basic premise behind the development of testIDEA was simple: if our development tools have access to the source code and binary code of an embedded application, and our debug hardware can access all of the internal workings of the microcontroller, surely we can simply test embedded software on the target microcontroller.
-
Product
Microcontrollers
MCUs
-
Effortlessly meet the ever-changing requirements of modern electronics with our portfolio of scalable 8-bit, 16-bit and 32-bit microcontrollers (MCUs), Digital Signal Controllers (DSCs) and microprocessors (MPUs). Our flexible peripherals and functions make it easy to create differentiated applications that set you apart from your competition. You’ll find it simple to get started by using our intuitive design environments and visual configuration tools, while our proven reference designs and professionally-tested software libraries lower your design risk.
-
Product
Low pin and internal configurable analog MCU
RL78/G11
-
The RL78/G11 microcontroller line-up concept is based on small packages like 20 to 25pin, in small 16KB flash memory and rich analog peripherals such as A/D converters, D/A converters, comparators and PGA and these are configurable as PGA+ADC+VBGR, PGA+CMP, CMP+DAC/VBGR, or PGA+CMP+DAC/VBGR. Using the smart features like DTC and ELC a lot of peripherals can be connected internally to reduce CPU workload and can save overall power consumption. It also supports very low power operation (100 uA @ 1 MHz ) and a high speed 4µs wake up. Available in small 3x3mm² WFLGA , 4x4mm² HWQFN and standard 20pin LSSOP, this MCU line is suitable for sensor application, Lighting/power sources and many small appliances.
-
Product
Shield
Arduino MKR IMU Shield
-
The MKR IMU Shield is based on the BNO055 absolute orientation sensor from Bosch Sensortec GmbH which integrates a triaxial 14-bit accelerometer, a triaxial 16-bit gyroscope with a range of ±2000 degrees per second and a triaxial geomagnetic sensor with a 32-bit microcontroller running the BSX3.0 FusionLib software. The sensor features three-dimensional acceleration, yaw rate and magnetic field strength data each in 3 perpendicular axes.
