Showing results: 1 - 15 of 15 items found.
-
XJFlash -
XJTAG Ltd.
XJFlash is an FPGA-based advanced and innovative method that uses JTAG for high-speed in-system programming (ISP) of flash memories – all serial and parallel flash devices are supported. The most common use of XJFlash is programming the SPI/QSPI NOR flash used to configure an FPGA.
-
XJDeveloper -
XJTAG Ltd.
XJDeveloper is a graphical application that allows you to quickly and easily set up and run tests on your circuit. With XJDeveloper you can reduce your time to market by reusing your test scripts all the way through the product design process and then in manufacturing.
-
XJInvestigator -
XJTAG Ltd.
Much more than a production line test tool, XJInvestigator is a repair focused, integrated test and debug environment for fault analysis, helping you efficiently recover your failing boards.
-
XJDirect -
XJTAG Ltd.
XJDirect is an advanced and innovative method for programming the internal flash of your processor and implementing some aspects of board test through JTAG when traditional boundary scan techniques cannot be used.
-
XJRunner -
XJTAG Ltd.
XJRunner is the specialised run-time environment for executing pre-compiled XJDeveloper projects. With a range of special features it is particularly aimed at board manufacturers and in-field support.
-
XJTAG Ltd.
The small, lightweight design means the XJLink2 can easily be moved to the Unit Under Test (UUT). Advanced features, like their programmable JTAG signal pin position, switchable power supply and auto signal skew, make it easy to connect to a wide range of circuit boards. Simple to install and use due to the USB plug-and-play ability.
-
XJTAG Ltd.
The XJLink2-3030 provides convenient, integrated access to XJTAG’s powerful boundary scan test and programming tools from SPEA 3030 ICT machines.
-
XJTAG Ltd.
The XJLink2-3070, approved by Keysight Technologies, provides convenient, integrated access to XJTAG’s powerful boundary scan test and programming tools from Keysight (Agilent) i3070 ICT machines.
-
XJAPI -
XJTAG Ltd.
The XJAPI is a simple-to-use DLL Application Program Interface (API), designed to give you low-level access to the JTAG chain via either the XJLink or the PXI hardware, allowing easy integration with a wide range of other systems such as development/evaluation boards, test systems
-
XJTAG Ltd.
XJTAG offers consultancy services to design and build production test fixtures that integrate JTAG boundary scan with bed-of-nails testing.
-
PXI XJLink2 -
XJTAG Ltd.
The PXI XJLink2 module allows the integration of XJTAG into PXI-based test systems. PXI XJLink2 has one JTAG controller that can be connected to up to 4 JTAG chains, which are configurable for pinout and voltage. It is easily integrated with LabVIEWTM with a full set of Virtual Instruments (VIs) included.
-
XJTAG Ltd.
The XJLink2-CFM is an advanced multi-TAP JTAG controller that fits into one of four Custom Function Module (CFM) locations on a Teradyne Multi-Function Application Board. It offers convenient, integrated access to XJTAG’s powerful test and programming tools from Teradyne’s TestStation™ In-Circuit Test Systems.
-
XJIO -
XJTAG Ltd.
The XJIO boards are expansion units that enable you to improve the test coverage for a Unit Under Test (UUT) by verifying the signals right through to the external connections. They will integrate with your XJTAG test system to provide access to otherwise inaccessible areas of your circuit. With a range of digital and analogue I/O pins on the board, you can improve fault isolation, verify power rail levels, and dispense with costly custom test jigs - even for non-JTAG boards.
-
XJAnalyser -
XJTAG Ltd.
XJAnalyser is a powerful tool for circuit visualisation and debugging. It provides a graphical view of JTAG chains, giving you complete control, on a pin-by-pin basis, of both pin state (either driven as an output or tristated as an input) and pin value (either high or low when driven), and it has the facility to run SVF and STAPL / JAM files.
-
XJQuad -
XJTAG Ltd.
XJQuad is a 4-port version of the XJLink2 USB-to-JTAG controller targeted at PCB manufacturers. It is supplied with XJRunner software for running XJDeveloper test systems. With a range of special features it is particularly suitable for concurrent/parallel testing on the production line. Each of the four ports has a high-speed interface which can be connected to up to four JTAG chains on each Unit Under Test (UUT).
