Flash Device
-
Product
FD-11637, 8-Channel Strain/Bridge Input Device for FieldDAQ
785641-01
-
8-Channel Strain/Bridge Input Device for FieldDAQ - The FD-11637 can measure eight channels and has built-in bridge completion and voltage excitation to support for quarter-, half-, and full-bridge sensors. It also features anti-alias filtering, offset nulling, and shunt calibration to reduce the effect of noise and improve measurement accuracy. The FD-11637 has an ingress protection rating up to IP67 (dust- and water-resistant), can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 grm vibration. The FD-11637 incorporates Time Sensitive Networking (TSN) and features an integrated network switch and built-in power circuitry for simple daisy chaining. You program the FD-11637 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. The FD-11637 is ideal for test cell and outdoor environments.
-
Product
Circuit Breaker Simulation Device
PSS01
-
PSS01 is the circuit breaker simulator，which can conduct circuit breaker simulation to test the whole secondary relay scheme together with relay test set. It is very good accessory for protection relay test kit to avoid complicated software programming to finalize the same test.
-
Product
Power Device Analyzer / Curve Tracer
B1505A
-
The Keysight B1505A Power Device Analyzer / Curve Tracer is the only single box solution available with the capability to characterize high power devices from the sub-picoamp level up to 10 kV and 1500 A. These capabilities allow evaluation of novel new device such as IGBT and materials such as GaN and SiC. The B1505A supports a variety of modules: high voltage SMU (HVSMU), high current SMU (HCSMU), ultra high current (UHC) module, ultra high voltage (UHV) module and high voltage medium current (HVMC) module. The B1505A also supports: high-power SMU (1 A/200 V), medium-power SMU (100 mA/100 V) ,medium-current SMU (1 A/30V pulsed, 100 mA/30V DC) and a multi-frequency capacitance measurement unit (1 kHz 5 MHz). Its ten-slot modular mainframe allows you to configure the B1505A to suit your measurement needs.
-
Product
USB-8502, 1-Port, High-Speed/FD, USB CAN Interface Device
784661-01
-
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
G7 Connected Safety Devices
-
Our G7 product line incorporates leading incident detection and advanced location technology with 3G and satellite communications to ensure seamless monitoring. From gas detection to lone worker monitoring and evacuation management, G7 has your teams covered.
-
Product
PCIe-8510, 2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device
785324-01
-
2- or 4-Port, PCIe Vehicle Multi-Protocol Interface Device—The PCIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PCIe‑8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
PXIe Programmable Device Power Supply
33020
-
High channel density with 8 channels per card 6V-12V independently programable voltage level Max. current gang feature providing max. 4A output per card
-
Product
Foreign Matter Inspection Device For FPDs
HS-930
-
By adopting our original optical technology, we achieve an inspection speed of about 30% up (compared to HS-830). Improved the front / back judging ability to thin substrates.
-
Product
DALI, DSI, DMX & RDM Commissioning Device
ADDICT
-
A revolutionary, purpose-built, portable multiprotocol tool for DALI, DSI, DMX512-A & RDM. The ADDICT can back up, store and program DALI devices from stored settings (as requested by Osram head office Germany). The ADDICT can also continuously sniff the DALI line to a PC with English descriptors (as requested by Philips R&D Europe). The ADDICT provides full DALI, DMX and RDM testing and commissioning facilities including DMX and DALI sniffing.
-
Product
RTSI Bus Cables for 4 PCI or AT/ISA Devices
776249-04
-
34-Pin Female RTSI to 34-Pin Female RTSI Ribbon Cable - The RTSI Cable, sometimes referred to as RTSI, connects RTSI bus connectors on adjacent NI plug-in boards. The RTSI Cable is offered with different numbers of ribbon connections and in different lengths.
