-
Product
Wire Harness Tester
NX Solo
-
The Dynalab NX Solo Tester is an economical, feature-rich, stand-alone wire harness tester offering up to 256 test points. The powerful NX Editor software application is used to create unique program files to successfully validate all electrical and electro-mechanical wire harness parameters. This tester is compatible with all Dynalab NX accessories such as printers, scanners, control ports, and much more. The NX Solo Tester supports network communications with the NX Server for efficient file transfers and advanced data collection.
-
Product
Multipurpose Debug Board
DB40-HPC Debug Module
-
The DB40-HPC Debug Card is designed for debugging of COM-HPC modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
Product
Voyager Intermittent Fault Detector
-
The Voyager includes a spread spectrum TDR so that the fault can be located. Once an intermittent is detected, the TDR is immediately connected to the failed test point and used to determine the distance to the fault.
-
Product
Design for Test Service
-
Design For Test (DFT) is a technique used to implement certain testability features into a product. Testing House can provide an analysis of the CAD data for testability of your circuit board. Access to a board can be very difficult as boards get smaller and designs get more densely populated. We can work with your design engineer to improve testability and maintain an effective in-circuit test. When access to the board is limited and boundary scan devices are present, we can provide the customer a list of key nodes that will require access in order to provide a very effective test. Our analysis will provide a list of all the accessible test points and an explanation for any nodes declared inaccessible.
-
Product
FM Tokenless Transmitter & Receiver
MS 1522
-
Transmitter and Receiver units are designed to work at 24V DC voltage (nominal) with variation between 19.2 V to 28.8V. The system is designed to work with carrier frequency 1800/2700 Hz and modulated frequency 65Hz/85Hz. For 1800Hz Carrier Frequency RED border is used in Front Panel and for 2700Hz Carrier Frequency BLUE border is used in Front Panel. Maximum power consumed by transmitter and receiver are 1.2W and 8W, respectively. Sense level for receiver is less than –19 dBm and No sense level for receiver is more than –22 dBm with 1mw (0 dBm) transmitter power. The equipment is designed to work satisfactorily with temperature variation from 0°C to 55°C with relative humidity of 95% at 35°C. Suitable test points are provided in the back of the equipment to monitor the necessary parameters.
-
Product
SWB-2833, 4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock
781421-33
-
4x71, 2 A, Electromechanical Relay Matrix Module for SwitchBlock - The SWB‑2833 is an electromechanical relay matrix card for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781421-17
-
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Melting Point Testers
-
These melting point testers are designed to accurately test the melting point of medium used in thermometers, for educational purposes, for quality control, automated process and more.
-
Product
Time Domain Replication (Road Load Simulation)
-
The powerful graphical editor makes it easy to review and compile your field sample data for use in the test lab. The point editor, filters, velocity and displacement compensation ensure the test feasibility is evaluated at an early stage. The continuous closed-loop controller then replicates the test files with very high levels of precision. The control algorithms use a continuous coherence averaging technique to ensure a stable proactive control loop that will not only provide accurate replication but will also respond to changes in test item dynamics.
-
Product
PC Controlled Low Voltage Tester
Cablescan S32
-
The Cablescan S32, with a 32-board Expansion Cabinet, may be ordered with 1 to 32 low-voltage 128-point scanner boards. Fully loaded with scanner boards, this tester provides 4096 test points.
-
Product
Optical Voltage Probe
400-02
-
Srico’s optical voltage probe uses advanced, proprietary optical chip technology to achieve precise, interference-free measurement. Our sensor and optical fibers are made of dielectric materials. This facilitates a high degree of isolation between the voltage test point and the instrumentation system ⎯ at a safe distance of 100 meters and more. This system senses, measures, and transmits electrical data very accurately.
-
Product
CAMGATE Test Kits
Series 453
-
LThe GR Series 453 CAMGATE mechanical kits, utilizing the patented CAM mechanism, offer precise Z axis linear motion when testing higher point count and finer pitch test centers. By using the Z axis motion, side load of the test probes is minimized thus increasing probe life and performance. The Series 453 provides interface compatibility using the GR2270 Style, 12 block interface. This interface accepts the industry standard I/O, power, and coax blocks. The CAM/GATE utilizes a cam roller system for precision guiding and smooth operation and 1.00” push plate movement. The gate assembly is movable to three different positions which allows for the versatility of top side probing, or relocating the frame assembly for PCA’s the have tall components.
