Signal Conditioners

The 6060 is a two-channel signal conditioning amplifier-digitizer module with 50 kHz or 100 kHz bandwidth and both digitized and analog outputs. The bridge input is ten-wire shielded with programmable constant voltage or constant current excitation and programmable completion for quarter, half and full bridge transducers. Automatic bridge bala ...more

The Series SCC Signal Conditioners provide maximum accuracy with minimal cost. Built-in microprocessor digitally scales, amplifies, linearizes and isolates thermocouple, RTD, current, voltage, frequency or potentiometer analog input signals. Units offer 16-bit input resolution with 0.05% full scale accuracy. Eliminate ground loops with 1500 VA ...more

28454A Quad Conditioner with Balanced Current Excitation accommodates single arm static or dynamic strain gages, RTDs or other resistive transducers that require constant current to excite them. A unique balanced excitation circuit delivers accurate current yet has excellent immunity to noise pickup. Dynamic strain measurements may be made usi ...more

28104A Quad Bridge Conditioner offers four channels of conditioning to support a wide variety of transducers including those that require constant voltage excitation in a bridge configuration such as strain gages and pressure transducers. The 28104A is easily configured to operate as a precise voltage filter/amplifier on low-level AC or DC vol ...more

The 28208 Octal Thermocouple Conditioner provides eight channels of conditioning for thermocouples or other DC and AC voltage inputs. The 28208 consists of a low-drift programmable differential pre-amplifier, a 3-pole programmable filter and a programmable post-amplifier. A rugged remote isothermal block with digital temperature sensor provide ...more

28314 Quad Channel Wideband Charge/IEPE Conditioner provides signal conditioning for both Charge or IEPE type sensors. The 28314 features 200kHz filtered and 500kHz wideband bandwidth for shock and vibration applications. In Charge mode, ultra low drift and very large time constant circuits allow for both quasi-static charge measurements and a ...more

The 28316B 16-Channel Long Distance TEDS/IEPE Accelerometer Conditioner provides signal conditioning for either TEDS equipped or traditional IEPE sensors. Ideal for modal and structural analysis applications, the 28316B card is equipped with Precision Filters? long-distance TEDS (LDTEDS) technology that extends communication with TEDS equipped ...more

The NEW Krohn-Hite Model 39128 Multichannel Filter/Signal Conditioning System is a mainframe chassis that houses up to sixteen, 8-channel plug-in filter/amplifier cards providing as many as 128 channels of cost effective signal conditioning over the frequency range from 1Hz to 100kHz. Each plug-in card can be a filter, an amplifier or a mix of ...more

The V385 is a VME/VXI compatible eight-channel strain-gage signal conditioner applicable to generic bridge-type transducer applications. The V385 adds individual remote-sensed excitation supplies to each channel, increasing its precision over the Model V380's single excitation supply. Key to the V385's increased precision is a separate remotel ...more

Calex Mfg. Co., Inc. of Concord California announces the availability of the Model 163MK Strain Gage Signal Conditioner. The 163MK offers a complete turn-key signal conditioning solution for virtually any strain gage based measurement. ...more

The Scott G Series is a nest-housed type signal conditioners with AC/DC dual power supply, switch selectable output. The lineup includes pneumatic-electro transducers. ...more

High-performance, microprocessor controlled signal-conditioning amplifiers are used for transducer data acquisition. Advanced features include automatic zero, balance and calibration, computer monitoring and display of excitation and output, operator warnings for out of limit conditions, and digital data storage for transient and waveform capt ...more

Daytronic has four product families, the 2000 Series, the 3000 Series, the 3500 Series and the 4000 Series, designed to serve as Signal Conditioners and Controllers. Completely stand-alone in nature, these units can provide a low-noise system front-end, autonomous application control, operator display interfacing, remote data acquisition and s ...more

Barometric pressure is sensed by an integrated silicon absolute presure sensor with internal temperature compensation. The sensor is mounted to the signal conditioner board. A 3/16 inch diameter tube may be attached to the sensor to provide remote pressure sensing. The output of the sensor is scaled to provide the desired output signal. ...more

Calex Mfg. Co., Inc. of Concord California announces the Model 4800 load cell signal conditioner. The model 4800 is unique in that it incorporates the load cell summing board function with an amplier, filter and power supply for a complete turn-key conditioning system for hopper weighing, scales, tank farms, etc. ...more

Measuring linear signal 0~10V / 0(4)~20mA in one converter. Accuracy: +/-0.04%; 4 1/2 Digital display: -19999~29999. User function, Easily programmable via the front panel. 1 Relay ...more

The D Series is DCS-supported signal conditioners, consisting of modular type signal converters with versatile I/O specifications and housing nest. ...more

Literally, this means a signal adjuster receiving voltage or current source outputs from sensors to adjust so that the signals are outputted for measuring them. The basic functions of them are to change the physical volume to voltage using the sensor, amplify the minute voltage and insulate inputs/outputs ...more

The 906 Standard and the 907 Explosion-proof Hall Effect sensors produce digital pulse signals for use with speed switches, tachometers, counters, signal conditioners, or as direct pulse generators. ...more

The M Series bring Yokogawa performance and reliability to the popular plug-in style. Plug-in type construction provides easy for instrumentation planning, field wiring and maintenance. ...more

W Series signal conditioners have the terminals on the front panel. The microprocessor based models provide field configuration capability and minimum stock of spares ...more

The CSG110 Signal Conditioner Amplifier featured with Din Rail Mount is FUTEK?s solution for in-line amplifier of any full bridge strain gauge type sensor with mV/V range output to provide VDC and/or 4-20mA signal with built-in regulated bridge excitation source. The Strain Gage Amplifier has a plastic housing with mating DB9 female connector f ...more

Daytronic has four product families, the 2000 Series, the 3000 Series, the 3500 Series and the 4000 Series, designed to serve as Signal Conditioners and Controllers. Completely stand-alone in nature, these units can provide a low-noise system front-end, autonomous application control, operator display interfacing, remote data acquisition and s ...more

The V380 is a VME/VXI compatible eight-channel strain-gage signal conditioner which is optimized for load-cell weighing applications. The module includes tare (zero reference), DSP-based high-order filtering, averaging, triggered weighing, and other functions not commonly available in conventional strain-gage signal conditioners. Filtering and ...more

The IHH300 Portable Signal Conditioner with Digital Display is FUTEK?s solution for applications where a hand held instrument is required. The IHH300 has a fast response with 8000 samples per second, accepts plug and play with smart chip sensors, and 5 selectable filter settings (170, 250, 500, 1500, 3600 Hz) . ...more