System Test
Testing conducted on a complete, integrated system to evaluate the system's compliance with its specified requirements .
See Also: Systems, Equipment, Test Systems, System Integrators
-
Product
120 A Manual Pulse Width Extender
TLP-12012A6
-
High Power Pulse Instruments GmbH
- Pulse width extender for the high current TLP/HMM test system TLP-12010A and TLP-12010C- 6 manual selectable pulse width: 5, 10, 50, 100, 200 and 500 ns- High pulse output current up to ±120 A- High performance and high quality components
-
Product
Software-based Electroacoustic Test System
SoundCheck
-
The SoundCheck®system from Listen includes everything you need to perform audio measurements on a wide range of devices – the software, the audio interface, other test interfaces and accessories, and test sequences.The system is centered around the SoundCheck software. This powerful package controls and communicates with the measurement hardware, and includes all the stimuli, algorithms and analysis functionality needed to develop and run virtually any electroacoustic or audio electronic test. It is paired with hardware ranging from a simple, all-in one audio test box to sophisticated discrete components for a complete test system. In addition to Listen hardware, a range of 3rd party products and test accessories are fully supported within SoundCheck.
-
Product
NI-9251, 3 Vrms, 102.4 kS/s/ch Simultaneous, 2-Channel C Series Voltage Input Module
783814-01
Voltage Input Module
3 Vrms, 102.4 kS/s/ch Simultaneous, 2-Channel C Series Voltage Input Module - The NI‑9251 with mini XLR is a low-distortion input channel that allows for the high dynamic range measurements necessary to fully test and evaluate modern audio outputs used in most consumer electronic devices. Unlike sound card-based solutions, you can quickly deploy the NI‑9251 to guarantee long-term measurement repeatability and increased test system uptime. To maximize low-noise benefits, the NI‑9251 differential input is provided through a mini‑XLR connector, which delivers a truly balanced input.
-
Product
PXI Programmable Resistor Card 2-Channel 3 Ohm to 65.5k Ohm - SPST
40-294-133
Programmable Resistor Modules
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Conformance Test System
TS-RRM
Test System
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 4.09k Ohm - SPST
50-294-123
Programmable Resistor Modules
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Motor Test for Electric Scooters
-
*The performance data of electric motors, in the majority of all cases, is performed by a brake test. Power input is calculated from current and voltage. Torque and power output are measured with a brake. It is important to reach, for each point, a persistent temperature. In case of large outer rotor BLDC motors, which are usually used for electric scooters, this traditional procedure may take many hours to complete, and is very complicated. *For several years, an innovative motor tester of MEA Testing Systems Ltd. is on the market. This testing system avoids any temperature confusion by testing a motor at constant temperature over the entire speed range. The test procedure is very fast, and gives the full load performances, including PWM current, voltage, torque, and driver efficiency, from stall up to no load. *During the test procedure, the motor is freely accelerated from stall to no load speed. The load of the motor is only the predetermined inertia of the rotor. From the moment of inertia and the acceleration, the torque of the motor is calculated and, also, the power output over the whole speed is given. Since the entire measuring time, depending on the motor size, is usually less than one second, the motor has no time to warm up. It remains at room temperature.
-
Product
Build to Print Services
-
Amfax are a Build to Print manufacturer with the production and quality processes necessary to service the demanding Aerospace, defence and commercial markets, but it is our extensive engineering and manufacturing expertise that really differentiates us. As a leading test system integrator and supplier, we are able to apply this expertise to your Build-to-Print projects.
-
Product
PXI Resistor Module 2-Channel 2R to 131k with SPDT
40-293-134
Programmable Resistor Modules
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Solenoid Test Systems
-
The production solenoid test systems are designed to check a high volume of parts each shift, verifying all important parameters of the solenoid.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 62.1Ω
40-251-111
Programmable Resistor Modules
The 40-251-111 is a programmable resistor module with 4 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Phoromatic
-
Phoromatic is a web-based remote management system developed for the Phoronix Test Suite. Phoromatic allows the automatic scheduling of tests, remote installation of new tests, and the management of multiple test systems all through an intuitive, easy-to-use web interface. Tests can be scheduled to automatically run on a routine basis across multiple test systems. The test results are then available from this central, secure location.
-
Product
DynoLAB Test Cell Supervisory System
-
SAKOR Technologies’ DynoLAB™ data acquisition and control systems offer reliable, cost effective automation of all types of dynamometer test systems. As with all SAKOR products, the DynoLAB system undergoes a continuous program of upgrade and improvement, regularly expanding and enhancing DynoLAB’s capabilities.
-
Product
Sequence Application Manager
AMFAX SAM
-
We have been building test systems for many years, as a result we find that many of the requirements our customers are looking for are very similar. This may be how a user logs in to the test system or the generation of test reports for example.
