LED
Semiconductor diode that emits narrow spectrum light by converting electric energy into electromagnetic radiation.
See Also: GaN
-
Product
Tone Generator
140BMC/6P
-
The following tests can be performed using the 140BMC/6P Tone Generator:*1000 Hertz or 500/1000 hertz alternating tone for tracing pairs.*Locates broken pairs/cables in walls. *Tone generator emits R.F. signal detectable by Aines Model 250SSP STATIONMAN Probe or 350 Filter Probe.*Provides talk power on dead pair.*Checks for shorts or opens, using a long-life lite-emitting diode (LED).*Continuity test.*Tip & Ring identifications.*Line condition identification. a. Clear line. b. Busy line. c. Ringing line.*Positive line verification.*Long battery life.*Nylon braided tinsel test lead wire for greater wear and flexibility.*Heavy duty nickel silver Aines 6P type alligator clips with custom designed vinyl boots.*Rubber grommet to prevent chafing on the test leads.
-
Product
50 Ohm Bridge / Freq Counter
-
* Generates a 3 to 30 MHz low level signal displayed on small 8 x 2 LCD * 50 ohm bridge supports tuning 50 ohm antennas * Adjust POT to find the resonate frequency of antenna * 30 turn POT allows easy smooth frequency adjustment * Bright red LED extinguishes when bridge is balanced * Function switching allows for use as frequency counter * 50 ohm termination included * measures 5.5 x 2.5 x 1.1 inches * 9 volt battery operation
-
Product
Light Source
pE-300white
-
CoolLED's pE-300white offers intense, broad-spectrum LED illumination for imaging most common fluorescent stains. The pE-300white Light Source can be fitted directly to the microscope or specified with a liquid light guide. The system is a mercury-free alternative that is safer, more controllable, and repeatable than conventional high-pressure gas discharge illuminators. Spectral coverage is from the UV (DAPI excitation) to the Red region (Cy5 excitation). The system is perfect for hospital and regular research laboratory environments.
-
Product
LED Pick & Place Machines
-
Shenzhen Leadsmt Technology Co.,Ltd
Is a kind of equipment used in the LED industry. It belongs to the SMT (Surface Mount System) placement machine, which can be used to assemble a large number of LED circuit boards.
-
Product
12-42V LED Heavy Duty Circuit Tester
1651A
-
Peaceful Thriving Enterprise Co Ltd
*Check on 12 - 42V systems. *Automatic voltage identification: BLUE LED for General car / RED LED for Hybrid car.
-
Product
Battery Gauges
-
Global Digital Instruments, LLC
Our battery fuel gauges and LED volt meters are designed to monitor the charge capacity of DC powered equipment and monitor information about the equipment's electrical system.
-
Product
Programmable LED DC Electronic Load
M98 Series
-
M98 series DC electronic load, as a new generation product of Maynuo Electronic Co., Ltd, is designed for the LED driver application. A special circuit is desiged for the LED driver on the base of the M97XX sereies. Incorporating high-performance chips, the M98XX series delivers high speed and high accuracy with a resolution of 0.1 mV and 0.01 mA (basic accuracy is 0.03% and basic current rise speed is 2.5 A/μs). M98XX series have wide application from production lines for cell phone chargers, cell phone batteries, electronic vehicle batteries, switching power supplies, linear power supplies, and LED drivers, to research institute, automotive electronic, aeronautic and astronautic, maritime, solar celland fuel cell etc.test and measurement applications.
-
Product
Digital CC and CV DC Power Supply
DC3005
-
The DC Series Power Supplies are with high stability and high accuracy. The voltage and current can be adjustable and can output costant current or constant voltage. They are suitable to supply DC Power for the standard lamp and the large power LED. Other voltage and current DC Power Supply can be designed according to customer’s request.
-
Product
AGC, SNMP, RFoG FTTB Optical receiver
RFoG4002, RFoG4004
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai RFoG4002 ( two-port ), RFoG4004 ( four-port ), is a type of high-grade AGC, Network management, RFoG FTTB outdoor optical receiver. Various operating parameters of machine are microprocessor-controlled, LED display. Through the keys of machine can adjust and set EQ、ATT. Optional network transponder, implement remote network management. Large dynamic range of optical AGC characteristics, RFoG4002 ( two-port ), RFoG4004 ( four-port ) high output ,for FTTC, FTTN fiber access network. As a unit of CATV network RX, is a high performance, highly flexible, cost-effective CATV optical receiver.
