Vector Signal Transceivers
are a user-programmable FPGA controlling a combination of vector signal generator (VSG) and vector signal analyzer (VSA). programmable FPGA
See Also: Transceivers, Vector Signal, Optical Transceivers, Vector Signal Analyzers, Vector Signal Generators
-
Product
Signal, Module, Receiver, CASS, QuadraPaddle, 800 Position
510113138
Receiver Module
Signal, Module, Receiver, CASS, QuadraPaddle, 800 Position.Mating module is 510114131.
-
Product
Sarsat Distress Signal Fixed Receiver
406
-
We propose to use Sarsat Beacon Monitor 406 in seaport services, rescue marine centers, coast guard rescue centers or GMDSS rescue coordination centers. However, this system has various prospective effective use fields. SBM 406 is a wide range ground COSPAS-SARSAT signal receiver which allows to locate emergency rescue signals sent by any 406MHz beacon in local responsibility area. The device can be connected to PC or laptop, and this gives possibility to observe distress signals and beacon position data on monitor.
-
Product
Vector And Scalar Mixer/Converter Measurements
S93083B
-
The S93083B provides both fully calibrated vector and scalar measurements of mixers and frequency converters, with intuitive, easy-to-use user interface
-
Product
PCI & PXI Signal Amplifiers
-
Low power supply rails, a main part of the PXI, cPCI and PCI equipment, are a common cause for an inability to produce high voltage output. Tabor Electronics’ new amplifiers convert the supply rails to higher voltage suitable for signals up to 40Vp-p, thus solving thit problem.
-
Product
Spectrum Analyzers (Signal Analyzers)
-
Choose from advanced benchtop, handheld, general purpose, and scalable modular sprectum analyzers (signal analyzers), all with the broadest set of application-specific software. Advance your RF spectrum analyzer to the next level, spectrum analysis (signal analysis) has never been this easy.
-
Product
Spectrum And Signal Monitoring
-
Kratos Defense & Security Solutions, Inc.
With the rapid growth of satellite networks including VSATs, there is the potential for increased Radio Frequency Interference (RFI). Interfering signals can be periodic or occur at different frequencies over time, making the discovery and removal of these sources a significant challenge.
-
Product
Signal and Spectrum Analyzer
FPS
Spectrum Analyzer
The R&S®FPS is an exceptionally fast and compact signal and spectrum analyzer for performance oriented users. In production and in monitoring systems, only 2 HU of rack space are required – a reduction of 50 % compared with traditional instruments.
-
Product
Rubidium Standard with Optional DDS Signal Generator
1450B
-
The 1450B outputs can be configured as sine waves or square waves and can provide frequencies of 10MHz, 1MHz, 100kHz, 1pps or optional signal generator outputs. The signal generator outputs use direct digital synthesizer (DDS) technology and are confirurable from 100Hz to 171MHz. The 1450B also includes a 1pps input that can be used to discipline and automatically calibrate the 1450B. The 1pps input signal is typically obtained from an external device like a GPS frequency receiver/antenna. The Novatech GPS1 Smart Antenna with 1pps output is available as an accessory to provide a complete turnkey solution.
-
Product
Optical Signal Transmission
Analog
-
Used for oscillographing analog signals under EFT/EDS/RF interference.
-
Product
Signaling and Display Systems
-
*Display of analog process values*Display and monitoring of process values*Display and monitoring of pulse-shaped signals
-
Product
FMC Wideband RF Transceiver AD9371 Based
FMC-ZU1RF-A
-
Sundance Multiprocessor Technology Ltd.
The FMC-ZU1RF-A is a FMC for RF wireless communications applications based on the AD9371 component from Analog Device Inc (ADI).http://www.sundance.technology/wp-content/uploads/2018/01/FMC-ZU1RF-High-Res-Cutout-e1516095831285.jpgThis FMC is fully hardware and software compatible with the ADRV9371 evaluation board from ADI.
-
Product
Signal Integrity Test Products
RoBAT SCARA-TDR-M
-
*Fully automatic TDR tester for bare and assembled PCBs*2 – 24 Port Ultra-compact TDR units*Full range of TDR tests and measurements available*100% test in a production environment*Custom modules with automatic tool changer
-
Product
Offline Signal Processing & Analysis Software
Signal Processing - DX
-
APEX Turbine Testing Technologies
DX is an easy to use, graphical, signal processing environment that simplifies analysis and reporting of dynamic data. DX includes everything needed to process data for a variety of applications and industries in a very intuitive, drag-and-drop user interface. Generate fully-interactive engineering plots from one or more tests and create reports in just a few mouse clicks.
-
Product
2U Rack Mount Digital Signal Processor
-
Intel based Digital Signal Processing Computing System. Designed for radar or imaging applications.
-
Product
Converter Signal Amplifier – 0…10 Vdc – DIN Rail
HD978TR4
-
Configurable signal converter amplifier with 0…10Vdc (10…0Vdc) output. Input range -10 ..+60 mVdc. Standard configuration 0…20 mVdc.
-
Product
2-Channel 400MHz DDS Signal Generator
2940A
-
The 2940A is a two-channel 400MHz DDS Signal Generator that generates two independent sine wave output frequencies simultaneously from 200kHz to 400MHz in 1Hz steps. A Clock Generator configuration with ECL or LVDS clock outputs is also available. The 2940A is lockable to an external frequency standard or is used with its internal TCXO. Optional internal amplifiers and 60dB step attentators available. Set all parameters with front panel controls and LCD display or by computer using the RS232 serial interface. All settings can be saved into non-volatile EEPROM memory upon power down. Windows software included.
