-
product
COM Express® Type 6 Reference Carrier Board in ATX Form Factor
Express-BASE6
The Express-BASE6 is an ATX size COM Express Type 6 reference carrier board. Together with the COM Express Type 6 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
Test Program Modules
The BRAT Test Program developed will provide functional validation of an assembly based on customer supplied documentation. This does not include hardware (e.g., Interface Test Adaptors), documentation (e.g., technical orders), travel or travel related per diem, or site verification test or installation.
-
product
ADSL / 2 / 2+ Handheld VoIP Tester
QuickTest 500
*Rapid Testing. The QuickTest 500 ADSL2+ Tester's automatic Service Verification Test Suite starts as soon as you switch on (results are typically obtained in less than 3 minutes)*Simple to use. Virtually no product training required with QuickTest 500 ADSL Tester*Configurable Pass / Fail Indicators on the LCD display and clearly presented in multi-colour LEDs on the front panel*No need to get a laptop out*Save and name up to 16 test results at any one time*Line Voltage LED indicates poor, missing or excessive Line Voltage*ADSL/2/2+ Test LEDs to indicate if ADSL Showtime achieved*In Service LED indicates problems with PPP or IP layer*LEDs to indicate problems with the Trained Line Rate, poor Noise Margin or excessive Line Attenuation
-
product
Proven Testing Solutions for Critical Software
V&V Services
*Unit and integration testing*System and acceptance testing*DO-178 process definition and optimization*Test automation*Timing analysis and optimization*On-target problem solving*Third-party software verification*Assurance services
-
product
Digital And Mixed Signal Oscilloscope
MSO/DPO70000 Series
The MSO/DPO70000 is one of the most advanced oscilloscopes in its class: enabling today’s engineer to see signals better with minimal noise, debug signal anomalies faster, reduce debug time, and utilize measurement and analysis tools for automated compliance testing and other verifications. In addition, the MSO/DPO70000 is perfect for analog/digital design and debug, data communications and high-speed serial communications. See how you can use the MSO/DPO70000 for your next project to find and analyze a wide range of mixed-signal anomalies.
-
product
PCI Resistor Card 4-Channel 1 Ohm To 510 Ohm
50-293-014
The 50-293 is a Programmable Resistor card with either two channels of 16-bit or four channels of 8-bit resistor chains in a single PCI card. The card is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Lead-acid Storage Battery Analyzer
From the beginning of 2006 the verification of measurements of the analyzer of lead-acid chemical sources developed by Company "Megaron" is spent in Test laboratory "Neva-Reglament". The analyzer is intended for the express-estimation of a condition of lead-acid batteries: before the first use of new battery (an estimation of the electric characteristics declared by the manufacturer); during the battery operation (an estimation of a condition and working capacity at real application).
-
product
PXI Resistor Module 2-Channel 2R to 32.7k with SPDT
40-293-132
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 2.04k Ohm
40-294-022
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
JTAG Boundary-Scan Controllers for High-Volume Production Systems
Corelis has designed special hardware that autonomously performs concurrent (gang) testing and programming of multiple units without additional user intervention. The entire testing and programming, including on-the-fly verification of results, is done in modular and expandable hardware.
-
product
FBI / MITRE Test Charts & Kits
FBI / MITRE Test Charts & Kits by Applied Image - FBI SIQT Scanner Test Chart, Individual Personal Identity Verification Test Charts for Single Fingerprint Capture Devices, Personal Identity Verification Kits for Single Fingerprint Devices
-
product
BSDL File Validation
Corelis offers services to validate the accuracy of Boundary-Scan Description Language (BSDL) files that characterize the boundary-scan functionality of semiconductor devices. These services include validation of a device's BSDL file while the chip is still in development and BSDL file accuracy verification against actual silicon.
-
product
Matrix Code Verification Systems
REA MLV-2D
The REA MLV-2D is a matrix- and barcode verifier which has been developed in conformance to international standards. The measurement uses defined angeles distance and illuminations to achieve repeatable results and quality information.
-
product
PCI High Density Potentiometer Card 4-Channel, 16-Bit, 0 To 65k Ohm
50-296A-121-4/16
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
DGN Advanced Reporting Feature, GTE 10.00p
K8223A
The Basic Diagnostics levels is the main troubleshooting tool used by all users to check the hardware configuration, and verify and isolate hardware failures. Some Diagnostic tests require that a Pin Verification Fixture be installed on the system.