-
Product
Lasers And LEDs
-
AGILE features a broadband spectral output from <400 nm to >2000 nm and pulse repetition rates from 10 kHz to 1 MHz, making it the ideal light source for the majority of fluorescence lifetime applications. Using the Time-Correlated Single Photon Counting (TCSPC) technique, fluorescence lifetimes from a few picoseconds to microseconds can be accurately resolved. It is also compatible with Multi-Channel Scaling (MCS) mode for lifetimes up to 10 μs.
-
Product
Auto Charging System Analyzer
TE6-0606
-
Hangzhou Tonny Electric & Tools Co., Ltd.
This unit simply plugs into your car's cigarette lighter socket and will present you with alternator and battery status. On the left side is the alternator status indicating if it's charging the battery at too high a voltage, normal or too low. On the right is the battery status green LED charged 12.4-12.6V, yellow LED recharge 11.8-12.35V, and red LED dead<11.75V indicators.
-
Product
Current / Voltage input Panel meter with output options
DM3420
-
The DM3420 panel meter accepts Voltage and Current process signals and displays the process value on a high efficiency daylight readable LED display. A built in transmitter power supply is also provided.
-
Product
Economical LED Display for Remote Annunciator Applications
AN-3100D-LC
-
LED Illumination for long life, low power Laser Printed window Legends Compact Size Barrier, screw terminal connection Panel or 19" Rack Mounting 4 Windows Sizes: 3x3, 1.5x3, 1x3, 1.5x1.5 Selectable Window Colors: White, Red, Blue, Green Amber Built-in Test Pushbutton option
-
Product
GO-NR1000 Near-Field Goniophotometer
-
Hangzhou Everfine Photo-E-Info Co., LTD
Suitable for LED light source, LED chip, module and other small light source, the principal function includes: spatial light intensity distribution curve, spatial color distribution curve, iso-lux curve, total luminous flux, effective luminous flux, spatial luminance curve, etc.The test data can be saved as IESNA (*.ies), CIBSE (*.cib), EULUMDAT (*.ldt), CIE (*.cie), CEN (*.cen) and other formats, which can be directly used as the input data of international general lighting design software. Spatial luminance data can be imported into near-field lighting generation software to generate light data that can be imported into third parties (TracePro and LightTools).
-
Product
Bench-Top Type ASE Light Source
-
ASE(Amplified Spontaneous Emission) light sources are low-coherent light sources ,which combines the both features of high intensity like laser and broad spectrum like LED. Output stability is greater than those of LD and LED, and therefore they are suitable for high accuracy measurement applications. With the use of rare-earth-doped fluoride fibers, the plentiful lineup of FiberLabs light sources includes the 540 nm-, 850 nm-, 1300 nm-, 1480 nm- and SCL-bands that other companies do not provide.They are the best light sources for FBG sensors, OCT, fiber optic gyroscopes, gas sensors, and fluorescence excitation, as well as for measurement of optical components. The bench-top type is easy to use as a stand-alone light source and the modular type is convenient for integration into equipments.
-
Product
Power Supplies
CL-700B
-
Experience our new CL-series of power supplies. It has a 120mm Blue LED cooling fan for your gaming case & it has a 3 rail 12V output to fulfill all your system needs. 700W offer a 6+2 PCI-E ready for better graphics capabilities. Painted in black, the CL-series works great and looks great
-
Product
Breakout - General Purpose USB to GPIO+SPI+I2C
FT232H
-
This chip from FTDI is similar to their USB to serial converter chips but adds a ''multi-protocol synchronous serial engine'' which allows it to speak many common protocols like SPI, I2C, serial UART, JTAG, and more! There''s even a handful of digital GPIO pins that you can read and write to do things like flash LEDs, read switches or buttons, and more. The FT232H breakout is like adding a little swiss army knife for serial protocols to your computer!
