Transceivers

The CR510 dataloggers are a smaller version of our popular CR10X dataloggers. They provide a lower-cost datalogger alternative for measurements of a limited number of sensors, yet can be used with most of our telecommunication devices such as cellular telephones, RF UHF/VHF RF modems, and satellite transceivers. The CR510-series dataloggers us ...more

The CX74063 transceiver is a highly integrated device for multi-band GSM/GPRS applications. The device requires a minimal number of external components to complete a GSM radio subsystem. The CX74063 supports GSM850, EGSM900, DCS1800, and PCS1900 applications. The receiver also supports downlink EDGE applications. The receive path implements a ...more

Finally the solution every field technician and equipment owner needs to quickly locate and resolve signal anomalies, dropouts and glitches that cause E84 handoffs to fail. This next generation recording device is a small self-contained unit that inserts between the passive equipment and PI/O transceiver to capture and write E84 handshakes to i ...more

The CX65003 PA driver offers a desirable combination of features that provide superb performance and ease of use in a low-cost SMT package. This GaAs HBT PA driver was developed and optimized for extreme linear performance in a variety of applications. It is ideal as a driver or output stage in transceivers and repeaters for WCDMA and CDMA2000 ...more

The PMC450 is a FPGA-based 8 channel RS422 serial card with front and rear I/O. The standard configuration consists of a PCI-core and eight 16C550-uart compatible cores. With the 32 onboard RS422 transceivers 8 serial RS422 channels (Rx, Tx, RTS and CTS) are created. The PMC450 features a 68-pin high dense connector at the front for the connect ...more

The CX65001 PA driver offers a desirable combination of features that provide superb performance and ease of use in a low-cost SMT package. This GaAs HBT PA driver was developed and optimized for extreme linear performance in a variety of applications. It is ideal as a driver or output stage for transceivers and repeaters for TETRA transceiver ...more

ISO and CIRC series narrow band junction isolators and circulators cover common communication and radar frequency bands from 8.2 to 110 GHz in 11 waveguide bands. The isolator is an ideal device where the port isolation is required, while the circulator is commonly used as a duplexer for transceiver subsystems where the transmitter and receive ...more

The SC105 Interface supports communications between a Campbell Scientific datalogger and an RS-232 DCE device. Common DCE devices used with the SC105 include our Raven100, Redwing100, and Redwing105 cellular transceivers as well as third-party radios and modems. The SC105 provides internal buffering that temporarily stores data. This allows th ...more

The RF312 is a Maxon UHF transceiver that supports the 440 to 470 MHz frequency range. This rugged transceiver can support up to 254 dataloggers on a single frequency. Each station can transmit up to 25 miles line-of-sight, and each station can act as a repeater to extend the transmission distance attainable by the network. ...more

The DATATRAC 650 is an ARINC 629 data bus analyzer that can be configured with up to three independent transceiver channels. Basic receive and transmit functions are implemented along with a general record mode and a breakpoint mode. ...more

MEIs Remote Motion Block (RMB) is designed to connect conventional analog drives into a SynqNet system. Each Remote Motion Block can support up to four axis of high precision analog drives, including encoder feedback, DAC outputs, transceivers, and associated I/O. [144K] ...more

The CX65002 PA driver offers a desirable combination of features that provide superb performance and ease of use in a low-cost SMT package. The GaAs HBT PA driver was developed and optimized for extreme linear performance in a variety of applications. It is ideal as a driver or output stage in transceivers and repeaters for AMPS/CDMA/TDMA/GSM ...more

The RS21101 baseband processor is part of the Skyworks PHS chipset, which also includes the RS21501 IF transceiver, RS23301 HBT power amplifier, and RS23603 RF transceiver. The RS21101 performs all of the baseband processing needed for the communication link, the ITU G.726 voice processing compression, and the PHS standard communication protoc ...more

The next generation of optical transceiver has arrived with the introduction of GCI's RJ-11 Optical Transceiver. This fully SEMI compliant and Hokuyo compatible unit is the choice of leading 300mm FABs and equipment manufacturers throughout the world to simplify installation and maintenance of their E84 communications. ...more

The RF416 spread spectrum transceiver has an operating frequency range of 2.45 to 2.46 GHz, which is used in many countries world-wide. The RF416 is a compact, rugged, low-cost transceiver intended for use in a variety of applications. The transceiver transmits at a power level of 60 mW and frequency-hops among 25 channels to avoid interferenc ...more

ISO and CIRC series narrow band junction isolators and circulators cover common communication and radar frequency bands from 8.2 to 110 GHz in 11 waveguide bands. The isolator is an ideal device where the port isolation is required, while the circulator is commonly used as a duplexer for transceiver subsystems where the transmitter and receive ...more

The RS23301 HBT power amplifier is part of the Skyworks PHS chipset, which also includes the RS21101 baseband processor, RS21501 IF transceiver, and RS23603 RF transceiver. The RS23301 typically consumes 130 mA at 3.4 V and provides an unconditionally stable design that removes the need to follow the PA with an RF isolator. The RS23301 offers ...more

The RS21501 low-current IF transceiver is part of the Skyworks PHS chipset, which also includes the RS21101 baseband processor, RS23301 HBT power amplifier, and RS23603 RF transceiver. The RS21501 provides up and down conversion between baseband and RF transceivers. The RS21501 generates a 10.75 MHz modulated carrier and upconverts to 248.45 M ...more

The M301 provides two asynchronous serial interfaces based upon the MC68681 DUART. The line interface of a channel can be configured as RS232, RS422, RS485 or current-loop (active or passive). The RS232 and RS485 transceiver devices are commonly available and are mounted in sockets for easy maintenance.  ...more

The P-10SF from Condor Engineering offers one or two channels of dual-redundant 10Mbit 1553 Notice 2 protocol using RS-485 transceivers. ...more

Over the past 5 years, the trend in optical communications has seen a migration to hot pluggable transceiver modules. These modules are self-contained transmitters and receivers that offer significant advantages over discrete optics. These advantages (smaller footprints, added functionality and control firmware) have resulted in an increase in the ...more

The CX74017 transceiver is a highly integrated device for multi-band GSM, GPRS, or EDGE applications. The device requires a minimal number of external components to complete a GSM radio subsystem. The CX74017 supports GSM850, EGSM900, DCS1800, PCS1900, and downlink EDGE applications. ...more

GCI's industry leading E84 diagnostic software is a powerful, Windows-based graphical analysis application that can upload and analyze data from GCI's E84 Handheld Tester, E84 DLD, and RJ-11 Optical Transceiver products. The E84 Analysis Application can also display the signals of a live material handoff in real-time when connected to GCI's E84 DLD ...more

The 7140 is a software radio transceiver suitable for connection to HF or IF ports of a communications system. It includes two A/D and two D/A converters capable of bandwidths to 40 MHz and above. ...more

The MC432 serial RapidIO 8-port switch IC has 8 ports of 4x lanes, allowing developers to take advantage of the benefits of serial RapidIO technology for embedded, communications, networking, and storage applications. The switch provides 64 Gb/s of bandwidth, and each port has four full-duplex serial transceivers. ...more