-
Product
PXI Based Multifunction Measurement and ICT Instrument
PXI-501
-
The PXI-501 is a multifunction measurement instrument for functional and in-circuit measurements.It combines two parametric measurement units with a digital voltmeter, a high voltage current source and a discharge unit. This powerful combination makes it the ideal instrument for classical analog in-circuit test and manufacturing defect analysis with additional functional test capabilities.With it’s fast sampling rate of up to 4MSps it speeds up measurements and is capable of measuring and generating AC signals up to 100kHz.To enhance the PXI-501 capabilities it can be combined with an ABex TM-501 or an ABex TM-404. The ABex TM-501 enhances the in and output range of the PXI-501. Furthermore, it provides a shunt current measurement upgrade. In combination with the ABex TM-404 it’s a complete in-circuit test solution with 86 channels in one ABex slot. For sure it can be upgraded to 2838 test points in one rack by simply adding additional matrix modules.With the above-mentioned terminal modules, the PXI-501 is able to act as a ABex system controller, so that no additional controller is required in the cassis.
-
Product
Low Voltage Test System
CKT T1
-
The CKT T1 is a compact size solid-state test system featuring 128 test points.
-
Product
JTAGulator 24-Channel Hardware Hacking Tool
32115
-
On-chip debug (OCD) interfaces can provide chip-level control of a target device and are a primary vector used by engineers, researchers, and hackers to extract program code or data, modify memory contents, or affect device operation on-the-fly. JTAGulator is an open source hardware tool that assists in identifying OCD connections from test points, vias, or component pads on a target device.
-
Product
Vertisocket™ Horizontal Mounting
Series 800
-
Vertisockets Horizontal Mounting with Bifurcated Contacts. Aries offers a full line of VertisocketsTM for DIP packaging of LEDs, incandescent lamps, DIP switches, test points, etc. The variations of mounting position and pin configuration provide exceptional design freedom.
-
Product
Multipurpose Debug Board For EC
DB30 x86 Debug Module
-
The DB30 x86 Debug Card is designed for debugging of COM Express modules with FFC (FlexFoil Cable) debug connector. It includes an 80 port for Power on and Self-test (POST) via I2C interface, interface to SPI Flash for BIOS update, interface to EC for Embedded Controller (EC) update, Power and Reset buttons, and Status LEDs and Test Point for various debug tests.
-
Product
The Mag Lead
136
-
*Mag Lead features a magnetic disconnect near the test probe end. *Just disconnect the test probe and you can “stick” to any metallic ground or test point. *Quit fumbling with alligator clips that fall off - Mag Lead’s powerfull magnet will hold tight! *This is a time saving tool - if you don’t have to walk to your tool box to retrieve your alligator clips, even on just half the occasions, then you’ve saved time. *Very helpful for automotive reference points and troubleshooting. *Can eliminate the need to hold probes while checking or monitoring a signal. *Two high power, low resistance magnets hold the probe to the lead. *Fits almost all Digital Multimeters and can be used with hand-held scopes too. *Get the Mag Lead, it stays put and won’t fall off, like alligator clips do!
-
Product
Specialized Extender Card Testing IP Modules
IP-Debug-Bus
-
IP-Debug-Bus is a specialized extender card which is optimized for testing IP Modules. The bus signals are all accessible via test points. The testpoints include multiple ground locations and .025 sq. posts for ease of connection to your logic analyzer or scope. The testpoints are labeled for easy identification
-
Product
DIOS (Digital I/O Scan Module)
JT 2122/MPV
-
The JT 2122/MPV DIOS (digital I/O scan module) increases the coverage and improves the diagnostic resolution of boundary-scan testing by extending test access to connectors and/or test points. JT 2122/MPV DIOS provides bi-directional parallel-scan access to up to 128 or 133 I/Os in a standard DIMM-168 module.
