PIN Diode Switches
-
product
PXI Hex SPDT RF Switch 3GHz 50 SMB
40-870-006
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
product
SSP Switch Probes
Current Rating (Amps): 5Average Probe Resistance (mOhm): 50Spring Force Remark: Force at switch point: 2.36 (66)Test Center (mil): 187Test Center (mm): 4.75Full Travel (mil): 150Full Travel (mm): 3.81Recommended Travel (mil): 100Recommended Travel (mm): 2.54Mechanical Life (no of cyles): 100,000Overall Length (mil): 1,210Overall Length (mm): 30.73Switch Point (mil): 25Switch Point (mm): 0.64
-
product
PXI Solid State Switch Module, 6xSPST, 10 A
40-182A-011
The 40-182A-011 has 6 off high current SPST switches in two PXI slots and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
PXI Fault Insertion Switch, 7-Channel, One Fault Bus, 20 A
40-193A-001
The 40-193A-001 is a 7-Channel Fault Insertion switch with one fault bus, designed for the simulation of fault conditions in automotive systems. The module is capable of switching current up to 20A.
-
product
Switch Modules - 8 Single Pole, Form C, Discrete Power Relays which are Wired & Controlled Individually
JX8/KCP
This module has 8 single pole, Form C, discrete power relays which are wired and controlled individually. The relays can be externally wired to make any configuration needed. Use as individual A-B relays or use them to drive external relays, solinoids, or any external device. Screw Terminal Connectors and Armature power relay for switching up to 8 Amps of DC or AC current.
-
product
High-Power PXI Multiplexer Switch Modules
Our High-Power PXI Multiplexer Switch Modules are based on electro-mechanical and solid state relays capable of switching currents of up to 40 Amps. Each module supports one or more multiplexer channels between one input/output terminal and a selection of output/input terminals. To reduce through path resistance, most of these multiplexers do not include isolation relays.
-
product
PXI 3-Channel 10A Solid State SPST Switch
40-182-012
The 40-182-012 has 3 off high current SPST switches in one PXI slot and is part of our range of high power solid state switching solutions. Each SPST switch uses a fully isolated solid state relay which has been designed to offer fast operation under hot switching conditions and high inrush current with no operational life degradation. Each SPST switch can support 10A of continuous current and switch up to 200V signals. The switch can sustain inrush currents in excess of 50A. AC or DC signals can be switched since the switch is polarity insensitive.
-
product
PXI Solid State Switch Module, 3xSPST, 10 A, Hardware Interlock
40-182A-012-HI
The 40-182A-012-HI has 3 off high current SPST switches with hardware interlock in one PXI slot and is part of our range of high power solid state switching solutions.
-
product
PXI Triple SPDT RF Switch 3GHz 50 SMB
40-870-003
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 40GHz, 50Ω, SMA-2.9
40-782B-541
The 40-782B-541 (PXI) and 42-782B-541 (PXIe) single transfer switches are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50Ω and a maximum operating frequency of 40GHz. Connections are made via front panel mounted high quality SMA-2.9 coaxial connectors.
-
product
PXI SPDT Switch: 64-ch, 100 Vrms / 1A, Reed Relays
M9131A
The M9131A is a high-density, general purpose switch with 64 independent, single-pole, double-throw (Form C) switches in a single PXI module. This module can be used to cycle power to products under test, control indicator and status lights, or actuate external power relays and solenoids. The high-speed, long-life reed relays can handle 100 Vrms and 1 A, with up to 3 W maximum power. Choose from the durable connector block or standard cable connections.
-
product
PXI Hex SPDT RF Switch, 8GHz 50Ω SMA, Terminated
40-880A-003
The 40-880A-003 is a hex SPDT 50Ω RF switch with 8GHz bandwidth. The 40-880A range of SPDT switches have automatic termination of unused signals and are available as a dual switch in a 1 slot PXI module, a quad switch in a two slot PXI module or hex and octal switches in three slot PXI modules
-
product
Standard 1.10 (31.18) - 4.80 (136.00) Switch Probe
TSP100-H150-1
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
Switch Modules - 26 Two POle Relays Arranged as Two Separate 8x1 Multiplexers
JX16/L2
This module has 16 two pole relays arranged as two separate8x1 multiplexers as shown in the figure to the left. The muxes may be operated and wired individually for up to 32 8x1's per chassis, or jumpered together to form 16x1's or jumpered to the backplane to form up to a 256x1 mux or two 128x1 muxes. It is available with Type S, M or LT reed relays.
-
product
PXI Hex SPDT RF Switch 3GHz 50 MCX
40-870-106
The 40-870 is a 50 RF Switch available with 3 or 6 separate SPDT relays in a single PXI slot. Both versions exhibit low insertion loss and VSWR through the use of modern RF relay technology at an affordable cost. The switch banks been carefully designed to ensure excellent and repeatable RF characteristics to frequencies of 3GHz. The injection of noise and unwanted signals into the signal paths of the 40-870 has been minimized by careful attention to the mechanical and electrical design.
