Showing results: 511 - 525 of 5297 items found.
-
Banair
This is a high specification tester that will measure many cable parameters. It measures cable resistance very accurately using the Kelvin 4-wire method. It also tests for shorts between pins at a low voltage. The next test is to measure insulation between connections at a higher voltage. This is carried out at up to 1500 Volts DC with resistances of 10 to 500 Meg ohms.
-
EUROSMC, S.A.
The Raptor system consists of a main ‘master’ unit and a number of optional units that enable the execution of virtually any commissioning or routine testing jobs on the primary equipment of medium and high voltage electricity installations.
-
Chroma ATE Inc.
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
System 1828 -
Pulse Instruments
The basic system consists of a 225 MHz pattern generator, 10 clock drivers, 6 DC biases, 1-4 channels of 10 MHz 14 bit analog data acquisition and/or 1-4 channels of digital acquisition. Additional options can be added to customize the system to meet your requirements.
-
LM Series -
Koyo Electronics Industries co., ltd
Models in LM-2100 series equipped with LCR meter are designed to measure inductance and dissipation factor of the coil to which DC current is superimposed. Special circuit is built in to protect the LCR meter from surge voltage. Applied current can be step by step in the remote mode. Voltage application is impossible with the safety cover open.
-
Averna
Need to manufacture test stations? For more than 15 years we have sourced, assembled, tested and shipped fleets of robust, cost-effective solutions. We produce them at our high-volume facilities and deploy them around the world.
-
-
C8900 -
Chroma Systems Solutions, Inc.
The 8900 electrical equipment ATS can complete measurement and test procedures simultaneously and automatically. This automated functionality decreases the risk of errors due to improperly written tests. Chroma 8900 solves the Electrical Safety Test and special FUNCTION test solution.
-
CTTS Series -
Shanghai Jiuzhi Electric Co., Ltd.
CTT series cable test terminations are used to test Plastic insulated high-voltage cables. The specific advantages of this series versus conventional terminations are fast and convenient assembly. The terminations can be used for partial discharge (PD) measurements, impulse voltage testing, loss factor (tan delta) measurements and, if the cable ends are carefully prepared, for breakdown testing (step test).
-
Cincinnati Test Systems
Vacuum leak testing is the principal leak test method for testing parts that could have leakage from an external source into their housings and casings. Parts like underwater sensors or housings, outdoor electrical housings, sealed components, and components associated with vacuum sources are all prime candidates for vacuum leak testing. Operation of instruments that supply vacuum to test parts instead of pressure works in a similar, yet essentially opposite, manner as pressure decay testing.
-
Premier Electrosystems
Premier Electrosystems' Thermal Stability Test Setup is used to test thermoplastics and PVC (Plasticized Polyvinyl Chloride) materials. When exposed to continuous heat, these materials degenerate and emit harmful acidic gases. The instrument is manufactured for testing PVC materials for their thermal stability at higher temperature.
-
G-3 Series -
Shinken Co. LTD.
This series was used for the special structure of airbearing guide of inspection for Seismic Detectors andcharacterized is large displacement and high-accuracywaveform. In addition, the use of the Windows seismicdetector controller is easy to operate it.
-
i-series -
IMV Corporation
Vibration tests have become diversified and specifications have become increasingly strict.i-series offer a user-friendly lineup with enhanced performance and durability.
-
WonATech Co.,Ltd
For 100Watt DMFC single cell testCompact sizeConsists of electronic load, gas/liquid controller, humidifier and methanol pump etc.
-
LD-LGST-A10 -
Labodam
Gel Strength Test SystemLD-LGST-A10is mainly used to measure the gel strength of gelatine under the stipulated environment. It has traveling accuracy ± 0.3 % and Test range up to 5 to 1000 g Bloom. It consists of Jelly Strength Tester, Constant Temperature Bath and Refrigerator. Sampling depth can be present arbitrarily in 1 to 60 mm. It consists four kinds of sampling measurement modes: single-step, maintaining, circulating and automatic.