TEM Cells

KL-167 intellectual acidometer is an accurate electrochemical apparatus which is used to measure the sodium ion and basicity, electrode potential and the temperature of solutions.It is an accurate secondary instrument with LED digital display. It can be used with various ion selective electrodes to measure cell potential of electrodes in solut ...more

CX77315, a quad-band PA module designed for cellular handsets comprising GSM850/900,DCS1800, and PCS1900, also supports Class 12 GPRS multi-slot operation. It consists of separate GSM and DCS/PCS PA blocks, impedance-matching circuitry for 50 ohm input/output, and a PAC block with an internal current-sense resistor. The GaAs die, the Si die, a ...more

The new Model CT485B completely self-contained temperature/ relative humidity recorder is microprocessor based to accurately measure, indicate and record temperature and relative humidity. This rugged unit comes standard with alarms. They contain a single, integral relay contact which closes in response to an alarm condition. Simultaneous high and ...more

The UV-VIS-NIR spectrophotometer provides a total capability for spectral analysis of materials and components of DSC. Its major roles are in the analysis of dyes, dye adsorption and electrolytes. Options of large sample compartment, constant-temperature and ultra-micro cell holders enable a wide range of measurement possibilities. ...more

The University Test Station provides control of flow, temperature and pressure for the anode and cathode gases. The station incorporates a DC electronic load. The Station also includes two humidity bottles, an Operating Manual and a computer utilizing LabView-based software. ...more

Our SOFC test stations are integrated measurement, testing and analysis systems, designed for the unique needs of the SOFC market. These systems include gas mixing, humidification, pre-heating, furnace, heat recovery and water balance modules. Systems can operate on gaseous or liquid fuels. Operating temperatures range up to 1000°C and operating pr ...more

A low cost manual test station which includes a gas management unit and an electronic load with voltage and current displays. System incorporates independent gas flow control of reactant mixtures, cell temperature control, and dynamic load control. ...more

The Fuel Cell Test Stations provides control of flow, temperature and pressure for the anode and cathode gases. The station incorporates a DC electronic load. The Station also includes two humidity bottles, an Operating Manual and a computer utilizing LabView-based software. ...more

The TEMpact GHz TEM Cell was developed especially to permit EMC radiation testing of smaller EUT (equipment under test) in a shorter time and at a lower price. In addition to the comparatively low purchase price of the cell itself, the cost incurred by the necessary measuring equipment, too, will be reduced. Another advantage is the little spa ...more

The Evaluator series “HT” (High Temperature) is specially designed for testing solid-electrolyt fuel cells (solid oxide fuel cells or SOFC) with maximum temperatures of 1,000°C. The test stations can be used for characterization of components, the evaluation of SOFC single cells, stacks, complete systems and hot-box systems as well as for optimiz ...more

Combination rugged flat surface pH electrode with autoranging high accuracy Conductivity cell. Measures 5 parameters including Conductivity, TDS, Salinity, pH, and Temperature using one electrode. 9 units of measure: pH, µS/cm, mS/cm, ppm, ppt, mg/L, g/L, °C, °F  ...more

The SHD033 matches the sensitivity of a PMT using solid state amplification of a silicon photodiode. The proprietary preamp is unique in that it preamplifies the current-chopped junction charge of the cell, providing an 82 dB linear response. Built-in temperature control and leakage shielding minimize noise and dark current.  ...more

CONIMED Model TD50 / LS is an integrated system to perform tan delta tests on insulating materials like transformer oil. The test cell supplied fulfills requirements of Standards IEC 247 and 250, and ASTM D924 and D150. The test cell is normally used together with the digitally controlled thermostatic bath Model TB110, that allows tests to be ...more

MODEL TL6 Intelligent Test Load for Batteries and Fuel Cells is a passive electronic load with built-in microprocessor intelligence, with ability to briefly interrupt the current and take resistance free potential readings with a programmable delay. There are additional inputs, for a reference and for up to three temperature sensors. An expansi ...more

Combination rugged flat surface pH electrode with autoranging high accuracy Conductivity cell. Measures 5 parameters including Conductivity, TDS, Salinity, pH, and Temperature using one electrode. 9 units of measure: pH, µS/cm, mS/cm, ppm, ppt, mg/L, g/L, °C, °F  ...more

DP80 Series digital indicators offer complete expandability to effectively meet your changing needs. A custom designed, integrating voltage-to-frequency A/D converter combined with precision filtering, isolated electronics, and multi-segment digital linearizations lets the DP80 Series accommodate wide measuring ranges at a very high resolution - hi ...more

Precision Design Systems can build to print or custom design and manufacture Test Equipment to your specifications. Liquid or Gas Flow Test Systems, Pressure & Temperature Test Systems, Leak Test Systems, Electronic Load Test Systems, Automation Assembly Test Systems, Fuel Cell Test Systems, Vision Test Systems and DAQ Systems. ...more

MODEL TL5 Intelligent Test Load for Batteries and Fuel Cells is a passive electronic load with built-in microprocessor intelligence, with the ability to briefly interrupt the current and take resistance free cell potential readings with programmable delay. There are additional inputs for a reference electrode and for a temperature sensor. ...more

The electromagnetic simulation software CST STUDIO SUITE is the culmination of many years of research and development into the most efficient and accurate computational solutions to electromagnetic design. CST MICROWAVE STUDIO (CST MWS) is a specialist tool for the fast and accurate 3D EM simulation of high frequency problems. CST EM STUDIO(CST EMS ...more

A pocket solution for all RF power measurements.PMM 6600 is a simple and easy-to-use RF power meter mainly designed for EMC applications in order to calibrate CDNs and CLAMPs for conducted immunity systems or to measure the input power forwarded to antennas or cells. Using a bidirectional coupler and two PMM 6600 it is possible to measure the r ...more

SADC(Sensor A/D Converter) series A/D converter module providing high accuracy "instrument" grade perpormance for sensor measuring application, including temperature, pressure, load cell, strain-gauge... the SADC integrate the A/D converter and linerization function in the same device, in most case, for sensor whose transfer functio ...more

EMS, EMI, measurement for sensitivity of RF communication equipment, calibration of E-field probe and IC circuit test. ...more

The Evaluator series “LT” (Low Temperature) is typically used for testing polymer-electrolyte (PEM) and direct-methanol (DMFC) fuel cells with maximum temperatures of 130°C. For testing high temperature PEM fuel cells, we offer options with maximum temperatures of 180°C or 250°C. ...more

The Lab-Pro “Flexible Test System” by PDS provides test plans designed to perform accelerated testing, by means of elevated or decreased temperatures, increased electronic loads, varying fuel flows and compositions. PEM, SOFC, DMFC, MCFC Test Systems. ...more

QUICKCELL QC200 is an electrochemical test cell designed for testing of gas diffusion or solid electrodes in controlled laboratory environment in fuel cell and battery R & D and quality control. Electrode coupons of 5 cm2 area are very easy to mount. Electrolyte in the cell reservoir is maintained at desired temperature by means of a circul ...more