-
Product
Tone & Probe Kits
-
Triplett Test Equipment & Tools
ProTone Wire Locator Kit features a powerful tone generator and a filtered, ultra-bright lighted probe. The CTX590 functions as a high quality wire locating tool that uses an inductive probe to sense a tone placed on the wires by its associated tone generator. The tone generator provides RJ11, RJ45 and insulated alligator clip connections. The Red/Green LED on the probe indicates continuity, voltage, and polarity. The probe also includes an ultra bright LED tip, fluorescent light noise filter and sensitivity control. The CTX590 can be used for tracking down short circuits, telephone central office connections, and other wire locating applications. Includes (2) 9V batteries and case.
-
Product
Programmable Setpoint Relay Protection Relay, Trip Relay
CRD-005 and CRD-020
-
CRD-020 Programmable ac current set-point relay setting for threshold levels, over and under-currentoperationbullet CRD-005 Programmable dc voltage and mA set-point relay setting for threshold levels, over and under-voltage operationbullet CRD-005 internal DIP-switches allow for either 0-1mAdc or 0-10Vdc operation, and may be set for under-alarm or over-alarm relay operationbullet CRD-020 internal DIP-switch allow configuration of the ac current range to either 0-5A, 0-10A, 0-15A or 0-20A and the relay mode for under-current or over-current operationbullet Lid mounted two digit numerical push button switch calibrated as percent of full scale with a threshold range of 1-99%bullet Red LED lamp lights to indicate when the threshold level has been tripped
-
Product
IVN-8561, Automotive Ethernet Interface Device
786169-01
Ethernet Interface
2-Channel, 4-Port, 100BASE-T1 to 100BASE-TX Automotive Ethernet Interface Device—The IVN-8561 is an interface that converts 100BASE-T1 unshielded twisted pair (UTP) automotive Ethernet to standard 100BASE-TX Ethernet. It is ideal for developing applications that require automotive Ethernet to test and validate automotive electronic control units (ECUs). The IVN-8561 provides two channels to convert data between 100BASE-TX Ethernet and 100BASE-T1 Automotive Ethernet. Each 100BASE-T1 port can be configured as master or slave, using switches on the front panel. The IVN-8561 also provides LED on the front panel so that you can monitor the linkage and activity on the various ports.
-
Product
Video Autoselector
1154A
-
Consumers who own a receiver and/or TV with limited inputs can use the 1154A to add multiple A/V sources. Its exclusive Adaptive Signal SensingTM technology uses multiple criteria to decide when to switch sources, and adapts to users’ activity patterns, customizing its switching behavior over time. The high bandwidth circuitry accepts HDTV component video (YPbPr), stereo analog audio, and digital audio in both optical and coaxial formats, and switches all audio and video signals simultaneously when a new source becomes active. Digital audio signals are converted automatically to the desired format. Up to four sources may be connected to one receiver/video display system through the 1154A. A manual select button is provided to override the 1154A’s automatic selection. Multi-color front panel LEDs indicate source availability.
-
Product
3 Digit LCD Meter
DPM 950S
-
The DPM 950S is a 3 digit LCD voltmeter with 19mm (0.75") digit height and LED backlighting. It features 200mV d.c. full scale reading, auto-zero and auto-polarity. The meter plugs directly into a 16-way IDC socket or can be panel mounted using the bezel. An optional IP67 / NEMA 4X bezel (BEZ 900-IP) is available for waterproof applications
-
Product
Frequency Monitors
FM Series
-
FM Series line-powered frequency monitors are high quality, dependable panel meters designed to continuously monitor line power frequency. Crystal reference-based for high accuracy, these 1/8 DIN/NEMA case style meters come with LED or LCD displays.
