PIN Diode Switches
-
Product
PXI 8-Slot BRIC Matrix, 220x4 1-Pole (5 sub-cards)
40-562B-121-220X4
Matrix Switch Module
The 40-562B-121-220X4 is a high density BRIC8 matrix module with a size of 220x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
LXI High Voltage Matrix 2-pole 200x2
60-310-202
Matrix Switch Module
The 60-310 is a 2-pole Matrix Module available in 300x2, 200x2 and 100x2 formats. It is capable of cold switching 1000VDC and has a maximum carry current of 1A. It is designed for high voltage applications including circuit board isolation testing, relay testing, semiconductor breakdown monitoring and cable harness insulation testing.
-
Product
PXI 12-Slot BRIC Matrix, 60x32 1-Pole (12 sub-cards)
40-562B-321-60X32
Matrix Switch Module
The 40-562B-321-60X32 is a high density BRIC12 matrix module with a size of 60x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI Microwave Transfer Switch, Single, 26.5GHz, 50Ω, SMA
40-782B-531
Switch Module
The 40-782B-531 (PXI) and 42-782B-531 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 26.5GHz. Connections are made via front panel mounted high quality SMA coaxial connectors.
-
Product
8-Slot BRIC, 252x12, 1 Pole, PXI Matrix (6 Sub-cards)
40-559-801-252x12
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI/PXIe RF Switch, Dual SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-001
Switch Module
The 40-880B-001 (PXI) and 42-880B-001 (PXIe) are dual SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range has automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in a two slots or hex and octal switches in three slots.
-
Product
PXI 16x4 Signal Insertion and Monitor Matrix
40-525A-002
Matrix Switch Module
This is a PXI signal insertion and monitor matrix with switched pass thru connections on both X and Y axis. It is also available in a 34x4 format and can be used for signal insertion and monitoring purposes on connections between the UUT and test system.
-
Product
LXI High Density 384x8 Matrix with BIRST
60-550-026
Matrix Switch Module
High-density single pole matrix module capable of switching up to 300VDC/250VAC, or 2A (60W max). The use of high-quality electro-mechanical relays offer high switching confidence and make it suitable for signal routing in large ATE systems.
-
Product
PXI Single 64x4 Matrix 1-Pole Switching
40-533A-021
Matrix Switch Module
Typical applications include signal routing in Functional ATE and data acquisition systems. These PXI matrix modules are constructed using high reliability sputtered Ruthenium reed relays, offering >109 operations to give maximum switching confidence with long life and stable contact resistance.
-
Product
PXI 12-Slot BRIC Matrix, 308x4 1-Pole (7 sub-cards)
40-562B-321-308X4
Matrix Switch Module
The 40-562B-321-308X4 is a high density BRIC12 matrix module with a size of 308x4 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
High 2.90 (82.20) - 12.60 (357.00) Switch Probe
TSP100-H180-3
Switch Probe
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
Product
PXI Solid-State Matrix Module, 6x2, 10 A, Hardware Interlock
40-553A-011-HI
Matrix Switch Module
The 40-553A-011-HI is a high current 6x2 matrix with hardware interlock occupying two slots of PXI chassis. Each matrix crosspoint uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation.
-
Product
SIMRC - 8 x 4 Matrix 1-Pole
1030-R-8-4-1-5/1D
Matrix Switch Module
Our small format embedded switching (SIM relay) cards offer a choice of switching configurations using low cost industry standard SIM connectors. They free the designer from the detail of routing complex switching circuits, you may select from a wide range of cards using the built in RS-232 and I2C interfaces. These low-cost embedded switching cards are intended to be mounted on to a simple motherboard. They may be used to construct very high density switching networks. SIM based switching cards also allow for very simple in-field maintenance.
-
Product
LXI Microwave Matrix, 10GHz, Single 4x4, Terminated
60-750-144-B
Matrix Switch Module
The 60-750-144-B is a single 4x4 10GHz microwave matrix with internal termination. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection.
-
Product
PXI 4 Slot BRIC 232x6 2A 1-Pole Matrix
40-596-004
Matrix Switch Module
The 40-596 PXI Matrix BRIC provides a range of high density matrix modules able to switch up to 2 Amps or 150VDC/100VAC. The 40-596 BRIC modules are available in 2, 4 or 8-slot PXI sizes to suit most high performance PXI Matrix requirements, constructed using high quality electromechanical relays for high switching confidence.
-
Product
PXI 4-Slot BRIC Matrix, 2A, 2-Pole 110x4, 2 Sub-cards
40-566B-002
Matrix Switch Module
The 40-566B-002 is a 110x4 matrix with 2-pole switching and is part of a range of high-density large PXI matrix modules with the ability to switch up to 2 Amps or 300VDC/150VAC. They are available in 4 or 8-slot PXI sizes and are constructed using quality electro-mechanical relays for high switching confidence.
-
Product
PXI 4 Slot BRIC 180x8 2-Pole (6 sub-cards)
40-561A-022-180X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8 slot PXI sizes to suit all high performance matrix requirements and are constructed using instrumentation quality reed relays. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI BRIC4 FIBO Matrix Dual 31x4 2pin brkout
40-592A-011
Matrix Switch Module
The 40-592A FIBO (Fault Insertion Break-Out) Matrix Module is a large-scale high density switching matrix based on the Pickering BRIC format. The fault insertion BRICs are designed for applications requiring the simulation of a variety of faults in complex, high pin count, applications involving sensors and control units. Typical faults that can be simulated are open-circuits, short circuits to ground or battery, or short-circuits between input/output lines.
