Reference Transmitters
high quality optical transmitters for test and measurement.
See Also: References, Reference Standards, Reference Antennas, Reference Decoders, Reference Jumpers, Reference Sources, Reference Transformers, Acoustical References, Frequency References, Solar Reference Cells, Fiber Optic
-
Product
Conductivity Transmitter
DO9766T-R1
-
output of a conductivity electrode with temperature compensation into a 4÷20 mA signal.
-
Product
Temperature and Humidity Transmitter
T3419-4
-
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
CW Transmitters
-
The Praxsym CW Transmitter is a complete, portable continuous wave test source. Used as an input source to test a distributed antenna system, the Praxsym CW Transmitter can provide test signals aiding in the design and optimization of in-building and outdoor networks.
-
Product
Radar Level Transmitter
DR5400
-
DR5400, FMCW 24 GHz open air radar is a market entry level transmitter for liquids in basic process applications. This model has proven PP Drop antenna design which is insensitive to condensation.
-
Product
Barometric Pressure Transmitter
T2414
-
Barometric pressure transmitter for outdoor and indoor use.Display reading and pressure output is user selectable in these units: hPa, kPa, mbar, mmHg, inHg, inH2O, PSI, oz/in2.
-
Product
Pressure Transmitters
-
Explosion-proof pressure transmitter is approved for use in hazardous locations per CSA Standard 30 and UL Standard 1203 for Class 1, Division 1 and Division 2 hazardous locations. Wetted parts are all 316L Stainless Steel (50 up to 10000 PSIG), 17-4PH (15000 & 20000 PSIG) for compatibility with a variety of media. Wetted materials and construction comply with the NACE MR0175 Standard. The KP46 Series explosion-proof pressure transmitter's fitting and sensing diaphragm are machined out of a single piece of material, so there are no welds, seams or O-ring seals, resulting in excellent long-term performance and stability. The case is factory sealed, making this pressure transmitter very rugged with excellent shock and vibration resistance.
-
Product
CO2 Concentration Transmitter
T5340
-
The transmitters are designed for online measurement of temperature (C or F), relative humidityand carbon dioxide concentration of air without aggressive ingredients. Measured temperature andrelative humidity are recomputed to following humidity expression: dew point temperature, absolutehumidity, specific humidity, mixing ratio and specific enthalpy.
-
Product
Audio Frequency Transmitter
TG 600
-
Cable fault location with the BAUR TG 600. The TG 600 audio frequency transmitter was designed specifically for the precise location of cable faults and joints using the twist method. The display of the input and output current makes selection of the correct adjustment easier.* High-performance audio frequency transmitter up to 600 VA* Frequency of 2 or 10 kHz, quartz-stabilised (other frequencies on request)* Potential-free output* Impedance adjustment in 8 steps from 0.3 to 300 Ω
-
Product
Universal Transmitter
Model LXT-330
-
Teledyne Analytical Instruments
Model LXT330 Liquid Transmitter is a single or dual channel, universal, multi-parameter transmitter, designed for continuous online liquid measurements. It is paired with SP3 Smart sensors and is intended for use in non-hazardous, general purpose rated industrial environments. The SP3 sensor platform covers a wide range of liquid analytical measurements, such as pH, ORP, Specific Ion (pION), dissolved oxygen, free chlorine, total chlorine, conductivity, resistivity and turbidity. The LXT330 transmitter can be used with any SP3 smart sensors without additional user reconfiguration. The Universal Transmitter & Smart Sensor loop philosophy removed the need to stock for multiple instrument types. The process parameter, sensor details, serial number and calibration history are stored in the sensor's main memory, facilitated by two-way digital communication between the sensors and transmitter. The LXT330 universal transmitter allows for up to two SP3 sensors per transmitter (contact factory for available combinations).
-
Product
Redundant Reference Frequency Shaper
CH7-317
-
Redundant reference frequency shaper Ch7-317 is designed to generate and reproduce frequency and time signals protected from frequency and phase failures based on the results of signal processing from a group of frequency and time keepers.
-
Product
Configurable Thermocouple Transmitter
HD778TR1
-
Configurable 4...20 mA/20...4 mA 2 wire temperature transmitter for K, J, T, N thermocouples.
-
Product
HVAC Pressure Transmitter
DP850/851
-
The DP850/851 transmitters are designed for low pressure measurement in HVAC applications. The DP850 is available in full scale pressure ranges as low as 0.25 inH2O and the DP851 can be ranged to 0.025 inH2O full scale. Both models are available in 4-20 mA or 0 to +5 Vdc signal output options.
-
Product
Barometric Transmitter with Display
HD9908T… Series
-
Digital barometric transmitter with LCD indication, 3½ digit, minimum and maximum relay.
-
Product
Attitude Heading Reference System
M&M Modules
-
PNI’s M&M modules will self adapt and learn its system and its environment automatically to provide accurate quaternions, heading, pitch and roll. All while using 100 times less power than traditional AHRS modules.
