Fibre Channel
Data transfer interface with speeds up to 2 Gigabit per second that maps to common transport protocols, i.e. IP and SCSI.
-
Product
16 channel 16 bit Digital to Analog Module
CPCI-DA16-2
Digital / Analog Converter
The CPCI-DA16 is a slave Digital to Analog board thatis managed by the host processor on the CPCI bus.The card contains a state machine that performs mostof the work of outputting data, in order to minimize theimpact to the HOST system.
-
Product
Dual Channel Gigabit Ethernet Test & Simulation Instrument for PCI Express
PCIe-DCE
-
Avionics Interface Technologies
Dual channel, high precision Ethernet Test Instrument
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode)STM62.5
40-860-512-M62.5
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Infiniium EXR-Series Oscilloscope: 500 MHz, 8 Channels
EXR058A
Oscilloscope
500 MHz on all 8 channels, options for 7 instruments integrated in one, hardware accelerated plotting, and fully upgradeable to 2.5 GHz
-
Product
8 Channel 100 MS/s 16-bit ADC
SIS3302
-
The SIS3302 is the 16-bit extension to our 100 MS/s digitizer family. It is the 2nd DDR2 memory based digitizer unit in the SIS33xx family. The board is used for the readout of high resolution detectors, accelerator controls and other applications.
-
Product
Signal Generator, 20MHz, 1 Channel, Arb.
33511B
-
With these signal generators, Keysight introduces the highly accurate True form technology. It generates true point-by-point arbitrary waveforms with ten times less jitter than current Direct Digital Synthesis (DDS) technology. The tracking filters allow for clean, alias-free signals. The devices have USB, LXI and GPIB interfaces for remote control from the PC.
-
Product
Dual-Channel, Tri-Port Per Channel, for Extended Cabling up to 20 Meters
FW1
-
The FW1 provides IEEE 1394 (Firewire) high-speed serial communications. The module is provided with a direct PCIe interface to the local (on-board) processor, or, an external host processor for board platforms that support external PCIe connectivity. These module(s) are not supported with the classic memory register-based NAIBrd Software Support Kit (SSK) API libraries. These communication function modules support device control and management via standard native OS (Linux) FireWire device driver.
-
Product
4, 8 and 16 Channel ARINC429 Test and Simulation Module
ANET429-x
-
The ANET429-x is a member of AIM’s Ethernet based modules for analysing, simulating, monitoring and testing ARINC429 channels.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 1 GHz, 4 Analog Channels
DSOS104A
Oscilloscope
The DSOS104A S-Series oscilloscopes have a bandwidth of 1 GHz, a 15” XGA capacitive touch screen, and a 10-bit analog-to-digital converter.
-
Product
IntegraVision Power Analyzer, 4 Channels, 3-Phase AC
PA2203A
-
Achieve better power analyzer accuracyAddress multiple test scenarios with the flexibility of wide-ranging, isolated inputsVisualize transients, in-rush currents & state changes with a high-speed digitizerAnalyze voltage, current and power in the time and frequency domains12.1" touchscreen
-
Product
Oscilloscope 70/100/200 MHz, 2 Analog Channel
DSOX1202G
Oscilloscope
The DSOX1202G oscilloscope provides 70, 100, or 200 MHz of bandwidth on 2 analog channels, and waveform generator.
-
Product
16/8 Channel 14 bit 500 MS/s Digitizer
VX1730 / VX1730S
-
The VX1730S comes in a VME64X form factor, with 16/8 input channels. The communication to and from the board is provided through the VMEBus and Optical Link interfaces. The VX1730S (previously VX1730) has also been upgraded, introducing a larger FPGA to accommodate more complex DPP algorithms and a new A/D converter for better stability which does not require temperature-related calibration.
-
Product
PXI 2 Banks of 80 Channel 1 Pole MUX
40-615-022-2/80/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration. Connections are made via a front panel 200-pin connector.
-
Product
PXI Dual 2 x 2 Fibre Optic (M Mode) SC M50
40-860-222-M50
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
4 Channel ADC FMC Module
ADCFN04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-ADCFN04 is a four channel Analog to Digital converter FMC which complies with VITA 57.1-2010. Each channel provides DC coupled single-end analog input and digital output with DC-250KHz sampling speed based on Linear Technology’s LTC2376-16. The output is 16-bit data and it can be obtained through SPI interface on LTC2376-16 from the FPGA on the FMC carrier board. One trigger input is provided for capture control.
-
Product
Multi Channel Bit Error Rate Tester
QSFP+ Tester Rx
-
You want to save time by measuring sensitivity on all four QSFP+ channels at the same time? Here we go: BERT + E/O converter + optical attenuator + optical power meter.Have this four times in two mainframes. Only one clock source is needed.Covers 16G FibreChannel and Infiniband FDR.
