Voltage Converters

The 28524 Quad Frequency-to-Voltage Converter Module provides conditioning for pulse, rate and frequency transducers. The 28524 gives a voltage output proportional to input frequency or rate for frequencies from 1 Hz to 50 kHz with inputs from 10 mV to 100 V. Distorted inputs such as signals with ringing, crossover or harmonic distortion are h ...more

The PX453S is a 16 or 32 channel 12-bit A/D converter that provides autonomous signal conversion using an on-board DSP to provide a programmable scan rate, gain/offset compensation, and storage of conversion results. The common-mode voltage inputs are optically coupled and have programmable input ranges. Each input has 1KHz anti-aliasing filter and ...more

The VTC120 Series Voltage Converter is a variable duty cycle switching power supply with a precision linear regulator output (except for the VTC120nr-12-24). This model is common negative. This means that the input negative (ground) connection and the output negative (ground) connection are common or tied together. Applications include running ...more

64 bit Hot Swap 66MHz, PCI/PCI-X extender card, 5V keyed top connector* 5V<=> 3.3V Signal Level Conversion Software programmable via parallel port to: ...more

Single output benchtop Power Supplies. Suitable for use as constant-voltage/ constant-current sources with automatic regulation of voltage-to-current transition (LED indication) and as battery eliminator with switch-selected delay for current regulation (higher surge current), eg for incandescent lamps, blinkers, voltage converters. Other feat ...more

As supply voltages proliferate (frequently to seven or eight per system board) and current levels soar (occasionally to >100 Amps), the economics of the new on-board distributed power architectures (DPA's) become more compelling. In particular, the Intermediate Bus Architecture (IBA) should be considered whenever you need three or more v ...more

Behlman's BL1350 AC Power Supply / Frequency Converter / Inverter, requires just 3.5" of rack height, and weighs just 40 pounds, yet it delivers 1350 VA of quality AC power. In the BL 1350, you'll find the quality features you expect from Behlman, fully adjustable frequency and voltage, total harmonic distortion of less then 0.5%, high ef ...more

When your application requires multiple positive voltages and you can not easily derive one from the other using a non-isolated POL, consider an asymmetric dual. Asymmetric duals are isolated, 2-output DC/DC converters that typically provide two low voltages such as 3.3V and 1.8V. As such, they are ideal for driving the core and I/O ...more

Behlman's P1350 AC Power Supply / Frequency Converter / Inverter, delivers 1350VA of clean, regulated AC power in a 3.5" high bench top unit, that easily converts to rack mount, for far less cost than competitive models. The Power Passport can simulate any world wide utility as well as aircraft and shipboard power. Simply select the requi ...more

64 bit Hot Swap 66 MHz, PCI/PCI-X extender card, 3.3V keyed top connector* 3.3V5V Signal Level Conversion Software programmable via parallel port to:  ...more

IP235 modules have a 16-bit D/A converter (DAC) to provide highly-accurate analog voltage outputs. An internal RAM buffer enhances control over the transfer of data to the DAC. ...more

IP230 modules have a 16-bit D/A converter (DAC) to provide highly-accurate analog voltage outputs. Jumper-selectable output ranges give you the choice of unipolar or bipolar voltage output. And for greater flexibility, the IP230 module accepts conversion start triggers from software commands, or from external sources for synchronization to spec ...more

These modules provide an isolated Profibus-DP network interface for six analog input channels. Differential inputs eliminate ground loops and thus the need for isolators in many applications. Multi-range inputs accept signals from a variety of sensor and devices. High-resolution, low noise, A/D converters deliver high accuracy and reliability. ...more

64 bit Hot Swap 66MHz, PCI/PCI-X extender card, 3.3V keyed top connector* 5V<=> 3.3V Signal Level Conversion Software programmable via parallel port to:  ...more

A custom, DORIC-designed, integrating voltage-to-frequency A/D converter combined with precision filtering, isolated electronics, and multi-segment digital linearizations lets the Series 600 accommodate wide measuring ranges at a very high resolution - high enough to achieve laboratory accuracy in process and test measurements. ...more

The DCX-127 Multifunction Module provides Audio Precision's PC-controlled audio analyzers with an interface toolkit of non-audio functions and interface capabilities that are often required in typical audio test applications. The module contains a 4-1/2 digit DC voltmeter-ohmmeter, two 20-bit programmable DC voltage sources, 21 bits of digital ...more

IP236 modules have 16-bit D/A converters (DAC) to provide highly-accurate analog voltage outputs. FIFO buffers enhance control over the transfer of data to the DAC and improve efficiency. ...more

The 1851 IN is a LCD indicated instrument for testing insolation (mW), continuity (W) and AC Voltage. Use of a high efficiency and accurate DC-DC converter. 3-1/2 digital LCD (2000 counts) 68x34mm large LCD display. Tests insulation at rated voltage into a 1mA load  ...more

Single output benchtop Power Supplies. Suitable for use as constant-voltage/ constant-current sources with automatic regulation of voltage-to-current transition (LED indication) and as battery eliminator with switch-selected delay for current regulation (higher surge current), eg for incandescent lamps, blinkers, voltage converters. Other feat ...more

Single output benchtop Power Supplies. Suitable for use as constant-voltage/ constant-current sources with automatic regulation of voltage-to-current transition (LED indication) and as battery eliminator with switch-selected delay for current regulation (higher surge current), eg for incandescent lamps, blinkers, voltage converters. Other feat ...more

Single output benchtop Power Supplies. Suitable for use as constant-voltage/ constant-current sources with automatic regulation of voltage-to-current transition (LED indication) and as battery eliminator with switch-selected delay for current regulation (higher surge current), eg for incandescent lamps, blinkers, voltage converters. Other feat ...more

Multiple output benchtop Power Supplies. NGL 35 has three equal, separate and floating outputs. The voltages can be independently adjusted between 0 and 35 V and the current limiting threshold between 0 and 0.6 A. Voltage or current ratings can be tripled by parallel or series connection. A switchable panel meter is provided for each output. ...more

These modules provide up to six channels of analog output. Multi-range outputs support  a wide variety of industrial devices. They can drive displays and recorders, control drives, or send analog signals to other systems. High-resolution, low noise, D/A converters deliver high accuracy and reliability. 3-way isolation further improves system pe ...more

PMC230 modules have eight 16-bit D/A converter (DACs) to provide highly-accurate analog voltage outputs. A unique two-piece board design brings the proven reliability of Acromag?s IndustryPack (IP) A/D modules to a PMC format. An IP230 module is embedded on a PMC interface card that maintains maximum performance and transparent communication to ...more

C&D's small size electronic loads range from 0 to 50A and 0.65 to 200V. Total power consumption is 100W with a heat sink. Their package size is 2" x 2" x 0.5" (51 x 51 x 12.7mm). The loads can be alternatively controlled by an analog controlled input or a serial input (any digital I/O board or RS-485 based options). Real-time load simulation, power ...more