-
Product
Coaxial Matrix Switch, DC to 20 GHz
87406B
Matrix Switch Module
The Keysight 87406B matrix switch provides the life and reliability required for automated test and measurement, signal monitoring and routing applications. Innovative design and careful process control creates a switch that meets the requirements for highly repeatable switching elements in test instruments and switching interfaces. The switch is designed to operate for more than 10 million cycles and will meet all electrical specifications for at least 5 million cycles. The switch exhibits exceptional insertion loss repeatability. This reduces sources of random errors in the measurement path and improves measurement uncertainty. Switch life is a critical consideration in production test systems, satellite and antenna monitoring systems, and test instrumentation. The longevity of the switch increases system uptime, and lowers the cost of ownership by reducing calibration cycles and switch maintenance.
-
Product
Targets
-
Targets from group A are developed to support mostly testing infrared imaging systems understood as thermal imagers. These targets can be used also in testing visible/near infrared cameras or SWIR cameras but such application is not optimal. IR targets are mostly used in DT systems for testing thermal imagers and in MS systems for testing multi-spectral systems.
-
Product
T8090 Dual Absolute Leak Tester
-
The Dual Absolute.The new Dual Absolute technology makes it possible to eliminate the disadvantages of a classic differential system, improve its advantages and renew an industry that has been standing still for decades. Thanks to the new Dual Absolute technology, ForTest has combined the simplicity of a classic absolute decay system with the precision and sensitivity of a differential system, bringing leak testing instruments to a level never seen before.The new algorithms and measurement hardware eliminate typical defects in a differential system, such as differences in stabilization between the test part and the reference sample.The new range of instruments is able to work in 3 different ways: Pure Differential, Dual Absolute and Central Zero.The new Dual Absolute technology is so powerful and reliable that ForTest has decided to stop developing the classic differential system.
-
Product
Radiated Immunity Test System
-
Beijing KeHuan Century EMC Technology Co,.LTD
Radiation Immunity Test System.
-
Product
Inductive Sensor
HFCT Ø 30-39-50mm
-
Techimp HFCT is an inductive sensor for partial discharge measurements. It is suitable for on/off line PD tests on many electrical systems (cables, transformers, rotating machine, etc..). It has to be applied to the ground connection of the system to be tested.
-
Product
In-Circuit Tester
Sigma MTS300
-
The system is designed for high throughput; with up to 1,000 analog measurements per second it is one of the fastest test systems available on the market. Sigma test systems provide analog and digital In-Circuit Test capabilities, Vectorless Testing, Functional Test, Boundary Scan and On-Board Programming.
-
Product
PXI Thermocouple Simulators
-
Our PXI Millivolt Thermocouple Simulator modules provide 32, 24, 16 or 8 channels of accurate low sources. They are ideal for the simulation of thermocouples and can be used for sensor emulation in ECU testing. The channels can be operated with one of three voltage ranges covering most thermocouple types. We can also supply connection solutions allowing the easy integration of the Thermocouple Simulator into your test system.
-
Product
PCI Precision Resistor Card 4-Channel, 2Ω To 26.7kΩ
50-297-132
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Automated Switch Test Equipment
-
TRICOR Systems Inc. offers test equipment for switches, keypads, rubber, etc. Virtually any component where accurate force-displacement and measurements are required. From our Model 933A, a low cost life test system to our Model 925 test station used to obtain precise force measurements relative to displacement; we have the system you require.
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 1Ω to 239Ω
40-251-113
Programmable Resistor Modules
The 40-251-113 is a programmable resistor module with 4 channels which can be set between 1Ω and 239Ω with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
SR/QE Testing System
PVE300
-
Industrial Vision Technology Pte Ltd.
Solar Cell Multi-function SR/QE Testing System is specially designed for Photovoltaic Industry to characterize the Optical Performance of Raw material, process wafer, finished solar cell, as well as small Module.
-
Product
Protection Relay Testing
ARTES
-
Compact, powerful relay test systems for carrying out highly complex tests with ease and precision. The test systems of the ARTES product line are used to carry out functional tests on all types of protection devices, including DT/IDMT relays, distance protection relays and differential protection relays, to ensure that they function correctly. More than 20 years of experience in developing and manufacturing automatic relay test systems have gone into creating the fourth generation of ARTES test instruments.
-
Product
Power Quality Monitoring Terminal Detection Platform
PQC1650
-
PQC1650 power quality terminal detection platform is a test system specially designed for power quality terminals. It can fully complete the power quality test method and accuracy test of power quality terminals.
-
Product
PXI 5W Programmable Resistor Module, 1-Channel, 2.5Ω to 201kΩ
40-252-041
Programmable Resistor Modules
The 40-252-041 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 201kΩ with 0.25Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Electromagnetic Vibration Testing Systems
EV series
-
Labtone Test Equipment Co., LTD
EV series of electromagnetic vibration testing systems cover a wide range of forces ideal for many different applications. The electrodynamic shaker systems are well-suited for vibration testing products and structures of any size – from small components and electronic hardware to very large devices and structures.
-
Product
PXI 2.5W Programmable Resistor Module, 2-Channel, 2.5Ω to 773kΩ
40-251-043
Programmable Resistor Modules
The 40-251-043 is a programmable resistor module with 2 channesl which can be set between 2.5Ω and 773kΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
