Pulse Oximeters
assure function of
-
product
Pulse Adapter
CV30P650
Frothingham Electronics Corporation
The CV30 P650 test station is currently the highest voltage pulser in a series of exponential pulse generators that can be connected to our FEC200E tester. This gives you all the versatility of the proven FEC200 with the addition of high power exponential pulses. The CV30 P650 pulse adapter can produce a maximum current of 100A at up to 600V using exponential pulses up the 10/1000 waveform. The pulser is rated at 30KW from 300V to 650V. Voltage compliance at 100A is 600V. The station can also include all of the usual FEC200 tests in the same test program.
-
product
Pulse Generator
PulseGen
Pulse Generator for use with an oscilloscope as a Time Domain Reflectometer (TDR).
-
product
Transient Pulse Generator
8282-1
The Model 8282-1 Transient Pulse Generator was designed for screen room use in making conducted spike susceptibility tests. It provides all the waveshapes required by MIL-STD-461B/C and many other military EMI specifications
-
product
DC-Coupled Pulse Amplifiers
These DC-coupled pulse amplifiers are available in a simple DC-power module format, and are also available in an AC-powered benchtop instrument format. All models will drive a 50 Ohm load.
-
product
For Detecting Low Range And Leakage AC/DC/Pulsed Current.
FDAZCT-20LSP-0.3S
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Lowest Influence from Magnetization,Temperature *Change,Residual Current and Terrestrial Magnetism.*Low Cost and High Performance (Output Linearity ±1% F.S)
-
product
Single Long Pulse Solar Simulator & I-V Test System
TriSOL SLPSS
The OAI Test System for HIGH EFFICIENCY SOLAR CELLS overcomes the limitations of flash testing by providing a highly optimized pulse width and voltage sweep rate to match the cell’s dielectric response speed. As a result, the system produces extremely accurate measurements of solar cell efficiency leading to increased profitability.
-
product
4 Channel 1.0 ~ 17.0 Gb/s Pulse Pattern Generator and Error Detector
CA9806
The UC INSTRUEMNTS CA9806 is a high performance, flexible four channel Pulse Pattern Generator and Error Detector that can operate from 1.0 to 17.0 Gb/s (consult factory for higher or lower operation speeds). It is also a standalone Bit Error Rate test solution that incorporates an internal full rate clock synthesizer. Its small size allows it to be placed close to the device under test, it can also be placed further away using the TX driver pre and post emphasis controls features to compensate for cable and interconnect losses. It also has a non destructive, integrated eye outline capture feature along with a quick eye height and width measurement capability. Build‐in 8.5 ~ 15 Gb/s eye diagram testing function.
-
product
Pulsed Withstand Voltage Safety Test
Suzhou 3ctest Electronic Co.,Ltd.
designed to test the induced and conducted disturbance on the telecom lines generated by power line and electrical railway. It meets the requirements of YD/T 993-2006(The technical requirements and test methods of over-voltage and over-current resistibility for telecommunication terminal equipment),
-
product
120 A Manual Pulse Width Extender
TLP-12012A6
High Power Pulse Instruments GmbH
- Pulse width extender for the high current TLP/HMM test system TLP-12010A and TLP-12010C- 6 manual selectable pulse width: 5, 10, 50, 100, 200 and 500 ns- High pulse output current up to ±120 A- High performance and high quality components
-
product
Hydraulic Pulse Fatigue Testing System
PFT-500
Jinan Testing Equipment IE Corporation
PFT-500 hydraulic pulse fatigue testing machine is mainly applicableto large size parts such as bridges, trusses, automotive chassis, front and rear axels, locomotive frames, chassis and various concrete structures for static compression test and dynamic unidirectional pulse fatigue tests. The Fatigue Testing System for Rail has significant characteristics of reliable design, simple operation, energy conservation, and low operation cost etc.
-
product
Flex Power Pistol Grip Auto Shut-Off Pulse Tools
Auto shut-off pistol grip pulse tool that automatically shuts off the air supply when the pre-set torque is reached. The pistol grip models are commonly used for vertical operations. Designed for safe, reaction free operation for various industrial assembly applications. The FlexPower Pulse Tools provide operators with an industry leading power-to-weight ratio, allowing for a smaller tool selection for greater torques giving operators a lighter tool with more torque capability. Ergonomically safer than harmful hammering and vibration of impact wrenches. Built for durability with a superior O-ring design and specially designed pulse fluid FlexPower extends life between regular oil changes and provides more torque stability. Offers comfortable rubberized non-slip grips for easy handling and excellent thermal ergonomics. Low noise decibels, minimal vibration and low torque reaction. It is important to understand your joint application before a selecting a pulse tool.
-
product
50MHz Dual-Channel Pulse Waveform Generator
PM8572A
Model PM8572A is very high performance, dual channel pulse/pattern generator that stretch normal pulse generators` spec to the limit, becoming by far the most advanced pulse waveform generator available in the market. In addition to its high performance pulse features, the new PM8572A generate a complete array of standard, arbitrary and sequenced waveforms which are necessities in today`s laboratories.