-
Product
Recorder Carrier Device
RCD
-
The RCD is a carrier signal demodulator for SCADA and Fault Data Recording. the RCD demodulates the carrier to indicate the presence of a relative level of a singal
-
Product
Smart Aircraft Interface Devices
webCS
-
The Ballard webCS® is the first highly integrated smart AID/server/router that securely bridges avionics data with wired and wireless networks in a single compact box. This wireless aircraft communications server platform is simple to install and configure, safe to interface with aircraft domains, and provides highly secure data transfer. The compact, versatile webCS enables aircraft operators to easily gather and process aircraft data, and then route it to where it is needed—whether on or off the aircraft.
-
Product
Electricity Metering Device- Residential
Mk31
-
Built on the Papillon metering platform, Mk31 is a multi-functional meter with advanced features such as tamper detection, multi-tariff capability, neutral current measurement and multiple communication options including RS-485 and RF.
-
Product
Biomagnetic Devices
-
Electrical measurements of physiological potentials are well established in clinical diagnostics. The flow of an electrical current creates a corresponding magnetic field. Thus bioelectric activity will generate biomagnetic fields. These fields can be detected with Tristan SQUID magnetometers. For many of the classical electrical techniques such as ECG and EEG, there are corresponding magnetic techniques (magnetocardiography or MCG and magnetoencephalography or MEG). In some cases (magnetopneumography, hepatic iron store measurements, intestinal ischemia, peripheral nerve and muscle activity), there is no corresponding electrical technique and biomagnetic measurements offer unique measurement capabilities. Unlike CT or MRI imaging which yield structural information, biomagnetic measurements offer real-time functional imaging.
-
Product
Measuring Devices for Magnetically Soft Materials
MAG-RJJ-6.0
-
The computerized measuring system is designed for measure the dynamic magnetic properties of the soft magnetic materials e.g. oriented or not-oriented electrical sheet. The system provides the opportunity of a tabular and graphic presentation of the obtained data, which can be presented by means of monitor, printer or plotter.
-
Product
Pocket-Sized Analyzer for Capturing & Decoding USB 2.0 Devices
Mercury T2C / T2P
-
The pocket-sized Mercury T2C & T2P capture and decode the widest range of USB 2.0 device classes plus Type-C link states and Power Delivery 3.0 messages. Both the Mercury T2C and T2P utilize the industry leading CATC Trace analysis software for verifying and debugging USB and PD protocol issues. Now there are two base models to choose from; the original Mercury T2C and the new Mercury T2P, which adds the Power Tracker graphical view of VBUS and CC voltages.
-
Product
*PCIe-5785, 12-Bit, 6.4 GS/s, 2-Channel FlexRIO IF Transceiver Device
785589-01
-
The PCIe-5785 enables direct RF acquisition up to 6 GHz and generation up to 3 GHz with 12 bits of resolution. You can use it in a dual-channel mode at 3.2 GS/s or in a single-channel interleaved mode at 6.4 GS/s. The PCIe-5785 is ideal for applications that require wideband acquisition and generation with multichannel synchronization, including radar, electronic warfare, and communications. The FlexRIO driver includes support for acquiring and generating waveforms out of the box, and you can use the LabVIEW-programmable Xilinx Kintex UltraScale FPGA to implement custom algorithms for real-time signal processing.
-
Product
Network Synchronization Device
VCH-003
-
The Network Synchronization Device (NCD) VCH-003 is intended for use on the Unified Telecommunication Network of the Russian Federation. Depending on the configuration of the NSS, VCH-003 can be used to generate and multiply synchronization signals of 2048 kHz and 2048 kbps as part of the PEG, as an OIG to restore synchronization signals received from the line at the transit node.
-
Product
Partial Discharge Detection Calibration Device
-
Hangzhou Xihu Electronic Institute
Calibration Device of Transient Earth Voltage PD detector, calibration device of ultrasonic PD detector, calibration device of high frequency PD detector, calibration device of ultra high frequency PD detector.
-
Product
Earth Leakage Breaker And Residual Current Device
IGR Series
-
IGR Leakage Current Analyzer is invented as the world first, and also can measure Insulation Resistance (MO) without power cut-off. This patented instrument can analyze leakage current, and display Igr(resistive), Igc(capacitive), and Io(vector sum), Ground Insulation Resistance, and the phase angle between voltage and current. (IGR ELB) - Operates due to Igr. - Properly-operating in spite of IGC in digital era. ( Not tripping on UPS load and Harmonics and noise area) - Possible to go down Igr for safety of people and animals. - Possible to manufacture high sensitive ELB. - Possible to prevent fire from electric leakage current.