-
product
PXI 9 x SPDT RF Switch 500MHz 50 Multiway Connectors
40-754-009
The 40-754 is a 50Ω High Density RF switch available with 17 or 9 SPDT relays in a single PXI module. The 40-754 is available with two connector options; an SMB connector that provides a frequency range of 1.2GHz (useable to 1.8GHz) occupying two PXI slots, or an MS-M RF multiway connector which limits the bandwidth to 500MHz but offers a high density solution occupying one PXI slot. The RF switch design is identical in each case.
-
product
PXI Solid State Switch Module, 6xSPST, 10 A, Hardware Interlock
40-182A-011-HI
The 40-182A-011-HI has 6 off high current SPST switches with hardware interlock in two PXI slots and is part of our range of high power solid state switching solutions.
-
product
Standard 1.10 (31.18) - 4.80 (136.00) Switch Probe
TSP100-H180-1
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
PXI Hybrid Single SP6T Switch, DC To 26.5 GHz, Terminated
M9157C
M9157C operates from DC to 26.5 GHz, providing a low-cost operation switching solution for measurement and automation of Automatic Test Equipment (ATE) systems without compromise in the RF performance. It is being used in applications such as ATE, RF communication and RF parametric measurements where a rugged switching module is needed for signal routing. Typical switching applications for multiport coaxial switches include signal routing to a single input to multiple instruments and routing of multiple input signals.
-
product
PXI/PXIe RF Switch, Dual SPDT, Terminated, 8GHz, 50Ω, SMA
40-880B-001
The 40-880B-001 (PXI) and 42-880B-001 (PXIe) are dual SPDT 50Ω RF switches with 8GHz bandwidth. The 40/42-880B range has automatic termination of unused signals and are available as a dual switch in 1 slot, a quad switch in a two slots or hex and octal switches in three slots.
-
product
PXI/PXIe MEMS Optical Switch, Dual Insert/Bypass, Single-Mode, 9/125 Fiber, MU Connectors
42-860A-322
The 40/42-860A-322 is a PXI/PXIe dual insert/bypass switch with MU connectors and is part of Pickering's range of PXI Fiber Optic MEMS Switching modules.
-
product
PXI Single Transfer Switch 40GHz 50Ω SMA-2.9
40-782-541
The 40-780 Microwave switching module consists of one, two, three or four changeover switches capable of switching frequencies to 18GHz (optionally to 67GHz) in 50Ω or 2.5GHz in 75Ω. The 40-782 module consists of one or two microwave transfer switches. It has a characteristic impedance of 50Ω and is available in versions with maximum operating frequencies of 18GHz, 26.5GHz or 40GHz.
-
product
High 1.80 (51.00) - 12.60 (357.00) Switch Probe
TSP138-FK300-3
Current Rating (Amps): 10Average DC Resistance lower than (mOhm): 20Test Center (mil): 138Test Center (mm): 3.50Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,760Overall Length (mm): 44.70Switch Point (mil): 67Switch Point (mm): 1.70
-
product
Keying Pin Kit, ISeries, Receiver And ITA
310113461
The iSeries keying pin kit includes a set of two hex keys. One hex key will allow 6 different options and two can provide 36 different keying options. The keying kit provides a way to isolate your connectors to prevent operational mismatch.
-
product
High 2.90 (82.20) - 12.60 (357.00) Switch Probe
TSP100-FK180-3
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
PXI Multiplexer Switch Module
PXI Multiplexer Switch Modules are ideal for high-channel-count applications that need to connect measurement or signal generation instruments to various test points on devices or units under test(DUTs or UUTs). PXI Multiplexer Switch Modules use a variety of relay types, including electromechanical armature relays, reed relays, field-effect transistor(FET) relays, and solid-state relays, each with their own benefits, allowing you to choose a multiplexer that fits your requirements. To program the switches, you can use the IVI-compliant NI-SWITCH driver software, complete with help documentation, example programs, and a soft front panel application for interactive control of switches. For intelligent management of complex switch systems, NISwitch Executive provides additional software tools to help you design, build, and deploy your switching system.
-
product
Alternate 1.10 (31.18) - 7.20 (204.00) Switch Probe
TSP100-J100-2
Current Rating (Amps): 5Average DC Resistance lower than (mOhm): 20Test Center (mil): 100Test Center (mm): 2.54Full Travel (mil): 197Full Travel (mm): 5.00Recommended Travel (mil): 157Recommended Travel (mm): 4.00Overall Length (mil): 1,990Overall Length (mm): 50.60Switch Point (mil): 59Switch Point (mm): 1.50
-
product
LXI High Voltage Switching - 10xSPST Plugin Module
65-233-904-HI
The 65-233-904-HI plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
product
1.5-m, 78-pin Dsub Cable
Y1137A
The Y1137A is a M/F twisted-pair cable with outer shield. The 300-V cable provides a direct connection for the Keysight multifunction switch / measure mainframe and modules. Some modules require two cables.
-
product
PXI/PXIe Microwave Transfer Switch, Single, 50 GHz, 50 Ω, SMA-2.4, Failsafe, Remote Mount
40-782B-551-E
The 40-782B-551-E (PXI) and 42-782B-551-E (PXIe) single failsafe transfer switches with remotely mounted relays are part of our range of PXI microwave switching modules. They have a characteristic impedance of 50 Ω and a maximum operating frequency of 50 GHz. Connections are made via front panel mounted high quality SMA-2.4 coaxial connectors.
