Showing results: 46 - 58 of 58 items found.
-
ABex TM-1149Cx-FXT -
Konrad Technologies GmbH
The ABex TM-1149Cx-FXT is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C4-FXT-X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan card it’s possible to connect up to four JTAG/Boundary Scan TAPs. All differential signal wires on the PCB are impedance controlled. In addition, all other digital signals (PIP, TRG, Aux, I/O) and Ground can be switched off via relays.
-
ABex TM-1149Cx -
Konrad Technologies GmbH
The ABex TM-1149Cx is an ABex terminal module for the Göpel Boundary Scan Controller SFX/PXI(e) 1149/C2/X or SFX/PXI(e) 1149/C4/X. It is connected to the BSCAN-Controller with an adapter-paddle-card.In combination with the above Göpel Boundary scan cards it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
ABex AM-306 Relay -
Konrad Technologies GmbH
The ABex AM-306 is a performance relay card for signal interconnection up to 110V / 2A. The relay board has 100 channels divided into 88 single channels and 3 blocks witch 4 channels each which are switched to a common root (multiplexer).The ABex AM-306 is designed as a pin compatible replacement for the ABex AM-302 as well as the ABex AM-303.
-
ABex RM-DIGIO -
Konrad Technologies GmbH
The ABex RM-DIGIO is a rear module for the ABex System. It is designed to connect digital signals to the back of a ABex chassis for example for cabinet control. As all IOs are isolated it’s possible to use different voltage levels for each IO.
-
ABex AM-300 Controller -
Konrad Technologies GmbH
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
ABex TM-6570 DPI -
Konrad Technologies GmbH
The ABex TM-6570 is an ABex terminal module to interface with NI PXIe 6570 / 6571 cards.In combination with the NI PXIe 6570/6571 it features a 32 channel Digital Pattern Instrument (DPI) and a 32×4 matrix, which could also be configured as a dual 16×4 matrix.As a DPI in combination with the NI PXIe 657x it offers 32 channels with up to 100Mhz, which can be individually connected and disconnected from the ABex front connector or routed to the ABex analog bus.
-
KT RFCT 2400 -
Konrad Technologies GmbH
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
ABex TM-JT37x7 -
Konrad Technologies GmbH
The ABex TM-JT37x7 is an ABex terminal module for the JTAG Technologies Boundary Scan Controller PXI/PXIe JT 37×7. In combination with the JT 2147/ABex from JTAG Technologies it integrates the POD functionality into the module.In combination with the PXI/PXIe JT 37×7 and the JT 2147/ABex it’s possible to connect up to four JTAG/Boundary Scan TAPs. All signal wires on the PCB are impedance controlled. In addition, all signals can be switched off via relays.
-
ABex TM-4070 DMM -
Konrad Technologies GmbH
The ABex TM-4070 is an ABex terminal module to interface with NI PXI-407x or PXIe-408x and gives the possibility to rout the DMM signals to the front connector and the Analog bus. The routing to the analog bus is software controlled and the signals are switched with reed relays.
-
ABex TM-4132 SMU -
Konrad Technologies GmbH
The ABex SMU-4132 is an Abex terminal module to interface with the NI PXI-4132. It is capable of routing signals of the PXI-4132 to the front connector. All signals are equipped with cut-off relays.
-
LEON Bench -
Konrad Technologies GmbH
The LEONBench test system is a flexible and scalable test system that features an excellent signal integrity and a high-quality fixture interface. This is achieved by combining a cableless connection from ABex modules to Virginia panel interface connectors. The system is optimized for high pin count test applications. Furthermore, it can be equipped with vacuum and pneumatic. Support for multi-level contact fixtures enables separate contact levels for FCT and ICT. The Konrad ITA (Interchangeable Test Adapter) frame allows various fixture houses all over the world to build custom fixtures for the LEONBench. Up to 15U additional rack space allows adding a bunch of high-performance measurement devices from various manufactures. An integrated power distribution unit takes care about power on and off sequencing.As part of the LEON Family, LEONBench is based on the ABex platform which directly incorporates Konrad analog bus technology and PXI/PXIe in one chassis.
-
ABex REC21-84TE-EXT -
Konrad Technologies GmbH
Robust and flexible interconnect solution for test fixtures. Designed for the use with ABex PXIe Rack 18 it provides support to equip all 21 slots with VPC interconnect modules. In addition, it offers 6 more slots on the bottom, below the ABex rack to feed through signals from external measurement devices.The interface uses the well-known Virginia Panel connectors with more than 20.000 guaranteed mating cycles. To build DUT specific test fixture, we also provide the corresponding ITA mounting frame (ITA = Interchangable Test Adapter).
-
ABex AM-307 FR-NXG Flashrunner -
Konrad Technologies GmbH
The ABex AM-FR-NXG incorporates the FlashRunner LAN 2.0 Next Generation from SMH Technologies. The FlashRunner is used to program microcontrollers, flash and other logic and memory devices. All DIO’s, the programmable voltage lines and the corresponding ground lines can be switched by relays.The ABex AM-FR-NXG is equipped with an onboard Ethernet Controller which connects the FlashRunner directly to the PXIe Backplane of the ABex Chassis. Using a windows host, each AM-FR-NXG will provide its own network adapter.