Shakers

IGBT technology amplifier module for the HPA-K, SPA-K and DPA-K amplifiers that power LDS electrodynamic shakers. ...more

Designed for use with water-cooled electrodynamic shakers, DPA-K amplifiers offer a maximum power output of 280kVA and provide optimum performance for your vibration test system ...more

Testing of large structures can often present considerable difficulties, so when the payload can’t be mounted on the shaker GW can provide a shaker that can be mounted on the payload. Inertial shakers have found applications testing car chassis, building structures, ships’ flight decks, helicopters, submarines, geophysical surveys and vibration can ...more

Our quiet electrodynamic shakers support industry standard QA practices for Squeak and Rattle vibration testing, ensuring automotive components and interiors remain durable and free from noise. ...more

Trialon's mechanical testing capabilities include Vibration, Shock, Squeak and Rattle, Tensile Strength, Compression Force, and various component level pull, bend and torque tests. Our vibration lab is state-of-the-art with PC controlled shakers which can simulate actual road vibration conditions. ...more

These shakers all produce 50mm displacement (the V53 may provide 63mm) and all are air cooled. All models may be supplied on high quality pneumatic mounts, for vertical vibration isolation, in trunnions for horizontal and vertical operation, or in monobases for three axis testing using a slip plate. ...more

LDS's permanent magnet electrodymanic shakers are designed for vibration test applications including modal and structural analysis, separation and compacting of powders, and small component vibration screening. They are also ideal for use in accelerometer calibration. ...more

Water-cooled, electrodynamic shaker built for use with vibration tables capabale of testing large payloads such as satellites, aerospace assemblies and munitions up to 5 tonnes mass with a maximum sine force rating of 90 kN (20000 lbf).  ...more

GW has designed a special series of shakers for use in testing structures when the axial stiffness is required to be very low. When these modal shakers are driven in a constant current mode both mechanical and electrical damping are reduced to virtually zero and the phase shift between amplifier current and output force will be reduced to typically ...more

The V8 vibration test system offers the highest achievable envelope of vibration test parameters for an electrodynamic shaker: maximum displacement, velocity and force are all available at the same time.  ...more

Medium shakers are the workhorses for many component testing applications such as automotive assemblies and consumer electronics equipment. The range includes two shaker models with axial guidance bearings and 50mm displacement (V1322 and V617) and three models with flexure guidance and 25mm displacement. ...more

REXMED is one of the professional manufacturer and exporter of medical and laboratory equipment in Taiwan. Looking for any medical and laboratory equipment, suction unit, autoclave unit, sterilizing container, operating table, delivery table, stretcher, operating lamp, treatment unit, treatment chair, orthodontic equipment, bath, shaker, fermentor, ...more

he small range of shakers has found many applications, including use during several NASA space missions, medical / clinical applications, materials analyses and the testing of electronic or mechanical components. The force range begins with the model V2, which produces 9N, and extends through four permanent magnet models to the V100 and V300, which ...more

The LDS V9 electrodynamic shaker is designed to test heavy loads at high levels over long continuous periods. It uses a revolutionary design of two magnetic gaps driven by one field coil to provide displacement up to 75 mm (3 in) with a peak velocity of 3 m/s (118 in/s ...more

Inertial Measurement Units (IMUs) and sensor clusters using MEMS components consume less than 0.6 watts of power and have a mass under 60 grams. For micro and nanosatellite systems as well as UAV, AUV, ROV and automotive applications, etc. Other more sensitive platforms are also in work. Inertial Measurement Units - suitable for dead-reckoning duri ...more

Vibration testing determines the dynamic effects on component part of vibration within the frequency ranges and magnitudes that may be encountered during field service. ...more

If your unit under test has been mounted on a shaker once, it can be tested in any combination of vertical and horizontal direction. We can offer a most suited system to your specific application such as transportation tests of packaged freights, electric home appliances and OA equipment based on a test standard. The digital vibration control ...more

SignalCalc 350 is a low-cost Vibration Controller that provides the basic modes of vibration testing: Random, Sine, and Classical Shock as well as FFT Analysis. SignalCalc 350 is composed of modular hardware that fits inside a computer ...more

The Trig-Tek Model 2001A Vibration Controller is designed to provide either sine (S), random (R), or reference calibration (C) control as excitation for electrodynamic and hydraulic shaker systems. The system has up to 4-channels to monitor up to four sensors simultaneously. The control in the sine mode can be broken into 28 frequency ...more

The endusers appreciate the intuitive operation, the extensive analysis and reporting functions, the numerous upgrade possibilities and, of course, the excellent stability and high quality level of the systems. In co-operation with renowned partners, m+p international provides complete vibration test systems including shake and combined climatic ...more

SignalStar Matrix unites the all new ABACUS DSPcentric hardware platform with the highly acclaimed Data Physics vibration control software to produce a complete and fully integrated solution redefining the boundaries of vibration testing. ...more

The CV111 calibrator for vibration is a user-friendly precision instrument that allows you to verify vibrometers quickly and efficiently. The CV111 calibrator for vibration generates a mechanical vibration at a quartz-precision frequency and a very stable signal level. A reference accelerometer inside the shaker head and a control circuit keep ...more

The Trig-Tek, Inc. Model 523A Mixer/Monitor is a line amplifier that permits mixing of up to three individual signal sources. Each channel offers three input selections, single ended, isolated or current. The current mode accommodates voltage mode accelerometers. Each input channel can be switched in or out from the front panel and has ...more

Our VVB35 series Vacuum Base Plates bolt-down over the surface of your shaker and allow quick attachment and removal of test fixtures and our VVP35 series Vacuum Pumping Stations provide the controls to conveniently operate the Base Plate. ...more