-
Product
Switch Modules - 16 Single Pole Relays Arranged as an 8x2 Matrix
JX16/AB-1
Switch Module
This module has 16 single pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 matrix. It is available with Type S or M reed relays for high speed, long life application. These modules are usually used for 2 wire testing where high and low meter leads must be switched between any two points. Often used for 2 wire LCR meter measurements, cable testing, or open / short testing in a variety of applications.
-
Product
Microwave Transfer Switch
60-808-510-001
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI 8-Slot BRIC Matrix, 40x32 1-Pole (8 sub-cards)
40-562B-121-40X32
Matrix Switch Module
The 40-562B-121-40X32 is a high density BRIC8 matrix module with a size of 40x32 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 4-Slot BRIC Matrix, 264x4 2-Pole (6 sub-cards)
40-562B-022-264X4
Matrix Switch Module
The 40-562B-022-264X4 is a high density BRIC4 matrix module with a size of 264x4 with 2-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 4 Slot BRIC Solid State 128x8 1-Pole (4 sub-cards)
40-563A-021-128X8
Matrix Switch Module
This version of our BRIC is part of a range of high-density PXI matrix modules. These modules are available in 2, 4 or 8-slot PXI sizes to suit all high performance PXI matrix requirements and are constructed using solid-state switches. With this high level of switching density, these PXI matrix modules allow a complete Functional ATE system to be housed in a single 3U PXI chassis. These BRIC matrix modules allow the use of lower cost 8 or 14-slot PXI chassis.
-
Product
PXI 12-Slot BRIC Matrix, 165x16 1-Pole (15 sub-cards)
40-562B-321-165X16
Matrix Switch Module
The 40-562B-321-165X16 is a high density BRIC12 matrix module with a size of 165x16 with 1-pole switching. It is part of a range of BRIC matrices available in 2, 4, 8 or 12-slot formats to suit high performance PXI matrix requirements and is constructed using instrumentation quality reed relays.
-
Product
PXI 12-Slot BRIC Matrix, 294x12 1-Pole (7 sub-cards)
40-558-121-294X12
Matrix Switch Module
The 40-558-121-294x12 matrix is part of a range of BRIC ultra-high-density large PXI matrices are available in 2, 4, 8 or 12-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI/PXIe RF Matrix, 16x2, 100 MHz, 75 Ω SMB With Loop-thru
40-728A-101-L
Matrix Switch Module
The 40-728A-101-L (PXI) and 42-728A-101-L (PXIe) are 16x2 75 Ω RF matrices with SMB connectors and Y-axis loop-thru. The 4x-727A/728A/729A range are high density RF matrix modules suitable for switching up to 300 MHz in 50 Ω or 100 MHz in 75 Ω. They are available in 50 Ω or 75 Ω versions with SMB connectors or in 50 Ω versions with a multiway connector.
-
Product
LXI Single 24x8 Video Matrix, SMB (50R)
60-711-711
Matrix Switch Module
The 60-711 is a Dual 24x8 Video Matrix Module suitable for switching frequencies up to 25MHz. It has a characteristic impedance of 75Ω with the option of SMB or MCX connectors or, with a larger case size, BNC connectors.
-
Product
PXI Dual 2x2 RF Matrix 2.5GHz 50 SMB
40-877-002
Matrix Switch Module
The 40-877-002 is a 50Ω 2x2 RF matrix with 2 banks in a single PXI slot. Loop-thru connections are provided on both the X and Y axis allowing the attachment of terminations for unused signals or for expansion to other matrices. Larger matrices are easily built with varied X and Y dimensions, such as 8x2 and 4x4 using multiple 40-877 modules. The module has low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost.
-
Product
8-Slot BRIC, 126x12, 1 Pole, PXI Matrix (3 Sub-cards)
40-559-801-126x12
Matrix Switch Module
This range of BRIC ultra-high-density large PXI matrices are available in 2, 4 or 8-slot PXI sizes to suit all high-performance matrix requirements and are constructed using Pickering Electronics' 4mm x 4mm instrumentation quality reed relays.
-
Product
PXI Single 24x8 Matrix, 2 Pole Switching
40-521-022
Matrix Switch Module
Typical applications for this high density matrix include signal routing in Functional ATE and data acquisitionsystems. These PXI matrix cards are constructed using high reliability rutheniumelectro-plated reed relays, offering >10e8 operations to give maximum switchingconfidence with long life and stable contact resistance. Larger matrices may be constructed by Daisy Chaining the common signals from multiple PXI modules. For example, 7 PXI modules will form a 168x8 Matrix, a total of 1344 crosspoints in a 7-slot PXI Chassis. All 40-521 series modules are fitted with reed relays (ruthenium sputtered type), these offer very long life with good low level switching performance and excellent contact resistance stability.Spare Reed Relays are built onto the circuit board to facilitate easy maintenance with minimum downtime.
