RF Box
A space surrounded by an electromagnetic radiation barrier
See Also: Boxes, Decade Box, Anechoic Boxes, Black Box, Breakout Boxes, Hot Box, White Box, Shielded Box, Programmable Resistance Box
-
Product
RF Frequency Mixers
-
LO power levels from 3 to 27 dBmExcellent unit-to-unit matchingHermetically sealed LTCC packagesLowest cost models in the industry
-
Product
Expandable Embedded Box IPC With Intel® Celeron® J1900
UNO-3272G
-
Intel® Celeron® J1900 2.0GHz processor with 4GB DDR3L memory3 x USB2.0, 1 x USB3.0, 2 x RS232/422/485, 2 x RS2322 x 10/100/1000BASE-T EthernetVGA, HDMI support 2 x independent displaysOptional Digital I/O support for sensing and controllingDedicated TPM2.0 microcontroller designed for hardware securityFlexible system I/O expansion by iDOOR technologySupport diverse fieldbus protocol by iDOOR technologyDual Power input for power redundancy
-
Product
CWDM Mux/Demux in LGX Box(4,8,16,18-Channel)
-
Flyin Optronics’ Coarse wavelength division multiplexer (CWDM Mux/Demux) utilizes thin film coating technology and proprietary design of non-flux metal bonding micro optics packaging. It provides low insertion loss, high channel isolation, wide pass band, low temperature sensitivity and epoxy free optical path.
-
Product
Decade Box, Calibrated W/Data, Resistance, 7, 1ohm to 11.11111Mohm, 1 %
72-7270 CAL D
-
The 72-7270 CAL D from Tenma is a resistance decade box. It is ideal for service, prototype and experimental use. This useful tool may be set resistance value from 1 to 11,111,110 ohm in one ohm increments. The decade accuracy is ±1% resistors used throughout. It has weight of 320g/0.70lb and dimension 14.7cm × 11.7cm × 5.5cm (5.79" × 4.61" × 2.16"). It is typically used in general applications, troubleshooting, maintenance, education and vocational training, production line testing, radio and TV services, working standards, research design & develop, physics laboratory work.
-
Product
FMC L-Band RF Receiver
-
Sundance Multiprocessor Technology Ltd.
The Creonic L-band RF receiver FMC card allows to receive RF signals between 925 and 2,250 MHz. It is ideally suited for satellite communication with standard satellite dishes since it includes a DiSEqC driver IC for LNB controlling. The board allows to build receivers with symbol rates of up to 100 Msymbols/s. Due to the low-pin-count (LPC) FMC connector it can be used with any FMC carrier board that supports VADJ=1.8V. The card will be available from Q2/2017.
-
Product
Drone Detection RF Monitoring System
-
Shenzhen Tangreat Technology Co., LTD.
Drone Detection RF Monitoring System by Tangreat
-
Product
RF Test Benches
-
FIME laboratory equipment qualified for RF testingValidate the analogue behaviour of RF devices with a single set of laboratory tools and services before seeking contactless Level 1 type approval or launching mass production. FIME RF test benches are built for RF testing of: EMV contactless cards and readers; ICAO e-passports and readers; ISO devices (PICC and PCD), HF and UHF RFID tags and readers.
-
Product
Quickly Upgrade RF ATE Testers
MP5800 / MP5806
-
*MP5800 Quickly Provides 3380 / 3650 RF ATE Test Capabilities*MP5800 and 3380/3650 hardware and software are fully integrated*Provide complete and user-friendly RF / Digital debug tools*Provide a complete solution for IOT applications*Provide API for production automation software*Integrate Zimmer 3380/3650 to provide RF/Digital comprehensive ATE test solution
-
Product
Optical Switch Boxes
-
An optical switch box is needed so that automated test platforms can permit the system to measure the performance of transmitters and receivers at multiple wavelengths or channels. The MLO4034 Optical Switch Box incorporates a WDM demultiplexer, integrated power meters, variable optical attenuators, and optical switches to form an integrated switch matrix. It enables receivers and transmitters to be tested at up to four wavelengths or channels.
-
-
Product
RF Power Sensors
-
Berkeley Nucleonics Corporation
an instrument, which can measure the electrical power mostly in the range of 100 MHz to 40 GHz.
-
Product
RF Cable Assemblies
-
Radiall's extensive range of RF cable assemblies features outstanding electrical performance, low loss and high frequency. The range includes flexible, semi-rigid, corrugated and hand-formable cable assemblies with a combination of RF cables and connectors optimized for each market or application. Custom RF cable assemblies are also available.
-
Product
RF Ports Alignment Software
-
With the R&S®RF Ports Alignment software together with the option R&S®SMW-K545, Rohde & Schwarz provides a standard and tailored solution for calibrating amplitude, time and phase of multi-channel SMW setups. The RF Port Alignment automatically collects the gathered correction data for the multi-channel setup using a connected vector network analyzer such as the R&S®ZNA or R&S®ZNB. Thanks to an intuitive graphical user interface the test engineer is guided through the calibration procedure step-by-step in a convenient way. With a calibrated multi-channel setup, tests of advanced systems in wireless communication or of radar receivers can be performed straightforward.
-
Product
1203c Broadband RF Distribution
-
Precise Time and Frequency, Inc.
The ptf 1203C Broadband RF Distribution amplifier provides high performance frequency references for laboratory or system use.The ptf 1203C uses two stages of input signal buffering to distribute the input signal to 12 separate outputs, and insure maximum isolation between individual output signals.
