Surge Generators

Surge generators of the PS-Line series are used for cable testing and fault location in low and medium voltage networks. With the PS - Line InterEng offers a series of surge generators wich are easy to operate. The surge voltage is continuously adjustable between "0" and the maximum voltage of the selected voltage level. The surge generators are av ...more

EMC Partner Watt-hour-meter Insulation Tester is a patent pending generator designed for different tests: Insulation test on capacitive loads as insulation material, air insulation, gas insulation etc. waveform 1.2/50µs up to 12kV with a serial resistor of 40 Ohm, current limited with 40 Ohm; Insulation test on capacitive and inductive loads a ...more

EMC PARTNER offers a series of standardized MIG generators for surge withstand tests to cover up to 6 kV charging voltage range: MIG0606: 6kV, 2 x 3kA, Imax 6kA. MIG0612: 6kV, 4 x 3kA, Imax 12kA. MIG0624: 6kV, 4 x 6kA, Imax 24kA  ...more

This compact acoustic headset, designed and manufactured by K&S Engineering and Scientific Ltd has been developed with state-of-the-art components to not only to achieve superior performance but also to offer the user an acoustic headset that is smaller than equivalent units currently available on the market. Housed in an IP67 enclosure, t ...more

The instrument is fully enclosed in a robust all steel enclosure mounted on castors and fitted with carrying handles. The control panel forms the top of the case, it is finished in high gloss light blue stoving with cutter engraved labelling, and is protected by a detachable lid. The EHT outlet is of a recessed type designed to prevent accident ...more

Frequency range 50 mHz to 10MHz. Surge- and short-circuit-proof output. Highly accurate digital frequency display. Rise and fall time typ. 15 ns ...more

Full Compliance CE Mark test equipment and ANSI transient test solutions. Choice of 4kV or 6kV SURGE generators with Combination, 100 kHz Ring, and 10/700 waves plus your choice of ESD, EFT, and voltage DIPS and Interrupts as needed. Integrated, automated, single phase CDN. ...more

The Galaxy 4000 separates itself from other UPS modules with technology that increases performance and reliability, all at a competitive cost. The Galaxy 4000’s IGBT rectifier significantly minimizes input harmonics and the Power Factor Corrected Input reduces installation costs thanks to smaller cabling and generator costs. Unmatched fr ...more

Full Compliance CE Mark test equipment and ANSI transient test solutions. Choice of 4kV or 6kV SURGE generators with Combination, 100 kHz Ring, and 10/700 waves plus your choice of ESD, EFT, and voltage DIPS and Interrupts as needed. Integrated, automated, single phase CDN. ...more

The LSS-15AX series have been newly designed to completely satisfy and exceed the requirements in IEC 61000-4-5 standard. The simulators consist of a combination wave generator applying a 1.2/50 open-circuit voltage wave in a high impedance test piece and delivering an 8/20 short-circuit current wave in a low impedance test piece, CCITT telecom wav ...more

HV - Impulse generators IPG 620 and IPG 1050 create standard impulse voltages with wave form 1.2 / 50 µs acc. to IEC 60. The generators simulate surges caused by switching of inductive loads, power system switching, lightning strokes etc. ...more

The SURGE TEST GENERATOR PG 10-1520 has been designed for testing two-gap over-voltage protectors. It delivers surge current pulses synchroneous at two impulse current outputs, wave form 8/20 µs, peak value adjustable 0.2 - 10 kA for each output. ...more

Voltage 200 V to 4400 V. Waveshape 1,2 / 50 µs. Current 100 A to 2200 A. Waveshape 8 / 20 µs. Measurement of voltage and current during the discharging. 1phase coupling network 16 A include ...more

The high-current pulse generator PG 6-2402 is designed for surge current testing of electrical components, over-voltage protectors and electronic circuits acc. to IEC, VDE etc. It generates standard impulse currents with waveform 8/20µs. Pulse current output amplitude can be set to 2 - 50 kA. ...more

The High-Voltage Pulse Generator IPG 1201 is designed for testing of impulse dielectric strength of components, insulation, air-and surface flash-over gaps. It is specially used for testing surge withstand capability of insulation between accesible parts and hazardous live parts, e.g. terminals for connection of antenne and mains supply tremina ...more

The surge current generator PG 2-750 delivers pulse currents with the waveform 10/160µs and 10/560µs. Optionally an additional waveform, 10/1000µs can be integrated. The generator has four or two surge current outputs. ...more

While pin pointing faults in underground cables, a surge generator in the timing mode is made to dissipate high voltage energy surges into the cable. The resultant breakdown gives rise to magnetic signals throughout the route of cable and acoustic signals around the point of fault.   ...more

The high-current pulse generators PG 6-200 / PG 6-400 are designed for surge testing of electrical components, over-voltage protectors and electronic circuits acc. to IEC, VDE etc.  ...more

The Surge Test Generator PG 6-432 produces impulse currents with standard wave forms 10/700 µs or 10/1000 µs. Testing two-gap overvoltage protectors the generator delivers simultaneous at two outputs impulse currents adjustable up to 100 A each. ...more

The SURGE TEST GENERATOR PG 10-1520 has been designed for testing two-gap over-voltage protectors. It delivers surge current pulses synchroneous at two impulse current outputs, wave form 8/20 µs, peak value adjustable 0.2 - 10 kA for each output. ...more

The high-current pulse generator PG 6-2402 is designed for surge current testing of electrical components, over-voltage protectors and electronic circuits acc. to IEC, VDE etc. It generates standard impulse currents with waveform 8/20µs. Pulse current output amplitude can be set to 2 - 50 kA. ...more

The surge current generators PG **-*** generate standard impulse currents with wave form 8/20 µs according to IEC, EN, VDE. Pulse current output amplitude is controlled by preset charging voltage and can be adjusted up to the maximum value of the special type of generator. The generators are designed for testing electrical components, overvolta ...more

The SURGE TEST GENERATOR PG 10-10000 delivers surge current pulses with the waveform 8/20µs, acc. to IEC 60. It was designed for testing surge protection devices. Moreover the generator can be used for testing two-gap over-voltage protectors. It delivers surge current pulses synchroneous at two impulse current outputs, peak value adjustable 0.5 ...more

The surge current generators PG **-**** generate impulse currents with wave form 10/50 µs - 10/1000 µs acc. to IEC, VDE etc.. Pulse current output amplitude is controlled by preset charging voltage and can be adjusted up to the maximum value of the special type of generator. The generator is designed for testing electrical components, overvolta ...more

The VARISTOR-TESTER PG 6-250 is a compact test generator for testing the surge current capability of varistors. The unit contains a combination wave generator and a surge voltage generator acc. to CCITT, ITU-T.  ...more