Showing results: 1 - 15 of 28 items found.
-
M6 -
Seismic Source Co.
*Built-in damping and overrange stops*Safe overrange limits*Force up to 2000 G without damage to sensor*Temperature compensated for accurate response over entire temperature range*High slew rate operational amplifiers (1.2 V/usec)*Internal RF shielding on each pin
-
M7 -
Seismic Source Co.
*Dual independent Accelerometers for Quality Assurance*Protected against electromagnetic interference (EMI)*Protected against moisture*Input polarity protected*Output short circuit protected*Withstands up to 2000 g's without damage
-
BOOM BOX III -
Seismic Source Co.
*Easy to Use, just hold the Arm and Charge toggles, Unit charges and is ready to fire*Web based interface allows easy setup and storage of data on PC, Tablet, or Cell phone*Shooter updated with easy to read graphical display and status LEDs*Same unit used for Encoder and Decoder modes
-
Seismic Source Co.
Load Cell is designed by Seismic Source Company to measure the Hold Down weight and the output force of the Servo Hydraulic Vibrator unit. The output of the Load Cells can be recorded with any accurate seismic recording system.
-
Bird Dog 3 - 11 Channel -
Seismic Source Co.
*Additional Functionality when compared with Standard Bird Dog 3-3*32-bit, high speed, ADC chips for lower noise and increased accuracy*8 Gigabytes of Data Storage, Expandable to 16*GPS based time and location saved for every record*Stable and rugged unit for use in all conditions*Eleven-Channels, unit checks multiple vibrators at once to save time and effort*All test data saved in non-volatile memory for later download and retrieval*Connects to PC via Ethernet or optional Wi-Fi, provides control, data download and real time display and analysis of data and results
-
RTM3 -
Seismic Source Co.
The Remote Trigger Module 3, or RTM3 3, is a new generation of impact trigger device. It is designed to time synchronize a single seismic source unit with multiple seismic recorders. It can also be used to synchronize multiple seismic recorders. The RTM3 units use an internal high accuracy oscillator that is synchronized to GPS timing information. Each RTM3 unit requires an external GPS receiver with valid satellite information to synchronize the internal clock. Once the internal clock is synchronized the RTM3 can be used without any GPS signal for up to 10 minutes.
-
-
-
DAQlink 4 -
Seismic Source Co.
DAQlink4 is the fourth generation of portable seismograph systems. It can be configured as a stand-alone monitoring system, a refraction system or a distributed seismic reflection system.
-
DX6 -
Seismic Source Co.
The DX6 is a 6 channel seismograph that can be used for almost any seismic project. With its internal memory, optional USB memory and GPS, the flexible DX6 node can be deployed anywhere, at any time.
-
Vscope -
Seismic Source Co.
The Vscope Software program is used to operate single or multiple DAQlink Units. The Software provides full support to setup unit for autonomous or real-time operation.
-
GPS Tracker -
Seismic Source Co.
*Real Time display and History of all Vehicles and Personnel on Crew*Safety Reports and Legal documentation*Built around Google Earth – Data Reports free to everyone
-
SourceLink -
Seismic Source Co.
Specifically designed to maximize production with Continuous Recording Systems like iSeis Sigma, OYO GSR, Fairfield Node, Sercel Unite and all other systems.
-
Bird Dog 3 -
Seismic Source Co.
*32-bit, high speed, ADC chip for lower noise and increased accuracy*Multiple modes with a single unit*Connects to PC via Ethernet or optional Wi-Fi, to provide control, data download and real time displayand analysis of data and results*Test three geophone elements/strings or one three-component geophone*Test one hydrophone, both acoustic and electrical performance*Run wireline tests or performance tests on a single vibrator*8 Gigabytes of Data Storage, Expandable to 16*All test data saved in non-volatile memory for later download and retrieval*GPS based time and location saved for every test*Stable and rugged unit for use in all situations and conditions
-
Accelerometer Test Unit -
Seismic Source Co.
*Quick and Accurate Accelerometer Test*Battery operation*All tests use 32-bit resolution A to D Converter*All data downloaded to PC via Ethernet link*Records all data to a flexible easy to use database*Records time and date of tests