Rf Switches
-
product
PXI 9 x SPDT RF Switch 500MHz 50 Multiway Connectors
40-754-009
The 40-754 is a 50Ω High Density RF switch available with 17 or 9 SPDT relays in a single PXI module. The 40-754 is available with two connector options; an SMB connector that provides a frequency range of 1.2GHz (useable to 1.8GHz) occupying two PXI slots, or an MS-M RF multiway connector which limits the bandwidth to 500MHz but offers a high density solution occupying one PXI slot. The RF switch design is identical in each case.
-
product
PXI Triple SPDT RF Switch 3GHz 50 SMB
40-870-003
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
product
RF Matrix Switch for Wireless Technologies up to 4 GHz
NEXUS-4
Quintech Electronics and Communications Inc.
The NEXUS-4 is a bi-directional fully non-blocking 3232 RF matrix switching system that can route any input ports to any outputs in a 6 RU chassis. With the frequency range of 700 MHz to 4 GHz and the capability of expanding to 256256, it enables large scale wireless testing that involves many MIMO base stations and devices. The built-in programmable attenuators and efficient automation interface provide ease-of-use testing of signal fade and emulation of mobility scenarios. It can dramatically increase lab efficiency by eliminating manual patch panel and cabling as it can be remotely reconfigured for different test setups consistently in seconds.
-
product
PXI Triple SPDT RF Switch MCX 75 Ohm
40-830-103
The 40-830 is a 75 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks have been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40-830 minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
product
Computer Controlled, Solid-State RF Switch Matrices
PMI offers a full product line of RF Switch Matrices that operate over the 20MHz to 40GHz frequency range. Three standard models are offered that cover this frequency range, namely 20MHz to 3.0GHz, 2.0GHz to 18.0GHz, and 18.0GHz to 40.0GHz. Any of the three models can be supplied as either a 4 X 4, 8 X 8, 16 X 16, or 32 X 32 non-blocking matrix.
-
product
LXI Mainframes
The EX1200 family is the highest density switch and data acquisition instrument on the market with the ability to mix low-level, power, and RF switch modules in a single mainframe. This scalable family of products is designed to leverage capital investments in one common hardware and software platform that can be used in development, manufacturing, and field service. Mix and match a variety of modules to build a comprehensive signal switching subsystem that can be supplemented with precision analog and digital I/O modules.
-
product
LXI 1GHz 75ohm 24x4 Matrix
60-732-002
The 60-732 is a family of integrated RF matrices suitable for use up to 1.5GHz. The construction of the 60-732 provides a cost effective alternative for RF switching based on microwave switching elements while maintaining a high level of matrix performance. The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family.
-
product
RF Switch Matrix
Switch Matrices are offered in Blocking, Non-Blocking, and Super Non-Blocking configurations in mechanical housing packages of 1U-10U. Completely customizable control (USB, 10/100 Base-T) and expandable in blocks of 8 by 8 and 64 by 64 in a single unit, multiple units up to 256 by 256.
-
product
Upstream Analyzer
Upstream Analyzer is a web-based application that displays the return path spectrum from your CMTS in real time from anywhere. There’s no expensive upstream spectrum analyzer or headend equipment to buy, no cabling, no splitters or connectors to hassle with. That’s right. No changes in your combining plant or RF Switches needed. All you need is your CMTS and Upstream Analyzer and your staff can view the upstream spectrum from your CMTS wherever they happen to be, whether that’s at their desk or in the field.
-
product
LXI 1GHz 75ohm 8x8 Matrix
60-731-004
The 60-731 is a family of integrated RF matrices suitable for use up to 1.5GHz. The construction of the 60-731 provides a cost effective alternative for RF switching based on microwave switching elements while maintaining a high level of matrix performance. The design is fully scalable, allowing a variety of matrix sizes to be offered in a single family.
-
product
2 X 1 RF Switch
MX 1×2 RF
Auto detect 2×1 RF switch, used for simple automated switching or redundancy of the RF signal path.
-
product
PXI/PXIe RF Switch, Octal SPDT, Terminated, 8GHz, 50Ω, SMA
42-880B-004
The 40-880B-004 (PXI) and 42-880B-004 are octal SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range have automatic termination of unused signals and are available as a dual switch in a 1-slot, a quad switch in 2-slots or hex and octal switches in 3-slots.
-
product
PXI-2557, 2.5 GHz, 75 Ω, 8x1 PXI RF Multiplexer Switch Module
778572-57
2.5 GHz, 75 Ω, 8x1 PXI RF Multiplexer Switch Module—The PXI‑2557 is an RF signal multiplexer switch module. The higher channel count of the PXI‑2557 makes it ideal for test systems that require the switching of a large number of video RF signals, such as switching several video tuners under test to a single channel on the RF analyzer. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
PXI/PXIe RF Switch, Hex SPDT, 3GHz, 50Ω, MCX
40-870A-106
The 40-870A-106 (PXI) and 42-870A-106 (PXIe) are 50Ω RF switches with 6 separate SPDT relays in a single slot. They have low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40/42-870A has been minimized by careful attention to the mechanical and electrical design.
-
product
Solid State RF and Microwave Switches
The Solid State RF and Microwave Switches have the following advantages over mechanical switches; long operating life, fast switching time, low power consumption and small size. Mechanical RF and Microwave Switches usually have lower insertion loss, higher isolation and higher RF power handling capability. However, because of the advantages mentioned above, Solid State RF and Microwave Switches are to prefer if very low insertion loss and/or very high isolation is not needed.