-
product
PCI High Density Resistor Card 10-Channel, 16-Bit, 0 To 65k Ohm
50-295A-121-10/16
The 50-295A is a Programmable Resistor card with up to 18-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Parallel Simulation Engine
RocketSim
Complementing compiled-code simulators, Cadence® RocketSim™ parallel simulation engine eliminates functional verification bottlenecks by speeding up simulation using commonly available multi-core servers.
-
product
Multifunction I/O Device
The Multifunction I/O Device features I/O with varying channels, sample rates, output rates, and other features to meet many common measurement requirements. You can use the device for industry applications such as laboratory automation, research, and design verification. The included DAQExpress companion software provides basic measurement and analysis, while the included NI-DAQmx driver provides the ability to create customized automated measurement and control applications. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
RF Detectors
BroadWave designs and manufactures RF Detectors and other coaxial RF components that are ideally suited for test, verification and system integration. With frequency ranges of DC to 18 GHz, our components offer consistent performance at a low cost with an emphasis on performance and configuration flexibility.
-
product
DGN Advanced Reporting Feature, GTE 10.00p
K8223B
The Basic Diagnostics levels is the main troubleshooting tool used by all users to check the hardware configuration, and verify and isolate hardware failures. Some Diagnostic tests require that a Pin Verification Fixture be installed on the system.
-
product
Multi-Functional Dynamic System Monitor
PFMonitor
The PowerFactory Monitor (PFM) is multi-functional Dynamic System Monitor which fully integrates with DIgSILENT PowerFactory software. The PFM features grid and plant monitoring, fault recording, grid characteristics analysis by offering easy access to recorded data, analysis of trends, verification of system upset responses and test results.
-
product
Inspection Microscope
Z-NIR
The McBain Z-NIR Near Infrared Inspection System is best-in-class for wafer-to-wafer and die-to-die alignment measurement and verification. This unique tool has been sold into many industries with various applications including sub-surface wafer and die inspection for cracks and bond integrity, MEMS, wafer bonding, 3-D chip stacking, failure analysis, process development, tool verification, part characterization, environmental testing and more.
-
product
PXI Programmable Resistor Card 2-Channel 2.5 Ohm to 8.19k Ohm
40-294-024
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm
40-294-011
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
Three-Phase Meter Test Equipment
ASTEL 3.2 TYPE
ASTeL 3.2 meter test equipment is a fully automatic system that enables simultaneous, multi-position calibration and verification of three-phase electric energy meters. ASTeL 3.2 offers full compatibility with IEC 60736. Thanks to excellent parameters, superior functionality and outstanding flexibility, ASTeL 3.2 is an ideal solution for utility companies, energy meter manufacturers, governmental institutes of metrology, metrological laboratories, and other customers interested in electricity meters testing.
-
product
Moisture Analyzer Series
3050
The 3050 series of moisture analyzers utilizes AMETEK’s proven, accurate quartz crystal microbalance (QCM) technology. Built-in verification provides operators with increased measurement confidence.
-
product
Wideband Active Load Pull Export Control
S94573B
The software enables power amplifier distortion measurements under varying load conditions that are controlled across the entire modulation bandwidth. When design verification and robustness evaluation require testing the device away from the optimum loading condition, this application provides powerful insight into device performance and degradation.
-
product
PXI RTD Simulator Module 6-Channel PT100
40-262-101
The 40-262 is a 3U PXI module range that supports 6 (in one slot), 12 or 18 (in two slots) channels of RTD simulation. Based on the 40-260 design principles the module can provide a setting resolution of <8mΩ (PT100) or <90mΩ (PT1000) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
product
Systems
Datum Electronics Systems - Silo Hawk silo weighing system, Datum Hawk engine condition monitoring system, Cargo Hawk SOLAS compliant container weight verification system, and more
-
product
Rapita Verification Suite
RVS
*Run requirements-based tests on your code *Produce coverage evidence including MC/DC from tests *Analyze execution time including worst-case timing on-target *Understand program scheduling behavior *Produce evidence for DO-178 and ISO 26262 certification