-
Product
Signal Conditioning and RF Distribution
-
CAES provides high performance signal conditioning and RF distribution solutions such as switch matrices for the EW, missile, radar, communications and space markets. Our custom designs offer high speed switching, low insertion loss, low harmonic level and excellent isolation.
-
Product
PXI Single RF Attenuator, 2.3GHz
41-181-021
Attenuator
The 41-181 Programmable Attenuator Module is available with either one or two independently programmable attenuators in a single width 3U PXI module. Each attenuator uses high reliability mechanical switches to operate binary weight attenuator pads, providing attenuation values from 0 to 63dB in 1dB steps. Attenuator operating time is typically just 5ms, ensuring fast setting times.
-
Product
ECM Noise Under RF Test System
BK8020
-
The BaKo Type BK8020 ECM Noise Under RF Test System tests microphones under RF noise, using a ‘Direct Injection Test’ in the frequency range of 5MHz~2.5GHz with an amplitude modulated (AM) disturbance signal of 1kHz. You run the system using the controlling PC, which allows automatic configuration and which runs the test sequence automatically. When you finish testing, you can print data as an MS Excel report or save it for comparison and analysis.
-
Product
RF Signal Detector
H-055DRV / 01019
-
The RF Signal Detector / 2G Cellular Phone Detector / Wireless Camera Detector / Bug Detector applies with fuzzy scanning technology to detect peeping cameras, tapping, cellular phones and other radio frequency devices.
-
Product
SMART III RF Moisture Sensor
-
Results are continuous, instantaneous and non-destructive. Used among diverse applications including gypsum, powdered and granular materials, agriculture and wood products. Monitor required to complete system. (Sold Separately): SMART III RF LED Screen OR Touch Screen
-
Product
50 Ohm SMB to SMA Adaptor Assembly
40-978-521-0.25m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
RF Connectors
MCX Connectors
-
The MCX (Micro Coaxial) series is available with 50 or 75 ohm options, and has broadband capability ranging from DC to 12 GHz. In addition, the MCX series features secure, fast and easy snap-on/ snap-off coupling. MCX connectors were introduced in the 1980s and conform to the European CECC 22220 spec.
-
Product
RF Attenuators
-
Amphenol RF offers a growing Attenuator product line to meet your attenuation needs. Amphenol RF attenuators are designed to offer flat attenuation over the designated frequency range and feature a microwave grade resistor that consistently reduces power. Hex flats on the body allow this attenuator to be easily torqued to the mating connector.
-
Product
RF Microwave Switching
Keithley S46
-
S46 and S46T Microwave Switch Systems are designed to simplify the automated switching needed to test a wide range of RF and telecommunication products and devices. The S46 can control 32 relay contacts in a package as small as a 2U high (3.5 in) full-rack enclosure. Choose the System 46T if your application requires a terminated configuration. It builds on the design technology of the unterminated System 46. The System 46T accommodates up to eight terminated SPDT coaxial microwave relays and four terminated multi-pole coaxial microwave relays.
-
Product
PXI 8x9 RF Matrix 500MHz 50 SMB
40-725-511
Matrix Switch Module
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
Product
6GHz RF Signal Generator
TGR6000
-
0MHz to 6000MHz frequency range10Hz setability, ±1ppm frequency stabilityLocking to external frequency standard-110dBm to +7dBm amplitude, 0.1dB stepsFast stepping sweep with dwell times down to 10msList sweep of up to 1000 points of amplitude vs frequencyUser compensation tables for specific test set-upsStorage for 12 generator set-ups and 16 sweep listsCompact half-rack 2U casing uses minimum bench spaceFull remote control through RS232, USB, LAN and GPIBSignificantly lower cost than other 6GHz generators
-
Product
RF Signal Generators
-
The G6 VSG from Transcom Instruments is a Vector Signal Generator that operates from 10 MHz to 6 GHz. It can simulate GSM, EDGE, CDMA, TD-SCDMA, WCDMA, CDMA2000, TD-LTE, FDD-LTE, NB-IoT, and LoRa base station signals for production and calibration of UE, chips. The signal generator has a dynamic range (power range) from -100 to 10 dBm and an in-built automatic gain control function. It is available in a module that measures 180 x 50 x 290 mm and is ideal for educational practices, wireless monitoring, mobile communication, aerospace and national defense industry in terms of research, manufacturing, testing and measurement, and electronic countermeasure.
-
Product
Modular Embedded Box PC With 11th Gen Intel® Core™ I CPU
UNO-2484G V2
Box PC
Intel® Core™ 11th i7/i5/i3 Processor with 8GB DDR4 3200Mb/s memory4 x GbE, 3 x USB 3.2 Gen2, 1 x USB2.0, 1 x HDMI 1.4, 1 x DP 1.4a, 4 x RS232/422/485Optional 2nd stack supports up to 2 x iDoor extension for expending wireless connectivity, industrial fieldbus or more I/OCompact fanless designRuggedized by zero cable and lockable I/O designSupports NVME storage with high data-transmission efficiency
-
Product
RF Shielded Test Enclosure, for Laptop Testing
JRE 2218
-
Breeze through laptop RFI and wireless tests with the 'bigger than-a-breadbox' 2218! Like its other brothers in the JRE test line, it features rugged welded aluminum construction with superb RF shielding effectiveness. Long life door gasket material along with double edge engagement not only provides solid RF shielding, but smooth trouble-free operation over its lifespan.
-
-
Product
75 High Isolation LXI RF Multiplexer
Multiplexer Module
Pickering's LXI high isolation RF multiplexers are suitable for switching 75 signals up to 1GHz - ideal for constructing complex microwave switching systems for many applications.
