FPGA Modules
-
Product
PXI Single 36 Channel MUX, SMB Connectors
40-735-912-S4
Multiplexer Module
The 40-735 data communications multiplexer is designed for switching the data lines of serial interfaces (RS232, USB). Careful attention to the design of the module ensures that the switching system minimizes its impact on the transmission distance of USB1.1 interfaces. The MUX is available in 36:1 or 18:1 formats and enables a single source of serial data to be switched to one of 36 or 18 devices under test. This allows the data source to load information to, or receive information from, the device under test. This 36:1 version can be software configured into two independent 18 way MUXs enabling two separate sources of serial data to be connected to separate banks of 18 devices. The module is ideal for performing bulk testing of any device that relies on a serial data communications port to load software or control the device operation. It can also be used for a variety of other applications where ever a 2-pole low power MUX is required.
-
Product
LXI High Voltage Switching - 2-Bank, 1-Pole, 24:1 Multiplexer Plugin Module
65-231-903
Multiplexer Module
The 65-231-903 plug-in module is part of a scalable high voltage multiplexer platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 18 GHz, 50 Ω, SMA, Terminated, Failsafe
42-785C-422-T
Multiplexer Module
The 40-785C-422-T (PXI) and 42-785C-422-T (PXIe) are dual failsafe SP4T 18 GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available in single or dual, SP6T or SP4T configurations with relays mounted on the front panel. Remote versions are also available which can support up to three multiplexers in a single slot.
-
Product
Signal, Module, ID, CASS, QuadraPaddle, 800 Position
510114131
ITA Module
Signal, Module, ID, CASS, QuadraPaddle, 800 Position.Mating module is 510113138.
-
Product
High Performance Autoranging DC Power Module, 50V, 5A, 50W
N6751A
Power Module
The Keysight N6751A is a 50 W high-performance, autoranging DC power module that provides low noise, high accuracy and programming speeds that are up to 10 to 50 times faster than other programmable power supplies. Optional high-speed test extension offers an oscilloscope-like digitizer that increases measurement accuracy when viewing high-speed transient or pulse events within the device-under-test (DUT).
-
Product
PXI High Density MUX BRIC, 8-Chan, 40-Pole
40-570-212
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP6T, 18GHz, 50Ω, SMA, Terminated
40-785C-522-T
Multiplexer Module
The 40-785C-522-T (PXI) and 42-785C-522-T (PXIe) are dual SP6T 18GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
96-Ch SPST 2A-250VAC 24VDC Switching
YAV90064
Switch Module
96 relays SPST, 2ASwitching 2A 250Vac. Up to 62.5VACAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 10-Bank 40GHz SMA-2.9
60-801-410
Multiplexer Module
The 60-801-410 is a 6-channel, 10-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI Breadboard Module, 1Slot, Dual 20-Pin GMCT
40-220A-811
Signal Module
The 40-220A series of breadboard modules allow the user to construct their own circuit in situations where a suitable PXI module is not available. For example when it is required to integrate a non-switching function into a PXI chassis. Typical applications include: Creating custom circuitry that can be housed in on a 3U board, or to build special one-off switching modules.
-
Product
PXI 10A Power Multiplexer, 8-Bank, 4-Channel (SP4T)
40-661A-001
Multiplexer Module
The 40-661A-001 is a single pole, 8-bank, 4-channel (SP4T) PXI power multiplexer module, suitable for switching inductive/capacitive loads up to 10A with 125VDC/250VAC hot switching and 400VDC/250VAC cold switching. The multiplexer is available in 8-bank 4-channel, 5-bank 6-channel, 4-bank 8-channel, 2-bank 16-channel and 1-bank 32-channel formats. Also, 4-bank 4-channel, 2-bank 8-channel and 1-bank 16-channel half density configurations are available.
-
Product
Quad 4 to 1 50 600MHz PXI RF Multiplexer
40-760-004
Multiplexer Module
This 4 to 1 multiplexer is part of a range of RF multiplexers available in the following configurations: dual, quad and octal 4 to 1, single, dual and quad 8 to 1, single and dual 16 to 1 and single 32 to 1. All multiplexers have the option of automatic terminations which offer advantages at system level by reducing the presence of standing waves in the system which can cause degradation in isolation and crosstalk.
-
Product
6U Power Supply Mainframe. Accepts Two Programmable Power Modules
GX7400A
Power Module
The GX7400A is a dual output programmable DC power supply designed for use in 6U PXI systems. The GX7400A occupies three slots and is controlled via the PXI bus. The AC power is provided using a panel-mounted receptacle. The power supplies are fully isolated and can be externally connected in series to provide higher voltage.
-
Product
PXI/PXIe RF Multiplexer, Single 4-Channel, 3GHz, 75Ω, SMB
42-832A-001
Multiplexer Module
The 40-832A-001 (PXI) and 42-832A-001 are 75 Ohm 4 to 1 RF multiplexers with 1 bank in a single slot. They have been designed to exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. Each MUX has been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz with each path having a nominally equal insertion loss. The design of the 40/42-832A minimizes the injection of noise and unwanted signals into the signal path by careful attention to the mechanical and electrical design.
-
Product
PXI 8-slot BRIC Multiplexer, 4-Channel, 160-Pole (6 Sub-cards)
40-570A-014
Multiplexer Module
The 40-570A-014 is a 4-channel, 160-pole High-Density Multiplexer and is part of our BRIC family. The 40-570A range is designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing.
