Surge Generators

The SWG series surge generators are designed with switchable, multi-stage surge capacitors and three (3) voltage ranges. This design offers a substantial advantage over single stage capacitor units by allowing the user to minimize the surge voltage and maximize the surge energy and fault current. ...more

Surge impulse generators over 8kV are designed for applications ranging from component testing and EMC tests through to Lightning simulation in radio antennas. Typical standard applications include IEC, ITU and ANSI for power line testing, ITU and UL for component testing and ETSI for telecommunications testing. ...more

In conjunction with T-602 Audio Frequency Generator or T-302 HV Surge Generator, to quick and precisely pin point high/low resistance and flashover fault position for power cable, and detect the cable path and depth ...more

Telecommunication networks are exposed to lightning events. Therefore telecommunication equipment being connected to the outside world need to have appropriate protection to show an acceptable immunity to surge transients in order not to fail in case of lightning events. Telecom Surge Simulators of the TSS 500 series are used to proof the immunity ...more

Recurrent Surge Generator 482 is a bench-top, one stage, low voltage equivalent of a high voltage impulse generator. Its wide range of applications includes the testing of models, the study of voltage distribution in high voltage windings during impulse voltage stresses and the predetermination of the circuit parameters of impulse test plants. ...more

The SURGE TEST GENERATOR PG 10-1520 has been designed for testing two-gap over-voltage protectors. It delivers surge current pulses synchroneous at two impulse current outputs, wave form 8/20 µs, peak value adjustable 0.2 - 10 kA for each output. ...more

The high-current pulse generator PG 6-2402 is designed for surge current testing of electrical components, over-voltage protectors and electronic circuits acc. to IEC, VDE etc. It generates standard impulse currents with waveform 8/20µs. Pulse current output amplitude can be set to 2 - 50 kA. ...more

The Electromagnetic Impulse Detector has been designed to localize faults on buried cable by detecting the magnitude and polarity of current established on a cable during surging with a surge generator. ...more

The surge current generators PG **-*** generate standard impulse currents with wave form 8/20 µs according to IEC, EN, VDE. Pulse current output amplitude is controlled by preset charging voltage and can be adjusted up to the maximum value of the special type of generator. The generators are designed for testing electrical components, overvolta ...more

The SURGE TEST GENERATOR PG 10-1520 has been designed for testing two-gap over-voltage protectors. It delivers surge current pulses synchroneous at two impulse current outputs, wave form 8/20 µs, peak value adjustable 0.2 - 10 kA for each output. ...more

The surge current generators PG **-*** generate standard impulse currents with wave form 8/20 µs according to IEC, EN, VDE. Pulse current output amplitude is controlled by preset charging voltage and can be adjusted up to the maximum value of the special type of generator. The generators are designed for testing electrical components, overvolta ...more

The surge current generator PG 2-750 delivers pulse currents with the waveform 10/160µs and 10/560µs. Optionally an additional waveform, 10/1000µs can be integrated. The generator has four or two surge current outputs. ...more

While pin pointing faults in underground cables, a surge generator in the timing mode is made to dissipate high voltage energy surges into the cable. The resultant breakdown gives rise to magnetic signals throughout the route of cable and acoustic signals around the point of fault.   ...more

The High-Voltage Pulse Generator IPG 255 is designed for testing of impulse dielectric strength of components, insulation, air-and surface flash-over gaps of watt-hour meters, static relais etc. according to IEC 255, EN 61036, VDE 0435 Teil 303. ...more

The high-current pulse generators PG 6-200 / PG 6-400 are designed for surge testing of electrical components, over-voltage protectors and electronic circuits acc. to IEC, VDE etc. They generate standard impulse currents with waveform 8/20 µs. Short circuit output current amplitude is selectable from 0.2 up to 10 kA by adjustment of the chargin ...more

The surge current generators PG **-**** generate impulse currents with wave form 10/50 µs - 10/1000 µs acc. to IEC, VDE etc.. Pulse current output amplitude is controlled by preset charging voltage and can be adjusted up to the maximum value of the special type of generator. The generator is designed for testing electrical components, overvolta ...more

The surge current generators PG **-*** generate standard impulse currents with wave form 8/20 µs according to IEC, EN, VDE. Pulse current output amplitude is controlled by preset charging voltage and can be adjusted up to the maximum value of the special type of generator. The generators are designed for testing electrical components, overvolta ...more

HV - Impulse generators IPG 620 and IPG 1050 create standard impulse voltages with wave form 1.2 / 50 µs acc. to IEC 60. The generators simulate surges caused by switching of inductive loads, power system switching, lightning strokes etc. ...more

The Surge Test Generator PG 6-432 produces impulse currents with standard wave forms 10/700 µs or 10/1000 µs. Testing two-gap overvoltage protectors the generator delivers simultaneous at two outputs impulse currents adjustable up to 100 A each. ...more

Full Compliance CE Mark test equipment and ANSI transient test solutions. Choice of 4kV or 6kV SURGE generators with Combination, 100 kHz Ring, and 10/700 waves plus your choice of ESD, EFT, and voltage DIPS and Interrupts as needed. Integrated, automated, single phase CDN. ...more

The LSS-15AX series have been newly designed to completely satisfy and exceed the requirements in IEC 61000-4-5 standard. The simulators consist of a combination wave generator applying a 1.2/50 open-circuit voltage wave in a high impedance test piece and delivering an 8/20 short-circuit current wave in a low impedance test piece, CCITT telecom wav ...more

HV - Impulse generators IPG 620 and IPG 1050 create standard impulse voltages with wave form 1.2 / 50 µs acc. to IEC 60. The generators simulate surges caused by switching of inductive loads, power system switching, lightning strokes etc. ...more

The surge current generators PG **-*** generate standard impulse currents with wave form 8/20 µs according to IEC, EN, VDE. Pulse current output amplitude is controlled by preset charging voltage and can be adjusted up to the maximum value of the special type of generator ...more

The high-current pulse generator PG 6-2402 is designed for surge current testing of electrical components, over-voltage protectors and electronic circuits acc. to IEC, VDE etc. It generates standard impulse currents with waveform 8/20µs. Pulse current output amplitude can be set to 2 - 50 kA. ...more

Line Interactive System 350 VA ? 3000 VA  Line interactive design  Cold start function  SMD technology  Compatible with generators  Boost and buck AVR  Cutoff when no load connected  Intelligent battery management  Automatic self-detection on startup  Fully digitized microprocessor control  Lightning and surge protection ...more