Showing results: 166 - 180 of 181 items found.
-
ZET 7070 -
ZETLAB Company
Basic delivery scope with digital transducers for laboratory use includes the following: interface converter ZET 7070, power supply module 220V→ +24V, measuring line connector ZET 7001 (these components are mounted on a din-rail 300 mm); cable USB 2.0 A→B – length 1,8 m; terminal resistance 120 Ohm (for industrial use — steel plug); CD with ZETLAB SENSOR software, enabling connection of up to 60 digital sensors; set of operational documentation.
-
ZET 7176 -
ZETLAB Company
Interface converter Ethernet/Wi-Fi↔CAN ZET 7176 is used for connection of CAN interface instrument communications nets based on digital transducers to PC over Wi-Fi or Ethernet. Wi-Fi or Ethernet network throughput rate allows to immediately fulfill commands and transmit great scope of data. Shared use of ZET7176 and ZET 7172 interface converters allows arranging instrument communications nets with radio linked transmission interface.
-
ZETLAB Company
Electrical networks control system is intended for measurements of network electrical resistance and insulation electrical resistance of the tested specimen. The measurement process takes a couple of minutes.
-
ZET 7012-A-VER.3 -
ZETLAB Company
Digital pressure meter ZET 7012-A-VER.3 is used for fast and simple absolute pressure measurements and measured values data transfer in digital format via RS-485 or 4-20 mA interface.
-
GT301 -
ZETLAB Company
Acoustic emission transducer GT301 converts acoustic signal into electrical signal, parameters of which are used for acoustic emission source evaluation.
-
ZETLAB Company
The digital sensors are used for the purpose of tests automation. The sensors measure the applied force value and the changes in linear dimensions of the specimen.
-
ZET 7177 -
ZETLAB Company
ZET 7177 CAN→GSM interface converter can be used under conditions when there is no access to a regular connection over Ethernet, or when you need to provide a redundant channel in case of Ethernet fouling.
-
ZET 7060-S -
ZETLAB Company
ZET 7060-S – stepper motor digital control module with RS-485 interface.
-
ZETLAB Company
Calibration of the seismic sensors should be conducted in the low-frequency domain, which means, that the relative method used for calibration of the vibration transducers is not applicable since it does not guarantee the required accuracy level. The problem is that the reference accelerometers have uneven AFR characteristic in the low-frequency domain. Thus, calibration of seismic transducers requires implementation of a different approach.
-
ZET 017-U Series -
ZETLAB Company
Shaker Controllers of ZET 017-U series are represented by a software and hardware complex solutions based on FFT spectrum analyzer ZET 017 with task-specific software ZETLAB VIBRO for the control of shock and vibration impact produced by electrodynamic shaker systems. The modular principle of the system structure allows to increase the number of measuring channels from 4 up to 24.
-
ZETLAB Company
Leak detection system (LDS) is a state-of-the-art software and hardware suite intended for leak detection in long-distance and oil products pipelines, calculation of leak location and evaluation of its intensity in constant full-time mode. The system allows to detect leaks in stationary and non-stationary pumping modes without gravity mains as well as in suspended pumping mode.
-
SHM -
ZETLAB Company
Automated stationary structural health monitoring system (SHM) is a subsystem of buildings and structures control system which has been developed in accordance with the applicable requirements of the corresponding standards. It is used to detect a transition of the building state from operational into the state of failure, that may eventually lead to fatal accidents.
-
ZETLAB Company
Torque measurement system is intended for periodical control and endurance testing of various moving structural elements, e.g. turbine blades, etc.
-
ZETLAB Company
The kit for seismic research performance is used for performing measurements in various climatic zones. Splash-proof connections GSC-4H (Herma-4) are used for establishing a reliable connection between the geophones within the seismic system.
-
ZETLAB Company
For the purpose of oscillations period determination, there is used an indirect measuring method, which registers oscillation processes in three mutually transverse axes. As a result of measurements, one can obtain oscillations period values and corresponding decrement values for each of the axes.