-
Product
Smoke Detector Tester
Solo 365
-
The fire industry’s most popular range of detector test equipment is about to get even better. Solo, the test equipment used world-wide to functionally test fire detectors has a new tester in its range – Solo 365. This exciting innovation provides fire safety professionals with an array of stand-out features which make for faster, simpler and cleaner functional testing of smoke detectors. Key features include automatic generation of smoke which ensures only the amount of smoke needed to activate the detector is produced – minimizing smoke wastage and eliminating the risk of detector contamination. In addition, Solo 365 is light in weight and has a slim-line design which allows easy access into tight spaces – making it possible to test detectors which are hard to access with other portable testers. In response to market feedback, Solo 365 features an LED torch which automatically illuminates when light levels drop, making for easy detector alignment and testing in dark environments. Smoke is generated via newly designed smoke cartridges which fit neatly into the rear of the tester. With no reliance on pressurised aerosol cans, the cartridges can be easily shipped and stored and are unaffected by new regulations, set for 2018, which will affect availability of some pressurised smoke aerosols.
-
Product
32-CH Discrete Input Modules
HSL-DI32-M-N/HSL-DI32-M-P
-
- Slave ID consumption: 2 consecutive from odd- "N" type for NPN sinking type sensor or dry contact; "P" type for PNP sourcing type sensor or wet contact- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ± 10 mA (Max), ± 12.5 mA (Peak)- Input voltage: ± 40 V (Max)- LED indicator: Power, Link and Input status- Power supply: +10 V to +30 VDC
-
Product
Logger version chlorophyll and turbidity sensor with wiper
INFINITY-CLW ACLW2-USB
-
Infinity-CLW is an autonomously deployable data logger for long-term chlorophyll and turbidity measurements. The light sources (LEDs) of chlorophyll and turbidity sensors are highly stable, Minimizing the change over time. The instrument has a mechanical wiper that periodically sweeps to inhibit biological growth on the optical window. The turbidity sensor has a good correlation with SS (Suspended Solid) over the range. Infinity-CLW provides Highly accurate and long-term stable chlorophyll and turbidity data in oceans, rivers and freshwater.
-
Product
Automotive Tester
7612A
-
This is the device to test 3 popular vehicle relays. The testing result will be displayed by LED indication. Technician is able to use the device to figure out the condition of the relay, and so speculating the problem in the vehicle. Use the relay adapter to plug into the relay tester, suitable to connection multiple styles relay.
-
Product
X-ray inspection system for BLU, LED Long bar products
X-eye 9000LED
-
X-ray Tube100kV / 200uAMin. Resolution5µmTable Size1,500mm X 500 mmDetectorFlat Panel Detector (High sensitivity)Dimension3,620(W) x 1,065(D) x 1,590(H)mm / 850kg
-
Product
Programmable DC Electronic Loads
SDL1000X/X-E Series
-
SDL1000X/SDL1000X-E series Programmable DC Electronic Load has a 3.5 inch TFT-LCD display, a user-friendly interface and superb performance specifications. The SDL1020X/SDL1020X-E models feature an input range of 150 V/30 A 200 W while the SDL1030X/SDL1030X-E have an input range of 150 V/30 A 300 W. The SDL1000X series leads with measurement resolution of 0.1 mV/0.1 mA and the base SDL1000X-E series resolution is 1 mV/1 mA and adjustable current rise times from 0.001 A/μs~2.5 A/μs. For remote communication and control, the SDL series includes RS232/USB/LAN interface types. The SDL1000X series delivers stability over a wide range of applications and can meet all kinds of testing requirements. including: Power, battery/handheld device design, industry, LED lighting, automotive electronics, and aerospace.
-
Product
S2 Penta High-Sensitivity Sensors
ULP S2 PCI/V HS
LED Sensor
The Universal LightProbe S2 Penta High Sensitivity Sensor features the same popular built-in color binning as the regular S2 Penta Sensor, and is designed test extremely dim LEDs, providing an analog output for intensity, ranging from 0 to 4 volts, corresponding to the LED’s luminous intensity in millicandelas. Implemented in a unique and customizable 2-Part solution, the S2 Penta High Sensitivity Sensor is assembled with your choice of Fiber-Optic Probe, including for the test of densely-spaced LEDs, bright LEDs, dim or misaligned LEDs, right-angle LEDs, and more, including the popular “Trident” Fiber-Optic Probes to sequentially test 3 LEDs with a single Sensor.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsOutput Pins: 4 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. longTypical response times: <1.2s color & intensity outputs simultaneously (the brighter the LED, the shorter theresponse time)Fiber-Optic Probes: Wide Aperture Fiber-Optic Probe recommended
