Microwave Amplifiers
boost signal power at low microwave frequencies acroos a broad spectrum.
See Also: RF Amplifiers, Rf Power Amplifiers, TWT Amplifiers
-
Product
40-67 GHz Power Amplifier
1GG6-8070
Amplifier
The 1GG6-8070 is a high gain, medium power mmwave amplifier. It can be used as part of a banded solution to achieve respectable mmwave power. Input and output ports are matched to 50W. The amplifier is biased with a single positive drain supply (VDD) and a single negative gate supply (VG1).
-
Product
Signal Amplifier
9400
Amplifier
Model 9400 was designed as a general purpose, wide band and high voltage amplifier however, with specific applications in mind. It has four channels built in a small case size to save space and cost but without compromising bandwidth and signal integrity.
-
Product
Synchro Power Amplifiers
SPA
Amplifier
Computer Conversions Corporation
The SPA Series "Pulsating" Synchro Power Amplifiers are proven, high efficiency, low cost, compact, reliable solid state synchro drivers; designed for demanding Naval/Maritime, Aircraft, fire control and radar/Antenna related, applications. They are commonly used on synchro based data transmission, re-transmission, simulation and instantaneous absolute position indicating and active control systems.
-
Product
Wideband Amplifier PXI Card
GX1222
Amplifier
The GX1222 is a 3U single-slot, PXI-based wideband power amplifier used for signal amplification purposes. Offering excellent fidelity, the GX1222 amplifies signals from DC to over 20 MHz with a fixed gain of x10. Custom gains are also available without compromising signal purity and amplifier performance.
-
Product
Signal Amplifier
9200
Amplifier
Model 9200 is a Single/Dual Channel, 2U, half-rack size, bench-top power amplifier designed for signal amplification. With unprecedented signal purity, Model 9200 amplifies signals from DC to over 500kHz. The unit has a fixed gain of x15 however the same amplifier is available with custom gain and no signal purity or performance degradation whatsoever.
-
Product
2-26.5 GHz GaAs MMIC Traveling Wave Amplifier
HMMC-5026
Amplifier
The HMMC-5026 is a broadband GaAs MMIC traveling wave amplifier designed for moderate gain and moderate output power over the full 2-26 GHz frequency range. Typical applications of the HMMC-5026 include wideband gain blocks of communication systems and microwave instrumentation, which require a flat gains response and excellent port matches over the 2-26 GHz frequency range.
-
Product
LXI Microwave Multiplexer, SP6T, 11-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-511
Microwave Multiplexer
Our 60-800-511 is a 11 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, SP6T, 8-Bank, 67GHz, 50Ω, SMA-1.85
60-800-808
Microwave Multiplexer
Our 60-800-808 is a 8 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
PXI Microwave Multiplexer, Dual SP4T, 26.5GHz, 50Ω, SMA, Terminated
40-785C-432-T
Microwave Multiplexer
The 40-785C-432-T (PXI) and 42-785C-432-T (PXIe) are dual SP4T 26.5GHz microwave multiplexers with automatic termination of unused signals. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
FieldFox Handheld Microwave Analyzer, 54 GHz
N9953B
Microwave Analyzer
A lightweight, durable, software-enabled cable and antenna analyzer, spectrum analyzer, network analyzer, and more.
-
Product
LXI Microwave Multiplexer, SP6T, 3-Bank, 67GHz, 50Ω, SMA-1.85
60-800-803
Microwave Multiplexer
Our 60-800-803 is a 3 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 67GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, SP6T, 9-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-509
Microwave Multiplexer
Our 60-800-509 is a 9 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Signal Amplifier
A10160
Amplifier
Model A10160 is an ultra-small footprint, wideband, DC coupled amplifier designed for high frequency, high current, signal amplification. With a high bandwidth of 45MHz, 34Vp-p into 50 ohms and up to 10W output power, the A10160 is the ideal complimentary amplifier to any signal source that needs a supporting power boost for demanding applications.
-
Product
FieldFox Handheld Microwave Analyzer, 14 GHz
N9916A
Microwave Analyzer
14 GHz max frequency Carry the world's most integrated handheld analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in the same sweep Simultaneously measure all four S-parameters Make accurate spectrum analyzer measurements ( 0.5 dB) without needing warm-up Calibrate simply with QuickCal
-
Product
FieldFox Handheld Microwave Analyzer, 44 GHz
N9951A
Microwave Analyzer
44 GHz max frequency Carry world's most integrated handheld W analyzer: standard model includes cable and antenna analyzer Expand capabilities with optional VNA, spectrum analyzer, built-in power meter, vector voltmeter, and more Save time by measuring DTF and TDR in a single sweep Simultaneously measure all four S-parameters Make accurate SA measurements ( 0.5 dB) without needing warm-up Easily measure average and pulse power with a USB sensor
-
Product
USB Preamplifier, 100 MHz to 26.5 GHz
U7227C
Amplifier
The U7227C, 100 MHz to 26.5 GHz USB preamplifier is designed to bring reliable gain and low noise figure to measurement systems improving the overall system performance and reduce systematic errors; a total solution to the X-Series signal analyzers to perform noise figure measurement
-
Product
Broadband Amplifier
BBL200
Amplifier
The R&S®BBL200 broadband amplifiers are ideal for applications requiring high RF power.