-
Product
Digital Voltmeters
-
*Measures voltage from 5V to 25kV line to line*Large, easy to read LED display*Versatile for overhead and underground applications*Capacitive Test Point and Peak Hold modes
-
Product
SWB-2812, 16x9, 1 A, Reed Matrix Module for SwitchBlock
781420-12
-
16x9, 1 A, Reed Matrix Module for SwitchBlock - The SWB‑2812 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Testing Services
-
*Programmable Multipoint Tester*Over 8,000 programmable test points (DWV, Capacitance, Insulation Res., 2/4-Wire Resistance, etc.)*1500VDC / 1000 VAC Dielectric Withstanding Voltage (DWV)/ Hi-Pot (Programmable Dwell times)*Full Electronics laboratory complete with state of the art testing equipment*Custom Unit Testing (Designing of Specialized Test fixtures)*EMI Testing*Temperature and Humidity Testing*Shock Testing*Vibration Testing*Sand and Dust / Altitude Testing*Military Qualification Tests Performed
-
Product
Functional Test
cUTS
-
Get the essentials of measurement automation to power tests of simpler PCBAs and subassemblies. compactUTS (cUTS) is a cost-effective platform for automating manual tests of devices with fewer than fifty cable-accessible test points in manufacturing environments with moderate production volume. DUT-specific electrically keyed cables make changeover quick and easy.
-
Product
Robotic Probing of Circuit Cards
-
System provides reliable automatic access to test points on a printed circuit under test providing rapid and accurate diagnostic measurements. Accomplished by an automated test probe with video image capability, under control of application software running on a VXI Test System utilizing LabVIEW. A VXI Prober Interface Module (VPIM), developed to Plug and Play standards, provides interface between prober and VXI Test System.
-
Product
PNA-X Measurement Receiver for Antenna Test
N5264B
-
A new industry standard for antenna test with 400,000 point per second data acquisition on all five measurement channels Twice as many receivers available compared to any other antenna receiver on the market Replace existing 8530A and 8360 solutions for a system speed improvement that is 10 times faster Built-in 8510/8530A code emulation software provides a drop-in replacement for existing antenna ranges utilizing an 8530A
-
Product
Passive Oscilloscope Probes
5900 SERIES
-
Probe Master's new 5900 series passive oscilloscope probes are available in 400 MHz & 500 MHz bandwidths. Probes are also available with readout actuators for oscilloscopes with the readout feature. The "GOLD PROBE" has been designed specifically for use with Tektronix, Hewlett Packard and other high performance oscilloscopes. This new slim design along with a host of versatile accessories, allows you to reach the most difficult test point in today's highly complex circuitry. The gold plated Probe Tips, Sprung Hook, Ground Lead, Alligator Tip and other critical interconnect points within the Gold Probe, provide excellent contacts for probing low level analog signals and high speed digital data. Unlike most "off shore" commodity probes, Probe Master guarantees quality and continuing domestic support for our "Made in America" Gold Probe.The probe body is made of high impact ABS. Soft molded strain reliefs at all stress points assure long cable life. In short it has been designed to offer you high performance coupled with high quality.
-
Product
Offline In-Circuit Test Solutions
-
TestStation’s offline test systems are designed for a human operator or collaborative robot for product handling. TestStation systems scale to support from 128 to 15,000 test points. Our newest Multi-Site systems double productivity per system, reducing Capex and Opex for manufacturers.
-
Product
Silver Plated Test Points
-
The fabricators of SMT printed circuit boards may take advantage of the convenience of field testing with the unique loop design of Components Corporation's TP-107 and TP-108 series of surface mounted, printed circuit test points is now available in silver-plate for outstanding reliability. All products are RoHS and REACH compliant.
-
Product
ABex Matrix Module with 172x4 or 86x8 Cross Points
ABex AM-301 Matrix
-
The ABex AM-301 is a 172×4 matrix designed as a universal connection between the test points and the measuring instrument. This can be done locally or via the ABex. The ABex AM-301 can be configured as a matrix with 4 or 8 busses. The internal matrix busses can be switched to the analog bus.
