Powder
-
Product
Model DG-9 (Universal Voltage)
DA8-G9-UNIV
-
Designed for semi-solids; powdered, granular or textile materials; and pliable sheets in rolls or stacks. Optional needle electrodes and sensitivity modules which allow for a wide range of moisture measurements. Rechargeable NiMH batteries save hassle and money of battery replacement.
-
Product
Needle Microprobe
MT-26/4HT
-
Fast-response 26 gauge needle probe, (needle length is 4 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Compare Color Measurement Instrument
DRK8636
-
Shandong Drick Instruments Co., Ltd.
WSL-2 Comparison of color measurement instrument (tint meter) is a visual color measuring instrument, which uses a special color internationally recognized a Lovibond color scale to measure a variety of liquids, gels, solids, and powder samples of color. The instrument has a simple structure, convenient operation characteristics, commonly used in color measurement grease, paint, plastics, jam, textiles, food, and other different substances. Lovibond color scale is a special color units, it is a very simple and quite perfect digital color language. Therefore, it can be easy and intuitive to measure a variety of colors, easy to master. Lovibond color measurement instrument has been accepted by many countries in the world,the increasingly widespread application.
-
Product
Moisture Measurement
-
Moisture: The presence of moisture within a material will result in poor adhesion, premature coating failure and poor appearance. For example, applying a powder coating to a damp wooden panel will cause steam to be created when the panel passes through the curing oven, thus causing damage to the coating. It is not sufficient to simply ensure that the surface is dry by touch. The surface of the substrate is often the driest point due to evaporation. It is important to establish the moisture content within the substrate itself. The moisture measurement can either be taken using a Pin moisture meter or Pinless (Contact-Type) moisture meter.
-
Product
Frequency Conversion Rotating Magnetic Fla
MT-2XCF
-
MITECH MT-2XCF rechargeable frequency conversion rotating magnetic flaw detector is based on principle that the leakage magnetic field can absorb the magnetic powder. Make use of magnetic yoke magnetized the workpiece of ferromagnetic material. If there has defects it will produce leakage magnetic field that will adsorb magnetic powder. We could detect the flaw by observing the density of adsorption magnetic powder. It adopts large capacity lithium battery. By the inverter and the phase shifted signal processor to provide power for the detector, it solves the shortcomings of traditional magnetic particle detector relying on the 220V power supply. It has low power consumption and can continuous work for more than 6 hours. And the battery can be charged when the detector is on and off. Especially suitable for the field testing. It can choose the current frequency according to the flaw depth with unique frequency conversion communication design, that improve the detection sensitivity. It’s widely used in aircraft manufacturing, boiler and pressure vessels and other fields. It is a necessary professional precision instrument of quality control, in-service safety monitoring and life assessment.
-
Product
Enclosure, 9025, Hinged Cover, 15" Depth
410112823
-
Housing: Material = .06" Aluminum, Finish = Powder Coat Black.Cover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize.
-
Product
Apparent / Bulk Density Tester
Bulk Density Tester Series
-
The Apparent Density Tester - Bulk Density Tester series testers are used to measure apparent density, bulk factor, and where applicable, the pourability of plastic materials such as molding powders. There are three methods according to ASTM D 1895 that are applicable to various forms of these materials that are commonly encountered - from powders and granules to large flakes and cut fibers. The apparatus consists of a measuring cup which is polished inside and a funnel.
-
Product
Enclosure, 9075, Removable Cover, 6" Depth
410112561
-
Enclosure, 9075, Removable Cover, 6" DepthThis 9075 ITA enclosure includes four handles for handling convenience and a removable cover secured by 14 fasteners (included) for easy internal wiring access. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Enclosure, S6, 2U Height, 12" Depth
410112703
-
Enclosure, S6, 2U Height, 12" Depth Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Heavy-Duty Roll Around Cart
6038C
-
• Powder Coated Steel with Universal Mounting Top Plate Adjustable for Easy Visibility • 2 Storage Trays – top tray for battery tools, bottom tray accommodates bench-top battery charger• Heavy Duty wheels• Made in USA of US and Global Components
-
Product
Strain Relief Plate, Receiver, I2 Micro ICon
310113559
-
The i2 Micro iCon strain relief plate attaches to the wiring side of the receiver and can be secured before receiver installation. The strain relief plate is made of aluminum and is black powder coated. It includes 4 wire ties.
-
Product
Dynamometer Power Supply
DES Series
-
The DES 310 and DES 311 power supplies are suited to the entire range of Magtrol's Eddy-Current and Powder Brake Dynamometers. To avoid any disruption of the surrounding electronic modules, the DES 310 / DES 311 supplies are fitted in an industrial housing made of extruded cast aluminum. This housing must be installed directly on the test bench, as near to the dynamometer as possible.