-
Product
GPIB-RS232, Instrument Control Device - United States 120VAC
779732-01
-
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a … talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
Product
A/D MODULE OF THE COMPACT DEVICE FAMILY
ES610
-
This module measures analog voltages using 16 electrically insulated measuring channels at the adjustable acquisition rate per module of max. 2k samples/s, min. 0.5 samples/s. Signal smoothing occurs through a parameterized software filter, and 16- bit resolution ensures high measurement accuracy. Selectable measuring ranges are 10 V and 60 V. Data transfer to PC occurs via Ethernet.
-
Product
RTSI Bus Cables for 5 PCI or AT/ISA Devices
776249-05
-
34-Pin Female RTSI to 34-Pin Female RTSI Ribbon Cable - The RTSI Cable, sometimes referred to as RTSI, connects RTSI bus connectors on adjacent NI plug-in boards. The RTSI Cable is offered with different numbers of ribbon connections and in different lengths.
-
Product
Smart Device Testing
-
Helping you ensure that your smart devices with integrated wireless modules meet requirements to demonstrate compliance to global wireless type approval requirements.A smart device is any piece of electronic equipment that intentionally communicates and interacts with other electronic devices using wireless protocols. In order to verify the performance and connectivity of these devices, both the device hardware and the communication protocol are evaluated to ensure smooth connectivity and eliminate unacceptable interference.
-
Product
Temperature Input Device
-
The Temperature Input Device is a thermocouple measurement device featuring InstantDAQ technology. InstantDAQ technology includes built-in software for viewing and logging data that automatically loads when you plug in the device, so you can instantly take temperature measurements with your PC. You can connect the Temperature Input Device to any USB port to use your PC as a display and monitor data in real time. The device is compatible with J, K, R, S, T, N, E, and B thermocouples.The Temperature Input Device includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
PCIe-8239, 4-Port, GigE Vision Frame Grabber Device
787790-01
-
The PCIe-8239 features Power-over-Ethernet (PoE) technology. It provides optimized performance of high-resolution and high-frame rate cameras through the combination of independent Gigabit Ethernet ports and the high-performance GigE Vision driver software. PoE reduces the need for additional external power supplies by powering cameras over the Ethernet bus, which simplifies system design and cabling complexity.
-
Product
IOT Device Management Platform
-
The Internet of Things revolution is ongoing and has gained significant traction over the last few years. This revolution is based on the availability of huge amounts of information coming from the data sensed and transmitted by intelligent connected objects. In order to cope with this revolution, the importance of efficient and reliable monitoring and management tools has increased significantly.
-
Product
High-Voltage Test Device
PGK 70/2.5 HB
-
Cable testing and diagnostics with the BAUR PGK HB. There are hardly any other longer-lasting, more robust and cost-effective testing devices than the two-piece high-voltage test devices from the PGK HB series. They generate continuous adjustable test voltages with mains frequency or optionally DC with positive or negative polarity. The display instruments for current and voltage, the safety control unit and the regulating transformer for the voltage are integrated in the operating unit.* Operation as DC or Ac testing device* Polarity of the DC voltage can be easily be reserved* Robust and durable
-
Product
Wire Damage Test Device For Pull Testing
IEC60884 FIG11
-
Shenzhen Chuangxin Instruments Co., Ltd.
IEC60884 FIG11 Wire damage test device for pull testingThe wire damage test device is a special test instrument designed and manufactured according to the requirements of IEC884 Figure 11, , etc. It is mainly used to judge whether the screw-clamp type terminal is in design and structure.
-
Product
Test And Simulation Devices
BreakingPoint
-
Control global threat intelligence at Internet-scale to create massive-scale, high fidelity simulation and testing conditions for battle-testing infrastructures, devices, applications, and people.