-
product
USB Power Sensor - 100 MHz to 8 GHz, Average, Peak (Pulse)
GT-8551B
The Spanawave/Giga-tronics GT-8550B USB Power Sensors offer easy-to-use high-performance RF and microwave power measurement. High dynamic range and high accuracy make these sensors ideal for testing in wireless communication applications and Defense EW systems. The GT-8550B series feature a ruggedized body and fast measurement speed. These broadband power sensors provide easy-to-use, fast, accurate power measurement for R&D laboratory, manufacturing test and field installation and maintenance applications.
-
product
12-Watt Pulsed FAYb Fiber Laser
LP-V Series
Panasonic Industrial Devices Sales Company of America
The LP-V series is a 12-watt, pulsed fiber laser.Characteristics:- Very high resolution- Fine marking area- Small air cooled head
-
product
High Voltage 50 Ω Pulse Generator for CMTI
CMTI-8010C
High Power Pulse Instruments GmbH
The CMTI-8010C is a high voltage 50 Ω pulse generator for static and dynamic common mode transfer interference (CMTI) evaluations of digital isolators according IEC-60747-5-5 and IEC-60747-17.
-
product
Pulse Function Arbitrary Noise Generator
81160A
Generation of 330-MHz pulses and 500-MHz function/arbitrary waveforms with a 2.5-GSa/s sample rate and 14-bit vertical resolution; Selectable crest factors for white Gaussian noise lets engineers determine how much distortion to apply to a device during stress testing to meet various serial bus standards; Glitch-free timing parameter changes allow engineers to change the frequency without drop-outs or glitches and enable continuous operation without rebooting or resetting the device under test; and Arbitrary bit patterns show capacitive load of the channels using simple pattern settings. Complex measurement setups are no longer necessary to test designs to their limits. Pulses 330 MHz, 500 MHz sine waves, 660 Mbit pattern
-
product
Ignition Pulse Detector
IP-3100
The IP-3100 enables ignition pulse detection of gasoline engines with high sensitivity. The rotation speed can be easily measured by clamping the primary side cord (low voltage), the secondary side cord (high voltage), and current cable of the electronic distributor. The IP-3100 is used with the tachometer made by Ono Sokki.
-
product
Square Lenticular Pulsed Backlight
ViTech B108
Lensed illumination is intended for pulsed illumination of objects in machine vision systems, in which it is not possible to mount an additional light source close to the object or where it is necessary to create the required glow intensity in a certain area. A distinctive feature of the B108 modules is the absence of persistence (except for the version with white LEDs).
-
product
Voltage Pulse Generator
LSG-65C
Shanghai Sanki Electronic Industries Co., Ltd.
The waveform parameters of the voltage pulse generator LSG-65C fully meet the requirements of IEC60065 and GB8898; the pulse voltage output of up to 10kV can meet the requirements of different test levels of users; the self-developed high-voltage electronic switch is adopted , which has high stability, low noise and long service life. Long; digital display mode, intuitive and easy to operate.
-
product
10MHz Pulse Generator With Delay
TGP110
0.1Hz to 10MHz frequency rangeIndependent control of pulse frequency, width and delay50ns minimum pulse widthSquare wave, double pulse & delayed pulse modesFree-run, gated and triggered modes50 Ohm output: 0.1V to 10V amplitudeTTL/CMOS and Sync outputs
-
product
Digital Delay Pulse Generator
9420 Series
The Model 9420 Series Digital Delay-Pulse Generator with 2, 4 or 8 independent outputs is designed to provide cutting edge, yet cost-effective solutions to generate and synchronize multiple pulses for a wide range of applications. The delay and pulse width for each channel are independent and digitally controlled which makes the instrument ideal for situations that require synchronizing a number of different events. Channels: 2, 4, or 8 Independent Channel Outputs. Resolution: 10ns. Accuracy: 1ns + .0001 x period.
-
product
50 Ω High Voltage Pulse Generators
High Power Pulse Instruments GmbH
50 Ω High Voltage Pulse Generators by HPPI GmbH
-
product
Calibration Pulse Processor
2401
TESCO’s Calibration Pulse Processor (Catalog No. 2401) adapts to any Next Generation three phase test board to directly calibrate with three independent single phase standards.
-
product
30 Amps, 100 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP031
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
product
Split type Pulse Current Sensor
PCT-06
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Through hole type pulse current sensor.*Pulse current sensor for power demand meter.
-
product
Frequency & Pulse Distribution
Timetech frequency distribution amplifiers and pulse distribution units.
-
product
Split type Pulse Current Sensor
CTF-03
MULTI MEASURING INSTRUMENTS Co., Ltd.
Suitable for the operation and cable continuity check of the equipment by pulse current detection method. Wide AC current range from 0.1mA to 8A. Ultra compact and light weight. High sensitivity and least affection from external magnetic field.
-
product
Pulsed IV Systems
AM3200-Series
AMCAD Engineering has created professional, industry-proven pulsing technology for both standalone IV-testing (Pulsed IV, PIV) as well as pulsed-bias load pull (Pulsed Load Pull, PLP) and high-voltage power semiconductor applications. Systems come equipped with a mainframe controller which includes integrated power supplies. Input and output pulser modules (probes, pulsers) are selected for specific applications and are available in bipolar ±25V/1A and high-voltage 250V/30A models.
-
product
30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP030
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.





