-
Product
Level Control Loop Trainer Model
ULP-24P & ULP-24C
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Level Control Setup comprises of acrylic measuring tank fitted with Level transmitter, control valve, I to P converter, source tank with water pump and necessary flexible piping for water circulation. The system is mounted on a table top powder coated metal frame. Level transmitter is of capacitance or DPT type sensor. The electronic panel comprises of ADC and DAC card with RS-232 interfaces.
-
Product
CompactPCI Serial, 5 Slots, SSR, 4U, 35HP, 290mm
435V0-E05R-25FA1-000
-
CompactPCI Serial System with 5 Slots: 4x CompactPCI-S.0 Peripheral Slots and 1x CompactPCI-S.0. System Slot on the right side of the system platform. 1x 250W ATX, air-cooled with fan fix-mounted and powder coated.
-
Product
Cupping Tester
PCE-CPT 20
-
PCE-CPT 20 is a cupping tester, or coating flexibility tester, used for testing the adhesion, elongation and deformability of paints, lacquers, varnishes, powder coatings and other surface coatings on metal sheets. Used in manufacturing production, paint shop and quality control applications, the PCE-CPT 20 cupping tester aids in determining coating strength, durability and elasticity. A mandatory test in Qualicoat and QIB accredited quality control laboratories, a cupping test, also referred to as an Erichsen test or dent test, uses a spherical punch to deform a sample. This deformation results in a cup-like bulge. When using the PCE-CPT 20 to perform a cupping test in accordance with the ISO 1520 standard, the sample should be placed coating side up so that the 20 mm spherical punch presses against the uncoated underside of the metal sheet. The cupping test is terminated when small cracks and/or detachments are observed on the bulged part of the sample. The PCE-CPT 20 cupping tester's easy-to-read display shows the bulge deformation distances that can be used to determine the coating's flexibility rating.
-
Product
Control Valve Characteristics Trainer (ULP-23)
-
Unitech Scales And Measurements Pvt. Ltd
Control Valve trainer comprises of globe type control valve (½”) with diaphragm type Pneumatic actuator. The control valve is of linear / Equal% type. The setup comprises of water pump with necessary flexibal piping, Water tank, I to P converter, Air regulator fitted on a table top powder coated metal frame.
-
Product
Enlarge Environmental Chamber
REXMED REC-450
-
MOD. REC-450, AC 230/380/415V, 1/3 phase, Environmental chamber, HS CODE: 841989, UNCCS CODE: 484384, UMDNS CODE: 16327, Main construction: SS304, Interior: SS304, Exterior: SS304 powder coated, Insulation: Rigid polyurethane foam and glass wool, Controller: Fix point PID controller, temperature ˚C/PV and ˚C/SV, humidity %/PV and %/SV display and setting, Temperature range: -40˚C~100˚C, Humidity range: 20%RH~98%RH, Constancy: ±0.3˚C ±2.5%RH, Uniformity: ±1˚C ±3%RH, Temperature and humidity sensor: PT 100Ω, Temperature and humidity audio and visual warning and OFFS correction setting, Temperature heater: 1.5KW X 2pcs, Humidity heater: 2.5KW X 1pc, Heat up transition time: -40˚C~100˚C within 45 min, Refrigeration system: Air cooled, single stage, Cooling compressor: Bristol hermetic compressor, Cooling capacity: 3,644 Watts, 12,433 BTU/hr, 3,140 Kcal/hr, Cool down transition time: 20˚C~-40˚C within 50 min, Safety devices: No fuse breaker, refrigerator over load relay, refrigeration high pressure switch, over temperature protector, protection relay, protection fuse, water level control and overheat protector, Chamber: L60 X W80 X H85cm, Capacity: 408L, chamber with key lock, with lamp (DC 12V 50W) X 1pcs and double glass viewing window, testing cable port with cover: Ø25mm, 4 castors, W/S: shelf X 2pcs, standard testing wet cloth X 5pcs, PCV water container X 1pc
-
Product
Hybridization Oven
REXMED ROV-200
-
MOD. ROV-200, AC 110/230V, Plug type: , Hybridization oven, HS CODE: 841780, UNCCS CODE: 484352, UMDNS CODE: 14410, Main construction: powder coated steel and SS304, Controller: Microprocessor based PID controller, water proof keypad with timer, ˚C/PV and ˚C/SV display and setting, Timer: 9999/min, 9999/hr, Timer has DELAY_ON and DELAY_OFF function and at the end of operation audio and visual warning, Working range: Ambient +5˚C~85˚C, Stability at 37˚C: ±0.1˚C, Sensor: PT 100Ω, Temperature audio and visual warning for AL-H and AL-L and OFS correction setting, Heater: 1KW, Shaking timer: 999/min, 999/hr, shaking timer can be set in second, minute or hour function and at the end of operation audio and visual warning, Motor: Noiseless powerful brushless induction motor 15W, Rotation: 5~60rpm adjustable, Rotator: for 8pcs(optional), Reciprocal: 5~60rpm adjustable, Platform: L30 X W18cm(optional), Rocker: 5~60rpm adjustable, Platform: L29 X W22.5cm(optional), Chamber: L35 X W25 X H25cm, Capacity: 21.9L, chamber with glass viewing window, Optional: Rotator for 8pcs X 1set, reciprocal platform (L30 X W18cm) X 1set, rocker platform (L29 X W22.5cm) X 1set
-
Product
Moisture / Solids / Analyzer
Smart 6
-
The SMART 6 can determine the moisture content of any product, wet or dry. Samples such as solids, powders, slurries, non-polar or temperature-sensitive samples can all be analyzed with greater accuracy and speed.