-
Product
PXI Multiplexer Single 48 Ch 1 Pole
40-632-021-48/1
Multiplexer Module
This series of general purpose multiplexer modules feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems. Connections are made via a front panel 68-pin connector. Available reed relay formats are 1-pole, 2-pole and 1-pole screened.
-
Product
PXI 12 Channel High Voltage Multiplexer
40-320-001
Multiplexer Module
The 40-310/320 Range of High Voltage Switching Modules will hot switch up to 750V peak and cold switch up to 1000V peak in either general purpose relay (40-310) or multiplexer (40-320) configurations. These modules contain high-quality reed relays with switching ratings comfortably higher than the 40-310/320 specification. Applications for the 40-310/320 series modules include; circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
sbRIO-9860, Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module
787325-01
Interface Module
Non-Enclosed, 2-Port, C Series Vehicle Multiprotocol Interface Module - The sbRIO-9860 is a hardware-selectable HS/FD controller area network (CAN) and/or local interconnect network (LIN) interface for developing CAN and/or LIN applications. As part of the NI-XNET product line, the sbRIO-9860 works well for applications requiring high-speed manipulation of hundreds of frames and signals while performing low-level FPGA control and embedded monitoring in the same CompactRIO Single‐Board Controller. Non-enclosed modules are available for OEM applications.
-
Product
Switch Modules - 16 Single Pole Relays Arranged as an 8x2 Matrix
JX16/AB-1
Switch Module
This module has 16 single pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 matrix. It is available with Type S or M reed relays for high speed, long life application. These modules are usually used for 2 wire testing where high and low meter leads must be switched between any two points. Often used for 2 wire LCR meter measurements, cable testing, or open / short testing in a variety of applications.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 4-Bank 40GHz SMA-2.9
60-801-404
Multiplexer Module
The 60-801-404 is a 6-channel, 4-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 11-Bank 26.5GHz SMA
60-802-311
Multiplexer Module
The 60-802-311 is a 4-channel, 11-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
PXI Fault Insertion Switch, 6-channel, Two Fault Buses, 10 A
40-192A-012
Switch Module
The 40-192A-012 is a PXI fault insertion switch using solid state switching elements and is capable of switching current up to 10A. It is designed to be able to insert three different fault conditions between the test fixture and the equipment under test
-
Product
Quad 2-Channel 1-Pole 16 Amp PXI Power Multiplexer
40-662-011
Multiplexer Module
The 40-662 range of 16 Amp PXI power multiplexer modules is available in seven configurations ranging from 4-off 2:1 multiplexers to 1-off 16:1 multiplexer. Power multiplexer modules are intended for switching heavy AC or DC loads or for the slave switching of large external relays, contactors and solenoids. All versions are suitable for switching loads up to 16 Amp at 250VAC. User connections are made via a 20-way GMCT plug which is fully support by our comprehensive range of cables and connector accessories.
-
Product
VTAC, Module, ITA, iCon Series, 128 Pos, 16 Slot
510161130
ITA Module
This iCon module is compatible with iCon, i1, D1 and D3/D4 ITAs. Contains slots for 16 VTAC inserts, in 2 rows of 8. NOTE: Not cross-compatible with previous rev model 14 slot VTAC iCon module.Primary mating module 510160130.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP10T, 8 GHz, 50 Ω, N-Type, Remote Mount, Failsafe
42-788-112-E
Multiplexer Module
The 40-788-112-E (PXI) and 42-788-112-E (PXIe) are dual failsafe SP10T 8 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-788 range of multiplexers are also available as single or dual, SP8T, SP10T or SP12T panel mounted multiplexers with relays mounted on the front panel.
-
Product
PXI-6683, TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module
782110-01
Synchronization Module
TCXO, GPS, IRIG-B, IEEE 1588 PXI Synchronization Module—The PXI‑6683 timing and synchronization modules synchronize PXI and PXI Express systems using GPS, IEEE 1588, and IRIG‑B to perform synchronous events. The PXI‑6683 can generate events and clock signals at specified synchronized future times and timestamp input events with the synchronized system time. The PXI‑6683 features an onboard temperature-compensated crystal oscillator (TCXO) that can be disciplined to GPS, IEEE 1588, and IRIG‑B for long-term stability. You also can use the PXI‑6683 to route clock signals and triggers with low skew within a PXI chassis or between multiple chassis, providing you a method for synchronizing multiple devices in a PXI system.
-
Product
PXI Monitored Multiplexer, Dual 16-Channel, 1-Pole
40-619-002
Multiplexer Module
The 40-619-002 is a high density PXI 2 A multiplexer module in dual 16-channel configuration using high quality electro-mechanical signal relays allowing each channel to switch current up to 2 A and voltage up to 250 VAC/DC.
-
Product
Load Board
cPCI 3U
Load Module
Load boards are essential in keeping any system in top running shape. As a full-system provider, Hartmann strives to not only provide the systems you need, but the supporting hardware as well.
-
Product
PXI/PXIe Microwave Multiplexer, Triple SP6T, 40 GHz, 50 Ω, SMA-2.9, Remote Mount, Failsafe
42-784B-043-E
Multiplexer Module
The 40-784B-043-E (PXI) and 42-784B-043-E (PXIe) are triple failsafe SP6T 40 GHz unterminated microwave multiplexers with remotely mounted relays. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI High Density MUX BRIC, 4-Chan, 40-Pole
40-570-211
Multiplexer Module
This range of High-Density Multiplexer is part of our BRIC family. These MUX's are designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is also possible, without limitation). These multiplexers are ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. They are available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts. All version are supported in a BRIC8 construction that occupies eight PXI 3U mechanical slots, one of which provides the PXI interface and power.
