Alacron

Offers a comprehensive line of products based on Microprocessors and FPGA's There are programmable FPGA data acquisition units that also perform pre-processing or low level processing. This includes processor and multiprocessor accelerated framegrabbers , framegrabbers, I/O boards, daughter cards, system software including comprehensive application libraries, and complete integrated application development platforms.

  • (603) 891-2750
  • (603) 891-2745
  • support@alacron.com
  • sales@alacron.com
  • 71 Spit Brook Rd.
    Suite 204
    Nashua, NH 03060
    United States

Filter Results By:

Products

Applications

Showing results: 1 - 12 of 12 items found.

  • Framegrabber

    FastX-UXGA - Alacron

    The FastX-UXGA frame grabber series is for users who anticipate a demand for extreme I/O requirements or higher bandwidth, complex image processing and real-time fast storage in a cost effective platform. The base Fast-UXGA, is a raw-length PCI board with two (four-muxed) UXGA analog conversion channels using Analog Device's AD9888. The front end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, from zero to four PNX1702 processors before output. Finally, the Fast-UXGA interfaces to the host computer through a 4x PCIe interface for state-of-the-art data acquisition.

  • Framegrabber

    FastXe2 - Alacron

    The FastXe2 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastXe, is a one half length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex 7 FPGA before being sent to the PCIe (X4) Gen 2 bus

  • Framegrabber

    FastX-APU - Alacron

    The FastX-APU framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX-APU, is a two thirds length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as GigEx4, high speed analog formats such as UXGA or DVI, or CoaXPress. The front-end data is formatted and preprocessed by a Kintex FPGA before being sent to the PCIe (X4) Gen 2 switch to the host or the AMD APU.

  • Framegrabber

    FastX1703 - Alacron

    The FastX1703 framegrabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX1703, is a two thirds length raw form factor PCI board six basic 85 MHz Camera Link Channels or an extended Camera Link camera interface. An auxilliary I/O connector provides a header for adaptation of other high speed interfaces such as LVDS or high speed analog formats such as UXGA or DVI. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, up to four PNX1702 500 MHz processors with 256MB memory each. Finally, the FastX1703 interfaces to the host computer through a 4xPCIe interface for state-of-the-art data acquisition.

  • Framegrabber

    FastX3 - Alacron

    The FastX3 frame grabber series is for users who anticipate a demand for extreme I/O requirements and/or higher bandwidth, complex image processing and real-time high-speed storage in a cost effective platform. The base FastX3, is a one half-length raw form factor PCIe (X4) Gen2 board with either six basic 85 MHz Camera Link Channels up to two extended full Camera Link camera interfaces. The front-end data is formatted and preprocessed by an Artix FPGA beforie being sent to the PCIe (X4) Gen 2 interface. It also is POCL and has isolated inputs including three LVDS I/Os.

  • PCI Board

    FastX1703-DIG - Alacron

    The FastX1703-DIG is a raw-length PCI board with two input connectors. Each connector supports 16 data bits, 10 general purpose inputs, and 6 general purpose outputs. Clock rates up to 166 MHz can be supported. All the inputs and outputs are connected to an FPGA on the board are essentially available for any purpose required by the interface. The front-end data is formatted and preprocessed by a FPGA before being sent to the memory subsection, zero to four Nexperia PNX1702 VLIW processors before output. Finally, the Fast-X-DIG interfaces to the host computer through a 4 x PCIe interface for state-of-the-art data acquisition.

  • Superlattice Doping / ALD Services

    Alacron

    Alacron, Inc. is capable of processing sensor wafers on a contract basis to produce backside illuminated wafers sensitive in the UV and soft X-Ray region with an array of anti-reflective coatings based on licensed patented, (US 8,395,243 and US 8,680,637), technology from Jet Propulsion Laboratory (JPL).

  • Backside Illumination (BSI) Services

    Alacron

    Your product description goes here.

  • FastCamera

    FC300 - Alacron

    The FastCamera 300 is a high-speed 3 megapixel digital camera system, using a CMOS imager with an electronic global shutter. This camera has a the option of a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include back thinned versions with high QE in the visible and NIR range, ruggedized, Camera Link output. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.

  • Frame Grabber Software

    Alacron

    Alacron provides the complete software environment needed to get your machine vision or imaging application up and running quickly — from concept to working high performance systems. O/S environments supported include Windows 2000, WIN XP, Solaris, and Linux. Alacron's CODE DEVELOPMENT TOOLS provides all the facilities needed to develop and debug code for simple framegrabbers to multiprocessor applications.

  • FastCamera

    FC200 - Alacron

    The FastCamera 200 is a high-speed 2 megapixel digital camera system, using a CMOS imager with an electronic global shutter. This camera has a the option of a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include back thinned versions with high QE in the visible and NIR range, ruggedized, Camera Link output. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.

  • FastCamera

    FC1700 - Alacron

    The FastCamera FC1700 is a high-speed 17 megapixel digital camera system, using a CMOS imager with an electronic global shutter, or rolling shutter. This camera has a high-speed, scalable, integrated FPGA, image processor, and memory subsystem which enables stand-alone high speed in camera image processing and extended storage. Options include ruggedized, Expanded Camera Link output, Gigabit Ethernet output, and in camera recording. When integrated with a high powered frame grabber /coprocessor board, the resulting system capabilities can be expanded by adding processors and memory on the board according to the needs of the user.

Get Help