-
Product
Enclosure, G18, Hinged Cover, 8" Depth
410112668
-
Enclosure, G18, Hinged Cover, 8" DepthHousing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Low cost EDXRF Elemental Analyzer
NEX QC+ QuantEZ
-
Applied Rigaku Technologies, Inc
As a premium low-cost benchtop EDXRF elemental analyzer, the Rigaku NEX QC+ QuantEZ delivers wide elemental coverage with easy-to-learn Windows®-based QuantEZ software. Non-destructively analyze from sodium (Na) through uranium (U) in almost any matrix, from solids and alloys to powders, liquids, and slurries. The 50 kV X-ray tube and Peltier cooled silicon drift detector (SDD) deliver exceptional short-term repeatability and long-term reproducibility with excellent element peak resolution. This high voltage capability, along with multiple automated X-ray tube filters, provides a wide range of XRF applications’ versatility and low limits-of-detection (LOD).
-
Product
Process Spectrometer
QualitySpec® 7000
-
Analytical Spectral Devices, Inc.
The QualitySpec® 7000 process spectrometer is ideal for measurement of process materials transported on conveyance systems. The system is designed for continuous measurement of solids, powders and blended materials, providing multiple measurements from a single point.
-
Product
Enclosure, 9025, Removable Cover, 8" Depth
410112415
-
Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Analytical Services
-
IGC: Inverse Gas Chromatography; Understand surface energies, polarities, acid/base properties and nanomorphology on powders and fibers. ToF-SIMS: Time-of-Flight Secondary Ion Mass Spectrometry. Localize your molecules at the first nanos! 2D imaging with resolution up to 200 nm. Highest sensitivity up to 10 ppm. CM: Quarz Crystal Microbalance In-situ observation of thickness and stiffness of any films in liquid environmentSEM: Scanning Electron Microscopy Images say more than words, especially with an artistic eye XPS/ESCA: X-ray Photoelectron Spectroscopy/Electron Spectroscopy for Chemical Analysis.
-
Product
Silicon Inspection System
NIR-01
-
The NIR-01 imaging system is made of CNC engineered Aluminium alloy. The suruface protection is powder painting and electrolitic oxidation on pure aluminium surfaces. The frame of the system is a high quality industrial design. All components are designed for long term heavy usage with minimal maintenance needs. Electrical components are also selected for stability and durability. The block like electronics gives the advantage of easy and quick repair.
-
Product
Enclosure, G12, Front Mount, 7" Height, 12" Depth
410112757
-
Enclosure, G12, Front Mount, 7" Height, 12" Depth Includes hinged cover. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Particle Size Analyzers
Mastersizer Range
-
The Mastersizer range of laser diffraction particle size analyzers set the standard for delivering rapid, accurate particle size distributions for both wet and dry dispersions. From assessing product uniformity and solubility, through to optimising packing density to improve final product performance and controlling powder flowability to increase manufacturing efficiency, particle size analysis is critical to understanding and controlling a wide range of properties. The Mastersizer range, with its intuitive software and industry-leading design and ergonomics, enables users to make these particle sizing measurements fast and routine.
-
Product
Needle Microprobe
MT-26/6HT
-
Fast-response 26 gauge needle probe, (needle length is 6 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Enclosure, G12, Hinged Cover, 12" Depth
410112665
-
Enclosure, G12, Hinged Cover, 12" Depth Approximate weight- 5.5 lbs. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Dynamic Wettability Tester
6200TN
-
This is a dynamic wettability tester that uses a high-performance electronic balance to evaluate temporal changes in buoyancy and wetting (contact angle) that are successively received when various solid pieces and powder samples are immersed in liquid. Information such as dynamic and static contact angles, surface tension, and density can be obtained, and it supports various sample forms such as flat plates, fibers, and powders
