Showing recent results 1 - 15 of 66 products found.
-
Series 93(x) - Milimeter Wave Products, Inc.
Mi-Waves’ 93x Series Active Frequency Multipliers are capable of extending microwave frequencies from 5 to 30Ghz up to 170GHz in narrow band or full band applications. The use of MIC and MMIC’s allow greater bandwidths and power outputs. These multipliers are used for LO sources, frequency extenders, and test lab equipment. Please contact MI-WAVE for exact requirements.
-
990/991 Series - Milimeter Wave Products, Inc.
Mi-Waves’ 990 series balanced phase detectors feature a pair of Schottky diodes that that mix or beat two input signals at the same frequency to produce a DC output voltage proportional to the phase difference of the input signals.
-
202 & 203 Series - Milimeter Wave Products, Inc.
Antenna consist of a parabolic reflector, a linearly-polarized primary feed, anda feed support assembly, that isattached to the rim of the reflector inorder to position the feed reflector in order to position the feed accurately.Tapped holes are provided on eachantenna for mounting.
-
523 Series - Milimeter Wave Products, Inc.
Mi-Wave’s 523 Series MicrometerdrivenCalibrated Attenuators arecompact precision attenuating devices available in standard waveguide sizes from 18.0 to 220 GHz.
-
527 Series - Milimeter Wave Products, Inc.
Mi-Wave’s 527 Series Phase Shifters are designed for operation in waveguide sizes from 18 to 220 GHz. This resolution is advantageous since the total travel of the phase shift vane is quite short at high frequencies
-
551 Series - Milimeter Wave Products, Inc.
Each of Mi-Wave’s 551 Series Direct-reading FrequencyMeters are available in standard waveguide sizes from 18.0 to 170.0 GHz and are designed to provide easy direct readout of frequencywith a high degree of resolution and accuracy
-
528 Series - Milimeter Wave Products, Inc.
Mi-Waves' 528 series direct reading phase shifters provide highly accurate measurement of phase shift over each full waveguide band from 26.5 to 110.0 GHz. They feature low VSWR, low insertion loss, and low insertion loss variation due to the rotation of the phasing section.
-
510 Series - Milimeter Wave Products, Inc.
Mi-Waves' 510 series direct-reading precision attenuators provide 0 to 60 dB of calibrated attenuation by rotation of a resistive vane mounted in a circular waveguide section. These units are often referred to as "precision rotary vane attenuators". Calibration Accuracy is 0.1 db or 2% of reading whichever is greater to 40 db, 3 % from 40 to 50 db and 50 db and above is for reference level only not calibrated.
-
512 Series - Milimeter Wave Products, Inc.
The attenuators' small compact size incorporates both the electronic controller and microwave components. The unit operates from a single +24 volt DC source or with an optionalAC adapter.
-
283 Series - Milimeter Wave Products, Inc.
Mi-Wave’s 283 Series Polarizer, similar to the 282 Series, will convert linearinput signals to circular output signals with selectable output features. A manualswitch on the unit allows for selection of the output signal's polarization senseor conversion back to a linear polarization. Therefore, for any linearly polarizedinput signal, the output may be selected to be right circular, left circular or linearpolarization. The characteristics of the circularly polarized signal are similar to the282 models
-
410 Family - Milimeter Wave Products, Inc.
Mi-Wave’s 410 Series Waveguide to Coax Transitions allow an efficient method of adapting from rectangular waveguide to a coaxial connector.Full waveguide bands available from 12.4 to 110 GHz.
-
955 Family - Milimeter Wave Products, Inc.
Mi-Wave's 955 Series microwave and millimeter wave amplifiers offer a wide variety of frequency ranges, bandwidths, gain and power outputs.
-
Milimeter Wave Products, Inc.
Millimeter Wave Products Inc has developed a line of millimeter waveguide calibration kits for calibrating Vector Network Analyzers (VNA) utilizing millimeter waveguide test heads or modules from 26.5 to 260 GHz. These kits provide the Short-Short-Load-Thru (SSLT) calibration method utilizing offset shorts and a fixed precision termination.
-
Milimeter Wave Products, Inc.
At MI-Wave we can provide you with custom designed, tested and manufactured systems. From custom waveguides, assemblies, sub-assemblies to full fledged system builds. Contact us to inquire about working with Mi-Wave to bring your custom created systems to life.
-
Milimeter Wave Products, Inc.
Mi-Waves can help you create custom designed antennas for any application. Our team of engineers will work with you on developing and testing your antenna design and manufacturing needs. Our state of the art anechoic chamber is used for all our antenna tests during the manufacturing process.Please consult Mi-Wave for more details.