-
Product
16/8 Channel 14-bit 250 MS/s Digitizer
VX1725 / VX1725S
-
The VX1725S family comes in a VME64X form factor, with 16/8 input channels. The communication to and from the board is provided through the VMEBus and Optical Link interfaces. The VX1725S is a digitizer capable of recording waveforms along with performing advanced algorithms for online digital pulse processing (DPP). Utilizing DPP Firmware, users can acquire quantitative physical parameters (Integrated Charge, Pulse Shape Discrimination with very fine time resolution, Pulse Height Analysis) as well as read out waveforms with automatic pulse identification and baseline suppression on channel basis (Zero-Length Encoding and Dynamic Acquisition Window).
-
Product
PXIe 10GBase-T1 Ethernet MEMS Fault Insertion Switch, 8 Channel
42-205-008
Fault Insertion Unit
42-205-008 (PXIe) is a 8-channel fault insertion switches designed to simulate common faults on high speed two wire communication interfaces such as xBaseT1 Ethernet. They available with 4 or 8 channels of two wire serial connections and can be used for simulating faults on 10BaseT1, 100BaseT1, 1000BaseT1 and 10GBaseT1 Ethernet interfaces. Any wire can be set as open circuit and shorts can be applied across wire pairs. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to supply voltage or ground.
-
Product
Oscilloscope 110 GHz, 2 Channels
UXR1102B
Oscilloscope
The UXR1102B is the 110 GHz, 2 Channel, UXR-Series Real-Time Infiniium Oscilloscope.
-
Product
PXI Single 2 Channel Optic Mux FC/PC
40-855-112
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Form A Circuit Board 80 Channel, 300 VDC, 2 A
OTP2 module no.195
-
The 40-139 2A relay series is suitable for applications requiring medium power, high density switching. With a current capacity of 2 A and voltages up to 300 VDC / 250 VAC, it is suitable for cost-critical applications.
-
Product
PXI 10 Banks 0f 8 Channel 1 Pole MUX
40-615-021-10/8/1
Multiplexer Module
High density multiplexer modules featuring a wide range of switching configurations, especially useful where a large number of small multiplexers are required. Typical applications include signal routing in ATE and data acquisition systems. Each module is factory configured into one of the configuration modes. Connections are made via a front panel 200-pin connector.
-
Product
PXI Single 8 Channel Optic Mux FC/APC
40-852-018
Fiber Optic Switch
The 40-852-018 8-channel multiplexer is part of Pickering's range of PXI Fiber Optic MEMS Switching modules. They are available in many high density formats with a choice of different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Infiniium EXR-Series Oscilloscope: 4 GHz, 8 Channels
EXR408A
Oscilloscope
4 GHz on all 8 channels, 8 instruments integrated in one, hardware accelerated plotting, and fully upgradeable to 4 GHz.
-
Product
PXI Single 2 Channel (M Mode) ST 62.5 Cons
40-855-512-M62.5
Switch Module
Fiber Optic MEMS Switching cards available in many high density formats with a choice of five different connector styles to suit most applications
-
Product
CAN/FlexRay/Differential Bus PCI Fault Insertion Switch - 4 Channel
50-200-004
Fault Insertion Unit
This PCI Fault Insertion card is designed to simulate common faults on two wire communication interfaces such as CAN Bus. This card supports 4 or 8-channels of two wire serial interfaces. Each channel can simulate an open fault in either or both wires, a short between both wires or a short to one of eight externally applied fault connections, such as a battery connection or ground, via four fault buses.
-
Product
Infiniium UXR-Series Oscilloscope: 70 GHz, 2 Channels
UXR0702A
Oscilloscope
The UXR0702A is the 70 GHz, two-channel Infiniium UXR-Series real-time oscilloscope.
-
Product
Infiniium V-Series Oscilloscope: 16 GHz, 4 Analog Channels
DSAV164A
Oscilloscope
16 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.32 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
16, 32, or 48 Channel Isolated Digital Input Cards
PCI-IDI Series
-
PCI-IDI-xx Series cards offer a range of 16, 32, or 48 individual, optically isolated inputs. These cards are ideal for use in control and instrumentation applications where high-voltage protection is required. Individual channel-to-channel isolation allows every channel to be physically and electrically separated from the others.
-
Product
PXI Analog Output/Current Loop Simulator Module - 12 Channel
41-765-002
Analog Output Module
The 41/43-765-002 is a 12-channel Analog Output Module designed to meet the requirements of industrial control applications utilizing current loops 4 – 20mA. It consists of up to four 16-bit, digital-to-analogue converters (DAC), capable of creating four current outputs each. Output current within 0mA - 4mA and 20mA - 24mA, give the ability to simulate error or extra signaling conditions. The ±24mA mode gives the ability to simulate either sourcing or sinking sensor.