-
Product
LXI Microwave Multiplexer, SP6T, 12-Bank, 50GHz, 50Ω, SMA-2.4, Terminated
60-800-712
Microwave Multiplexer
High performance RF multiplexer suitable for switching microwave signals up to 50GHz with automatic termination of unused signals
-
Product
System Amplifiers
N4985A
Amplifier
The Keysight Technologies N4985A series system amplifiers are high performance broadband amplifiers with excellent power and gain from 100 kHz to 50 GHz. The amplifiers are self-contained and plug into standard AC power sources.
-
Product
Microwave System Amplifier, 45 MHz to 50 GHz
83051A
Amplifier
The Keysight 83051A microwave system amplifier is a compact, off-the-shelf amplifier designed for systems designers and integrators. This amplifier provides power where you need it to recover system losses and to boost available power in RF and microwave ATE systems. The ultrabroad bandwidth from 45 MHz to 50 GHz allows the designer to replace several narrow bandwidth amplifiers with a single Keysight amplifier, eliminating the need for crossover networks or multiple bias supplies.
-
Product
PXI Microwave Multiplexer, Dual SP4T, 26.5GHz, 50Ω, SMA
40-784B-132
Microwave Multiplexer
The 40-784B-132 (PXI) and 42-784B-132 (PXIe) are dual SP4T 26.5GHz unterminated microwave multiplexers. The 40/42-784B range is available with single, dual or triple, SP6T or SP4T multiplexers with front panel mounted or remotely mounted relays.
-
Product
PXI Microwave Multiplexer, Dual SP4T, 26.5GHz, 50Ω, SMA
40-785C-432
Microwave Multiplexer
The 40-785C-432 (PXI) and 42-785C-432 (PXIe) are dual SP4T 26.5GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
LXI Microwave Multiplexer, SP6T, 8-Bank, 40GHz, 50Ω, SMA-2.92, Terminated
60-800-508
Microwave Multiplexer
Our 60-800-508 is a 8 bank terminated SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 40GHz. The 60-800 range is capable of supporting up to 14 banks of 6 channel terminated multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, SP6T, 7-Bank, 50GHz, 50Ω, SMA-2.4, Terminated
60-800-707
Microwave Multiplexer
High performance RF multiplexer suitable for switching microwave signals up to 50GHz with automatic termination of unused signals
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 14-Bank 18GHz SMA
60-801-214
Microwave Multiplexer
The 60-801-214 is a 6-channel, 14-bank RF multiplexer suitable for switching 50Ω signals up to 18GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Laser Sources and Amplifiers
Amplifier
We design and manufacture a range of tunable C-band and L-band telecom laser sources, customizable fixed-wavelength laser sources, broadband super luminescent (SLED) sources, swept laser sources, and Erbium-Doped Fiber Amplifiers (EDFA).
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 16-Bank 26.5GHz SMA
60-801-316
Microwave Multiplexer
The 60-801-316 is a 6-channel, 16-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
LXI Microwave Multiplexer, SP6T, 16-Bank, 50GHz, 50Ω, SMA-2.4
60-800-616
Microwave Multiplexer
Our 60-800-616 is a 16 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, SP6T, 14-Bank, 50GHz, 50Ω, SMA-2.4
60-800-614
Microwave Multiplexer
Our 60-800-614 is a 14 bank SP6T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-800 range is capable of supporting up to 16 banks of 6 channel multiplexers and is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Microwave Switches
SMX-7XXX (Microwave)
Microwave Switch Module
The AMETEK VTI Instruments SMX-7000 Series of microwave switch cards extends functionality typically reserved for dedicated stand-alone systems into the PXIe from-factor. Single and dual slot configurations provide the ability to mix and match multiple switch configurations including SPDT, SP4T, SP6T and Transfer. Embedded virtual schematic control further simplifies setup and debugging allowing all relays to be engaged independent of application software and device drivers. Ideally suited for medium-to-high density automated test equipment (ATE), the SMX-7000 Series deliver uncompromised measurement integrity ideal for the most demanding aerospace, defense and communication applications.
