Relay Test

The 40-569 PXI Matrix BRIC provides a range of high density bus matrix inputs and resource distributor bussed configurations capable of switching up to 2A and up to 250V AC/220V DC. The 40-569 BRIC modules are available in 4 or 8 slot PXI sizes and are constructed using high quality electromechanical relays. Typical applications include signal ...more

Ideal for checking continuity of non-energized comonents, fuses, switches, relays, wiring and circuit boards. Features 30" (76cm) Test lead with alligator clip  ...more

The Power Rack comprises an optimised mix of QM special test equipment and off-the-shelf equipment. A main component is the High Current Relay Multiplexer. QM developed the High Current Relay Multiplexer for use on the Joint Strike Fighter (JSF) project but it is also applicable to other projects.  ...more

Comprehensive 4-wire DDS Local Loop test set.Monitor and test 56k, Switched-56k and 64k Primary and Secondary DDS services. Quick 56k Frame-Relay turn-up. Real-time Invalid BPV Receive Monitor. Received Signal Level measurement with 1dBm accuracy. Standard TERM mode and unique THRU mode provides real-time non-Intrusive monitor of NW or CPE. CS ...more

The Inverter Test Panel is a resistor load bank with input and output metering. Input voltage (0-30 DC) and input current (0-100 Amp) are metered on the panel. The DC input power is protected by a 50 Amp circuit breaker. The power is connected to the inverter through a 3 pin connector and controlled by the panel ON/OFF switch which operates a high ...more

The HVcompact is a high voltage meter with an auto-ranging oscilloscope display of the voltage waveform. The unit displays Û, Û/Ö2, Urms, frequency, and the crest factor. To improve the readability, one selected measurement is displayed using larger characters. To protect test specimens, the unit offers a pre-settable voltage limit, which trips ...more

YP-30H High voltage cable & harness tester (up to 1500 V). High voltage testing up to 1500 V. Conduct tests while controlling switches, relays, LEDs and other embedded equipment. In addition to all the functions of the YP-1024 low-voltage tester, the YP-30H HiPot Wired Assemblies Tester performs high voltage testing of up to 1500 V. Testing include ...more

The 30-728 is a dual 8 x 9 RF Matrix Module for switching frequencies to beyond 100MHz. Built-in relay self-test gives maximum switching confidence with early failure warning ...more

Net-O2 ATTEST STP test cases perform conformance testing for various scenarios of active topology and STP port role types. Port state tests verify for transitions from Blocking to Forwarding states and vice-versa. Data Forwarding and Filtering Database test cases verify for Relay and Filtering behavior. ...more

If you're concerned about relay quality and performance, you know how vital relevant test data is to the quality control loop. Product quality depends on the prompt response to a problem identified by test data. Whether you manufacture relays or are an end-user, quality is of prime importance to the reliability of your product. ...more

Net-O2 ATTEST RSTP test cases perform conformance testing for various scenarios of active topology and RSTP port role types. Port state tests verify for slow and rapid transitions from Discarding to Forwarding states. Data Forwarding and Filtering Database test cases verify for Relay and Filtering behavior. ...more

Our Automatic Test Equipment Division designs and assembles test equipment --hardware and  software-- for all types of  manufacturing. We have produced relay testers, semiconductor testers, CV systems, resistivity systems, military relay testers and leakage systems.Some important projects have been developed for corporations like Saturn Corpora ...more

The Model 8025, Run-In/Miss Test System from Circuit Equipment Corporation is a versatile unit, which automates the inspection and characterization of relays. The system, controlled by an internal PC and menu-driven software, tests to the requirements of MIL-PRF-83536A and MIL-PRF-39016. It tests the complete Run-in Screening (miss), pull-in a ...more

Selection of Handler Interface includes HB-100 providing relay closures or logic level (positive logic) with software programmable End Of Test (EOT) and PI-200 providing positive or negative logic with hardware adjustable End Of Test (EOT) and bin pulse widths. ...more

Test relays, motors, lights and more! Includes: 8' coiled probes with cigarette plug to provide easy access to power and ground and two (2) screw-on alligator clips. ...more

Available with two types of internal drive electronics (Binary Decoding or MOSFET Pulse Latching), these SP3T and SP4T IN-LINE Series Multithrow Switches are ideal for test equipment and simple switch matrix applications. Featuring excellent insertion loss and isolation performance through 18 GHz, along with the DowKey INTELLIGENT RELAY intern ...more

The 40-195 is a 22 Channel Fault Insertion Switch, primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. It is designed to be able to insert different fault conditions on pairs of signals between the test fixture and the equipment un ...more

The Model 8030 Chatter Test System from Circuit Equipment Corporation is a versatile unit, which automates the inspection and characterization of relays. The system, controlled by an internal PC and menu-driven software, tests to the requirements of MIL-PRF-83536 and MIL-PRF-39016. It tests the complete Vibration, Shock and Acceleration speci ...more

The DVS3 mk2 is the new smaller, lighter, higher power phase voltage source than the T&R DVS3, offering more than twice the output power of the original DVS3. The exceptionally easy to understand user interface of the DVS3 is retained, allowing simple testing of complex voltage and loss of mains protection systems. ...more

A control system operates valves, relays, and electrical components to bring a system to desired operating condition. Control systems can be configured to bring a complex system to set point based on user input or can be used to automatically operate a system over its entire range. Control systems are often used to control complex machinery acc ...more

The ETS packages includes the executable files of ETS and the templates of Clarinet file for a quick operation (Profiles, filters, Testcases list, PICS/PIXIT). These ETS result from compilation of the ATS (Abstract Test Suites) source included in ATS in TTCN-MP (IS-format) by the CLARINET-TTCN compiler.  ...more

It can be hard to confirm or identify faulty relays on complex switching matrices or multiplexers. The user may be aware that the test system is not behaving as expected but may be unsure if it is a cabling fault, a software problem or a faulty matrix or multiplexer. ...more

These high-density basic switch modules are designed for general purpose switching where individual relays can be used to route signals to/from the units under test (UUT), or combined externally to form user-defined configurations. ...more

Available with either 15 Vdc or 28 Vdc actuator coils, these DowKey INTELLIGENT RELAY IN-LINE Series SP12T Multithrow Switches are available with internal binary decoding CMOS logic circuits with latching self cut-off drivers. The IN-LINE construction has the common port in the center of the RF cavity to provide excellent electrical performanc ...more

Available with either CMOS Binary logic decoding circuits or MOSFET pulse latching electronics, these DowKey INTELLIGENT RELAY Multithrow Switches were designed to simplify the physical construction and reduce the amount of supporting (logic and switch driver) electronics required to implement complex switch assemblies. These SP7T and SP10T Do ...more