-
Product
CO2 Concentration Transmitter
T5241
-
CO2 concentration transmitter with 0-10V output is built in a durable watertight case. Output range is user adjustable. Large dual line LCD is an advantage. Display is possible to switch off. The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
Product
Low Phase Noise Reference Source
96270A
-
The 96270A RF Reference Source is the simplest, most accurate and cost-effective single instrument for calibrating spectrum analyzers and RF power sensors and more, up to 27 GHz.
-
Product
Loop-Powered Transmitters and Drivers
4-20mA
-
Loop-Powered Transmitters convert the output from proximity probes, seismic sensors, into a 4-20mA DC current, which is proportional to the input being measured. The transmitter converts the displacement or vibration signal to DC voltage and/or current for a DCS or PLC system. They control a 4-20mA current loop for a specified vibration range (ex. 0-5 mils peak-to-peak). The transmitters have a two-wire hook-up, powered solely by the loop current and have a power supply range of 15 to 36 volts.
-
Product
CO2, CO2 and Temperature Transmitters
HD37…
-
The transmitters of the HD37… series are used mainly in air quality control by measuring CO2 (Carbon Dioxide) in the ventilation systems. This allows you to vary the number of air change per hour according to ASHRAE and IMC norms.
-
Product
Transmitters
-
Transmitters are used for industrial applications to convert process signals into standardized isolated output signals 0-10V or 0 / 4-20mA. In addition to the process signals, various sensors can also be connected, e.g. Pt-100, thermocouples, potentiometric sensors, inductive, capacitive and optical initiators, resistors, etc. The transmitters are supplied with 230VAC or 24VDC and housed in a DIN housing for 35mm rail mounting.
-
Product
Temperature Transmitters
-
Temperature transmitters convert thermocouple, RTD, and low-level temperature sensor signals to 4-20mA, 0-10V, or other DC voltage/current outputs. Acromag offers temperature transmitters in head-mount and DIN-rail form factors. Some temperature transmitters have software-configured universal input to convert a broad range of temperature sensor and other signals with a single unit.
-
Product
Transmitter / Receiver Modules
-
An RF module (radio frequency module) is a (usually) small electronic device used to transmit and/or receive radio signals between two devices. In an embedded system it is often desirable to communicate with another device wirelessly. This wireless communication may be accomplished through optical communication or through radio frequency (RF) communication. For many applications the medium of choice is RF since it does not require line of sight. RF communications incorporate a transmitter and/or receiver.
-
Product
T100 Toxic Gas Transmitter
-
The T100 is a 4-20mA 2-wire transmitter that can measure a wide range of gases. Housed in a rugged, compact metal enclosure, it is designed to be maintenance free and inherently stable.
-
Product
CO2 Concentration and Temperature Transmitter
T8148
-
CO2 concentration and temperature transmitter with two 4-20mA outputs is specially designed for use in exacting interiors in building energy management and HVAC systems. It designed for easy installation on ordinary KU68 wiring boxes for household switches and sockets. Large dual line LCD is possible to switch off. Computerized design ensures long term stability and fail indication. Transmitter is designed for use in non-aggressive environment.
-
Product
Magnesense Differential Pressure Transmitter
MS
-
The Series MS Magnesense Differential Pressure Transmitter is an extremely versatile transmitter for monitoring pressure and air velocity.
-
Product
Reference Electrodes
-
Reference electrodes are widely used as: electrochemical measurements (CV, LSV, DPV, etc.) electrochemical devices (detectors for HPLC, biosensor, etc.)
-
Product
Clear Room Logger Transmitter
HD50CR
-
The HD50CR is the ideal solution for monitoring of differential pressure, temperature and humidity in Clean Room applications.
-
Product
Micropower Voltage References
-
Analog Devices offers a broad line precision micropower voltage references with extremely low quiescent currents (series references) or minimum shunt currents (shunt voltage references). All of our precision voltage references offer excellent initial accuracy and low temperature drift over time and temperature. Our Reference Plus products combine precision voltage references with comparators or amplifiers.
-
Product
Barometric Transmitter Wall Mount
HD4V8TBARO
-
Barometric transmitter to wall mount for indoor use, suitable for installation in the housings for weather stations.
-
Product
Fiber Transmitter With Fiber Amplifier
FTFA 822B - 824B
-
- Work as Transmitter & Fiber Amplifier- AGC - Automatic Gain Control- Built in RF Booster- Higher RF at next connected Node- Maintain MER/BER for Digital FTTH Transmission- High Quality DFB Lesers with Isolaters- Variable SLOPE Control- Output Wavelength : 1310nmPower Options :- 40V DC- 12V DC / 2 Amp- STB Adapter along with PSP- 7.4V, 2600 mAH Battery
-
Product
Wireless IoT Sigfox Transmitter
-
Wireless IoT transducers / transmitters for temperature, humidity, binary input, atmospheric pressure.