-
product
RF POWER AMPLIFIERS
BLWA Series
A) RF-Sample Ports I) 3x 208 V AC / 60 HzB) External Dual Directional Coupler L) LAN Remote ControlC) IEEE-488.2 GPIB Remote Control S) Internal RF Switching UnitD) Front Panel RF Connectors R) RS-232C Remote ControlE) RF Power Indication (digital) U) USB Remote ControlF) Gain Adjustment W) Liquid CoolingH) DC Supply X) External Control of other Amplifiers
-
product
RF Switch
RF switches are components used for switching the signal paths of high frequency circuits in wireless communication devices.
-
product
PXI/PXIe RF Switch, Hex SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-003
The 40-880B-003 (PXI) and 42-880B-003 (PXIe) are hex SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range have automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in slots or hex and octal switches in three slots.
-
product
RF PXI Matrix Modules
Pickering's RF PXI Matrix Modules are capable of providing economic switching for frequencies up to 6 GHz. Our other RF PXI options include RF SPDT switches and RF multiplexers, for higher frequency applications or applications requiring high-performance levels, please take a look at our microwave switching modules.
-
product
SP1T RF Pin Diode Switches To 18 GHz
Pulsar Microwave manufactures pin diode RF switches that are controlled by TTL logic. This configuration is known as single pole, single throw and is often abbreviated SPST or SP1T. They have been engineered to function in 50-ohm systems, and are designed to operate from 40 MHz to 18 GHz. They have a switching time of 100 nanoseconds and input power rating of 200 mW (23 dBm). Performance of 1.6:1 or better VSWR and minimum isolation of 60 dB is typical of most models.All switches of this type require both +5VDC and -5VDC to operate. Typical current consumption is +/- 30 mA. TTL control logic of 0 to +5VDC is required. Units comes standard with SMA connectors.
-
product
PXI RF Multiplexer Modules
Pickering's PXI RF Multiplexer Modules are capable of providing economic switching for frequencies up to 6 GHz. They are available in 50 and 75, the 75 version are designed for Telecoms and high quality video switching. Our other PXI RF options include RF SPDT switches and RF matrices. For higher frequency applications or applications requiring high performance levels, please take a look at our Microwave Switching Modules.
-
product
PXI/PXIe RF Switch, Octal SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-004
The 40-880B-004 (PXI) and 42-880B-004 are octal SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range have automatic termination of unused signals and are available as a dual switch in a 1-slot, a quad switch in 2-slots or hex and octal switches in 3-slots.
-
product
PXI/PXIe RF Multiplexer, Dual 6-Channel, Terminated, 8GHz, 50Ω, SMA
42-881B-002
The 40/42-881B has low VSWR characteristic over the full operating frequency range and consistent insertion loss characteristics. The use of solid state switches ensure a long service life with no wear out mechanism, making the module ideal for ATE systems requiring frequent and fast operating RF switching with no contact bounce.
-
product
RF Microwave Switch Matrices
RF Microwave Switch Matrices provide automatic routing of RF microwave signals between test instrumentation and the unit under test (UUT). They provide consistent signal paths, enable automation of tests, and often include signal conditioning.
-
product
PXI-2595, 5 GHz, 50 Ω, 4x1 PXI RF Multiplexer Switch Module
778572-95
5 GHz, 50 Ω, 4x1 PXI RF Multiplexer Switch Module—The PXI‑2595 is ideal for applications that require the routing of high-frequency signals inside automated test equipment (ATE) systems because it can switch signals with very low insertion loss. The module also features excellent insertion loss, voltage standing wave ratio (VSWR), and isolation parameters to minimize signal degradation. You can use the onboard relay count tracking feature to predict relay lifetime and reduce unexpected system downtime.
-
product
PXIe-254, 6.6 GHz, 50 Ω, Solid-State, Dual 4x1 PXI RF Multiplexer Switch Module
780587-43
PXIe, 6.6 GHz, 50 Ω, Solid-State, Dual 4x1 PXI RF Multiplexer Switch Module—The PXIe‑2543 features high-performance solid-state relays that offer unique benefits such as unlimited relay life and fast switching time. Front-mounted SMA connectors provide easy connection to your RF devices, and the module features termination on every COM line and channel.
-
product
PXI Triple Microwave SPDT Relay 50GHz 50 SMA-2.4
40-780A-553
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
-
product
PXI RF Matrix Switch Module
PXI RF Matrix Switch Modules are organized into rows and columns and provide maximum flexibility for switching systems by allowing you to connect any channel to any other channel. PXI RF Matrix Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor (FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a matrix that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NI Switch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
product
RF Switches
Teledyne e2v Hi-Rel RF switches feature high linearity, isolation and exceptionally rugged performance for space applications.
-
product
PXI Single Microwave SPDT Relay 18GHz 50 SMA
40-780A-521
This PXI microwave module is part of a range that gives you the highest RF & microwave switching performance available. Applications are mainly in the microwave region, however there are many uses in the RF spectrum where extremely low insertion loss and ultra high isolation are critical, they may also be used for lower frequency RF applications where power handling to 240W is required (700W for N-Type options).
