Showing results: 76 - 90 of 292 items found.
-
MC -
Dwyer Instruments Inc.
Series MC Portable Multi-Cal Pressure Calibrator performs a wide variety of simple and complex pressure based measurement, test, and calibration operations. Modular sensor design allows user to select pressure measurement range for application flexibility.
-
CX1105A -
Keysight Technologies
The CX1105A ultra-low noise differential sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 100 A under up to 100 MHz bandwidth with existing shunt resistors on your test board.
-
Teledyne LeCroy
Teledyne LeCroy Test Services patented Quick Sensor is a pre-fabricated Torque & Thrust Strain Bridge that is applied to a shaft much the same way as a strain gage. This time-saving device was developed for the Nuclear Power Industry to reduce the time and effort required to install strain gages in a radioactive environment. Since it's introduction in Nuclear Plants, the Quick Sensor has become popular in many other industries and applications where gaging time and cost is a concern.
-
DMC, Inc.
DMC has successfully employed LabVIEW in many industries, including product development, R&D, high-tech manufacturing, and test engineering. Following are a few relevent examples: Laboratory Automation; Carbon Monoxide Detector Testing, Strobe Light Testing, Multi-Station Permeability Test Stand, Hydraulic Fluid Tribology Testing. Manufacturing Automation; Engine Cold-Test Characterization, Smart Battery Pack Manufacturing Test, Automotive Sensor Testing.
-
TOPTEST GmbH
Development of a 12-way test and programming adapter from Toptest for ?? The Dash ?? from Bragi, a wireless, intelligent earphone with communication and sensor technology. With the first version of the test adapter, only a purely sequential testing was possible due to the interdependencies of the tests. In version 3.0, the now autonomous tests were brought into a parallel TestStand sequence. In addition, individual sockets were prioritized in order to optimally use the hardware resources. This resulted in a time advantage of 80% compared to the initial situation.
-
pH1200 -
YSI Incorporated
Laboratory Instrument for pH and mV Tests. Perform accurate lab pH measurements with the YSI pH1200. Instrument features: auto buffer recognition, large display, sensor efficiency check, autolock mode and more for accurate lab pH testing.
-
Techimp HQ S.r.L
It can be chosen as PD sensor for Techimp PDCheck, PDScope or PDBaseII systems. It is suitable for on line or off line PD tests onrotating machines, for both spot measurements and monitoring applications. A BNC termination is available to connect the coupler through a coaxial cable.
-
FS SERIES -
EMIC Corporation
The system can test the sensor and ECU for an airbag and also reproduce the shock by assuming an automotive collision and full-scale crash. The system can be incorporated into the production line for total inspection. It can maintain the operating quality of the airbag to make a contribution to lifesaving against a traffic accident.
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
These piezoelectric accelerometers are particularly suited for small and light test objects. Of particular advantage may also be their high resonant frequencies. Due to the piezoelectric principle with its wide dynamic range both high acceleration and lowest vibration can be measured with the same sensor.
-
90407 -
HITEC Sensor Solutions Inc.
The Model 90407 Conveyor Test Stand by Sensor Developments Inc. is a device used for testing operational parameters of a conveyor motor/roller. The system operates the conveyor motor/roller and performs loading operations, while recording all of the important motor/roller parameters for later analysis.
-
LMT Lichtmesstechnik GmbH
Goniophotometers are required to measure angular resolved distributions of photometric or colorimetric quantities, either by rotating the lighting device under test or by moving the sensor around the device. Depending on the application, different geometries are used to obtain distributions in the appropriate CIE coordinate system.
-
Rasco Jaguar -
Cohu, Inc.
Jaguar is designed for high-volume production testing of ICs on a strip format or in device carrier. It is fully automotive qualified for tri-temperature test and the ideal solution for high parallel testing of small packages at short test times, but also for Power and Sensor devices. Due to the integrated vision alignment and high precision linear motors, Jaguar provides high yield and excellent OEE.
-
Hygropin humidity concrete ASTM F2170 -
PASI srl
The Hygropin moisture meter offers the perfect solution to identify and monitor moisture in concrete. Due to the small and fast sensor of the moisture meter, diagnosing moisture according to ASTM F2170-09 is quicker and easier than ever before. The relative humidity test requires placing a measuring sleeve at a specific depth. This can be done either by drilling a hole or by pre-installing cast holes in fresh concrete. This moisture meter provides the smallest available sensor on the market, minimizing damage to the surface and reducing the installation efforts immensely.
-
Oersted Meter -
Alpha Lab, Inc.
The Air Shipment Milligauss Meter has been designed so that one person alone can be the tester, and do repackaging, if necessary, without moving from the area. The remote sensor, shown on the right side, is connected through a 15-foot cable to the control box (left). This control box is placed next to both the package and the tester (person) so the tester can manually rotate the shipment. The remote sensor is placed either 15 feet or 7 feet away, depending on which test is being done.
-
TBM300 -
Telonic Berkeley, Inc.
The Model TBM300 Portable Opacity Meter consists of two basic units connected by a single cable. The sensor unit is installed end-of-line on the exhaust outlet of the vehicle under test and contains the light source (green led) and receiver (photo detector) modules.