kV

NSG 438 ESD simulator comprehensively fulfills virtually all international standard requirements and supports proposed future standards. Air and contact discharge 200V to 30kV. Touch panel display controlled. Battery powered. Compliant with all known standards (IEC, ANSI, SAE, ISO, MIL etc). Interchangeable network modules. Discharge detector. ...more

Kit includes 4 Scope/DMM leads, ground lead, kV ignition lead, ignition sync lead, HEI adapter, manual, InfoTech Smart Card, CD, and carrying case. ...more

Full Function DMM. kV Tester. Sensor Tester. Fuel Injection Tester. Pressure Tester. Battery Drain Tester. Ground Tester. Noid Lights. Charging System Teste. All features are included: Volts, Ohms, Amps, BATT, ELEC, SEN, FUEL, and IGN. The kit includes the ignition DAT leads as shown.  ...more

Measures up to 9,900 volts (9.9 kv). Provides accurate readings on poly tape, poly wire, and steel wire. ...more

Functions include Power, Current, Insulation Resistance, and Temperature (Type K). True Power (kW) measurements, Apparent Power (kVA), and Phase Angle with Lead/Lag indicator. AC+DC µA Current with 10nA resolution for flame rod tests. Max/Min with elapsed time. Auto Detect AC/DC Voltage measurements with simultaneous Frequency display  ...more

Four clamps for power measurements on single phase, 3-phase/3-wire or 3-phase/4-wire systems. Large backlighting LCD displays 10 parameters simultaneously (kW, kVAR, kVA, PF plus the voltage and current of the three phases)  ...more

There's no faster way to measure and compare peak kV, or verify the proper firing of the secondary ingnition system, than with the kV/Arc Quick Probe. The kV/Arc Quick Probe is easy to use ? simply place the probe over the ignition wire. Each time the unit detects a spark firing, it will flash the Super Bright LED strobe indicating a spark-firi ...more

Analysis for 3P4W, 3P3W, 1P2W, 1P3W True RMS value (V123and I123) Active Power (W, KW, MW, GW) Apparent and Reactive Power (KVA, KVAR) Power Factor (PF), Phase Angle Energy (WH, KWH, KVARH,PFH) current measurement from 0.1mA to 1000a, capable of analyzing IT standby power consumption to the maximum demand of a factory. Display of 35 Parameters in O ...more

The AVRQ-1-B provides a -1 kV pulse with a linear leading edge, followed by a slower exponential decay back to zero. The transition time (10%-90%) of the leading edge is variable from 50 ns to 500 ns. ...more

The 2925 is a 5 KV AC Hipot test with 12 mA of test current Equipped with the latest technology and features the 2925 is the right solution for almost any AC Hipot test application. ...more

The DigiVolt® series of digital voltmeters and phasing sets is designed to take voltage measurements and perform phasing applications on system voltages up to 80 kV. ...more

CWG 1.2/50 µs, 8/20 µs; Ring Wave, 100 kHz; ITU K17 10/700 µs. ...more

The 2510 is a 5 KV, 10 mA AC Hipot tester that is designed for production line AC Hipot testing. With its advanced features and product reliability it is well suited for quick and easy production line safety testing. ...more

Input Impedance: 600 Mohm Attenuation ratio: 40000:1 Accuracy: DCV (0-20KV) +-2%, DCV (20KV-40KV) +-3% Max. working Voltage: DC 40 KV Operation Temperature: 0 - 50 deg. C Storage Temperature: -10 - 60 deg. C Cable Length: 1 m Note: for positive polarity only, not ofr microwave ovens ...more

The affordable, versatile unit is perfect for routine checking of ionization system effectiveness. Its features include: Pocket-sized for instant availability. Dual-range meter for easy reading. Extra-wide 0 - +/-30 kV range. Recorder output and 40-hour battery life for unattended monitorin ...more

DC VOLTMETERS. DC KV Meter. 4.5 Digit Readout ...more

The AVRQ-2-B provides a -2 kV pulse with a linear leading edge, followed by a slower exponential decay back to zero. The transition time (10%-90%) of the leading edge is variable from 50 ns to 500 ns. ...more

Model 19, 21, 23 True RMS value (V and A) Leakage Current Measurement at 10uA resolution. Harmonic analysis (V and A ) to the 99the Order. Better Understanding of High Frequency Harmonic Analysis (up to 5/6 KHz). Non-interrupted Harmonic Analysis Analysis of Total Harmonis Distortion (THD-F) Analysis of Crest Factor (C.F.) Fast Peak Function (33 us ...more

The current reset 1CRD fault indicators' large, reflective display makes it an ideal choice for installation on overhead cables. When the system voltage does not meet the 5 kV minimum requirement of an electrostatic reset fault indicator but 3 A of continuous load current is present, the CRD is an excellent solution ...more

The Digital Voltage Indicator (DVI) is a single point instrument designed to read the voltage on a conductor up to 99kV line-to-ground. The large LED readout is easy-to-read on the end of a long hotstick and can be used on overhead lines or in underground applications with an optional probe. For use on system voltages up to 161 kV (99 kV line-to-gr ...more

The ESD 3000 is the only 32 kV ESD Simulator which is both battery operated and completely hand-held, eliminating base unit, external power supply, and power supply tether cable associated with other ESD simulators. ...more

Use SEL test point voltage reset fault indicators with remote tamperproof bold displays (1TPRB) on 200 and 600 A class underground distribution systems whose terminators have test points. The 1TPRB requires a 5 kV phase-to-ground minimum voltage to reset and remain ready to trip. Its remote bolt automatically resets when system voltage returns ...more

Compact & High-performance 20 % Reduction in Footprint Compared to the Current Model. VP Mode Standard. SE 3.0 nm Resolution at 30 kV, BSE 4.0 nm (6 Pa) Guaranteed. Accommodates Samples up to 152 mm (diameter) and 60 mm (height). Provides for Two EDX Symmetrical Ports. ...more

Instrument for circuit phasing / potential testing and URD cable testing. 0- 40 kV tester kit. ...more

The TAG-5000 Wireless Phaser provides a unique method of phasing across a single-phase or three-phase system to make certain that correct polarity has been established prior to "closing-in" a switch. Phase conductors on system voltages to 230 kV (phase-to-phase) ...more