-
Product
Complete TAP Signal Isolation for Corelis Boundary-Scan Controllers
ScanTAP IsoPod
-
The Corelis ScanTAP IsoPod™ is an add-on accessory that provides a galvanic isolation barrier between the target system and the boundary-scan (JTAG) controller hardware. While the Corelis boundary-scan controllers are highly robust and reliable, the complete electrical isolation helps prevent damage to the controller from harsh electrical environments where over-voltage and over-current can damage components.This Corelis ScanTAP IsoPod was designed to add an additional layer of protection with minimal cost and effort. Open the box and plug it in; everything just works.
-
Product
Sensor Signal Emulator
-
This Sensor Signal Emulator is specially designed for Automotive Technicians to troubleshoot electrical control systems problems in the car. It simulates the signals generated from different sensors in the vehicle and the ECU which enables technicians to pinpoint the actual faults in the electrical control system in cases of doubt over their judgment of replacing the sensors or the entirety of the connecting wires to the ECU.
-
Product
Ocean Signal RescueME PLB1 (Personal Locator Beacon)
RescueME PLB1
-
The RescueME PLB1 is the world's smallest 406mhz & GPS enabled PLBOperation of the rescueME PLB could not be simpler. To activate the PLB: Pull the retractable antenna out by its end tab, flip open the spring loaded cover over the activation button, hold the button for 1 second until the lights blink. Visual instructions are clearly printed on the case. When activated, the rescueME PLB1 will transmit accurate position data from its 66 channel GPS for a minimum of 24 hours while the integrated strobe light ensures maximum visibility.Ocean Signal has ensured that rescueME, like all of its other safety products, exceeds statutory requirements. RescueME PLB provides an incredible 7 year battery life, and is covered by a 7 year warranty. Even after more than 24 hours of continuous operation, and when the battery power is insufficient to transmit the satellite signal, the PLB1's homing beacon and strobe light will continue to operate. This high intensity strobe light features a molded lens to enhance the visibility of its efficient LED and it gives a powerful 1 candela light emission.Self-test of the PLB can be carried out with a simple button press with the start of test and results clearly indicated by a green flashing light. The antenna is easily extended like a normal tape measure and can be retracted using the winding mechanism on the top of the unit. This unique feature greatly facilitates user training and familiarization as it is not a one time deployable antenna similar to existing PLBs.rescueME comes with a snap-in mounting bracket and universal rubber mounting strap which can be fitted permanently or with each use. It is also supplied with a detachable flotation lanyard to accommodate all scenarios out of the box.
-
Product
RTM Discrete Signal Conditioning Board
MS 3632I
-
CPCI Rear IO Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3639i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
Signal Lab
-
Quick-start features for Bluetooth, DECT, GSM, NADC, PDC, PHS, TETRA, WCDMA 3GPP, Worldspace, TFTS. Graphical representation for vector diagram, signal spectrum, and I/Q dependence on time
-
Product
Load Cell Amplifier Signal Conditioner with Removeable Terminals
MODEL LCA-RTC
-
The LCA-RTC Module provide low-cost, dedicated signal conditioning for a single bridge type load cell or torque sensor. Model LCA-RTC comes with removable screw-clamp terminal connectors, which accept wires without soldering.On- board jumper selections include sensitivities from 0.5 mV/V to 10 mV/V, bandwidths from 100 Hz to 30 kHz, and amplified outputs of 0 to ±5V, 0 to ±10V, 0-16 mA, 0-20 mA or 4-20 mA. Zero and span adjustments are via precision 25-turn low-tempco metal film potentiometers.The units can be operated next to the sensor with 4-wire hookup or at distances up to 1 km (3300 feet) with 6-wire hookup. An onboard 87.325 kΩ resistor allows easy shunt calibration at the push of a button. Provision is also made for a user-furnished calibration resistor. Power requirements are 11.8 to 26V DC with load currents from 10 to 60 mA, the latter applying when the unit provides 10V DC excitation to a 350 ohm load cell and delivers a 20 mA analog output.
-
Product
Signal Amplifier
9100A
Amplifier
Model 9100A was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It is built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
Product
Suitable For Current Or Voltage Process Signals
SEM1600VI
-
The SEM1600VI is a “smart” powered isolator/conditioner that accepts any voltage signal between (-50 and 50) V dc or any current signal between (-50 and 50) mA
-
Product
Streamline Vector Network Analyzer, 100 KHz To 26.5 GHz, 2-port
P9375B
Vector Network Analyzer
Compact, faceless, vector network analyzer (VNA). Affordable full two-port VNA which dramatically reduces your size of test. Up to 26.5 GHz.
-
Product
Signal Generators
-
Dongguan Longwei Electronic Technology Co., Ltd.
An electronic device that generates repeating or non-repeating waveforms used to test and evaluate electronic test equipment.
-
Product
Sources Signal Generators
-
PGP Electronics Private Limited
Manufacturer of a wide range of products which include Function Generators, DC Regulated Power Supplies, Decade Boxes, Pulse Generators and DC Voltage/Current Source Meter.
-
Product
"Signal Transporter"
LTX-5510
-
The LTX-5510 enables precise conveyance of analogue plus four channels of digital information over fibre optic links ranging from meters to more than 10 kilometers. Incoming analogue data is digitised to 12-bit precision at 50 mega-samples per second and transmitted over optical fibre at a 1 Gb/s data rate.?
-
Product
High-Speed Signal Recording Systems
System
GaGe has a long history of providing high-speed, real-time signal acquisition, processing, and recording systems on PC-based platforms. This expertise saves customers time and eliminates uncertainties and risks with self-integrated systems.
-
Product
Signal Conditioners
SC-1300
-
The SC-1300 family of signal conditioners can convert the most commonly used process signals into conditioned current and voltage outputs, needed for control systems and monitoring devices. Dedicated functionality and isolation from control systems improves reliability.
