Showing results: 226 - 240 of 549 items found.
-
SG-P11A -
Jinge Testing Machine Co.,Ltd
This machine, incorporating a steel striker adaptered to fall freely on vertical guides from a predetermined height to give the required impact energy to the toe of safety footwear for measuring the degree of the dent. In addition, the toecap should not develop any cracks on the test axis with go through the material.
-
Hilo Test
Hilo-Test manufactures power generators for surge current material and safety tests, in particular for the examination of diverting elements such as gas discharge tubes, varistors, SPDs, and components in which such protective elements are installed, according to according to the IEC / EN 61643-11. Below you will find the right solution.
-
VectorCAST/C++ -
Vector Software Inc.
An integrated software test solution that significantly reduces the time, effort, and cost associated with testing C/C++ software components necessary for validating safety- and mission-critical embedded systems.
-
LXinstruments GmbH
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
LXinstruments GmbH
Manufacturers and operators of electrical equipment are required to carry out an electrical safety test within the framework of the applicable regulations. This is to prevent accidents caused by malfunctions in electrical equipment, such as fire, explosion as well as injuries and personal damage. The tests to be carried out are specified in national (VDE/DIN) and international (EN/IEC) standards. After passing the test, the product is considered safe for the entire life cycle, provided it is left in its original condition and used for its intended purpose.
-
EV-TEST100 -
HT Italia Srl
EV-TEST100 in combination with appropriate HT multifunction instrument simulates an electric vehicle connected to the charging station, allowing you to verify the EVSE full functionality and electrical safety. EV-TEST100 is able to test charging stations with charging modes 2 and 3 and Type 2 connector (European standard).
-
Premier Electrosystems
Premier's Glow wire testing is an electrical safety test designed to evaluate the flame resistant properties of plastic materials used in electrical devices. Its purpose is to protect against the risk of fire from overheated or electrically energised parts which may cause the plastic material to ignite.
-
Global Testing Services Inc.
You create a custom test plan (a file that lists a series of tests to be run), to meet requirements specific to your environment and apply that test plan to any number of clusters. You specify the order in which tests run and the specific components to be tested. After you set up your custom test environment, you run the test procedure from SMIT and view test results in SMIT and in the Cluster Test Tool log file. For information about customized testing, see Setting up custom cluster testing.*Fixture Design*Fixture Fabrication*Custom Test Stands*Prototype Testing Services*Product Safety Testing Services
-
TOS9300 Series -
Kikusui Electronics Corp.
The TOS9300 series is a high performance electrical safety analyzer that complies to a wide range of universal standards. Hipot, Insulation Resistance, Ground Bond, Leakage Current (touch current and protective conductor current) and partial discharge can all be tested. A total of 6 models are available for standard compliance tests in a wide variety of applications including R&D, quality assurance manufacturing lines and laboratory tests.
-
Educated Design & Development, Inc.
Plastics are tested to determine their flammability burning characteristics (Flame rating), their ignition potential due to thermal and electrical sources, their resistance to electrical tracking, and other electrical characteristics. The specific test required on a plastic depends on the type of component or end-use product, as well as the environment in which the plastic is used. This test equipment meets most UL, CSA, IEC, EN and other international safety standards.
-
MI 3100 SE EurotestEASI -
Metrel d.d.
MI 3100 SE EurotestEASI is a fast, accurate and easy to use multifunctional measuring instrument which performs a complete set of installation safety tests according to IEC/EN 61557. Besides, the MI 3100 SE EurotestEASI enables on-line voltage monitoring, phase sequence testing and earth resistance measurement. EurotestEASI is equipped with integrated characteristics of fuses and RCDs for PASS / FAIL evaluation of test results.
-
MI 3125 BT EurotestCOMBO -
Metrel d.d.
The MI 3125BT EurotestCOMBO performs all the necessary tests for installation safety testing on TT and TN systems. The large graphic display with backlight offers easy reading of results, indications, measurement parameters and messages. Two LED Pass/Fail indicators are placed on both sides of the LCD. MI 3125BT EurotestCOMBO contains integrated characteristics of fuses and RCDs (including B type) for the evaluation of test results.
-
B-1001 -
ROSS ENGINEERING CORPORATION
Air insulated types for isolating loads, tap selections, safety discharge & grounding to help meet OSHA and other safety regulations. Ratings from 1mA to 800 amps continuous, to 100,000 amps capacitor discharge. Peak 1 minute test voltages from 5kV to 300kV. Single or Multipole. Auxiliary contacts are optional on all types. Options include latching, extended life, and tungsten contacts available for high current closing. DC, 25-800Hz & air pressure actuation available. Also usable in oil or insulating gas with increased ratings.
-
KD-500 -
King Design Industrial Co., Ltd.
*To evaluate impact effects of shock, drop and tumble encountered in repair and handling process, so do the safety strength assessment. *The general drop test is against bottom, angle, edge and tumble. According to related specifications you can lift one side of the product by angle to make it drop freely.
-
Tenney Environmental
Whether your company serves the automotive, computer, telecommunications, defense, or alternative-energy industries, you need a safe, reliable way to test batteries. The Tenney SafeTest™ system offers a comprehensive line of standard and optional test-chamber safety features that can be customized to fit your company’s battery-testing needs.