Programmable Voltage Sources

The 236, 237, and 238 Source-Measure Units (SMU) are fully programmable instruments, capable of sourcing and measuring voltage or current simultaneously. These systems are really four instruments in one: voltage source, current source, voltage measure, and current measure. ...more

The R&S NGPS32 is a programmable voltage source with two isolated identical outputs. The bipolar output voltages (... 32 V to +32 V) can be set with high resolution either manually or via the IEEE488 interface. Two integrated simple arbitrary generators allow independent output of low-frequency waveforms. The R&S NGPS32 is suitable for ...more

NGPU Power Supplies are constant voltage or constant-current sources, which can be programmed via IEC/ IEEE bus or operated manually. Three selectable current ranges and one floating test output which can be switched between voltage and current make the NGPU ideal for use in IEC/ IEEE-bus test systems. ...more

The DCX-127 Multifunction Module provides Audio Precision's PC-controlled audio analyzers with an interface toolkit of non-audio functions and interface capabilities that are often required in typical audio test applications. The module contains a 4-1/2 digit DC voltmeter-ohmmeter, two 20-bit programmable DC voltage sources, 21 bits of digital ...more

Programmable Pulse Generator - Augments the capabilities of any programmable voltage source to provide narrow pulses. In conjunction with a VF or VFIF module, the PPG can provide voltage pulses up to 30V. Single or multiple pulses can be generated. ...more

Power Supply Module - programmable voltage/current source which can supply a load current of ±200mA at voltages of ±100VDC. Analog circuitry consisting of two precision DACs, error amplifier, precision voltage clamp, voltage controlled current source (VCCS), power output stage, sense buffer amplifier, and precision feedback components. Voltage ...more

The EC1000S not only supplies AC and DC power as the ordinary power supply, it also allows free programming of outputs such as instantaneous interruption, voltage sweep, and voltage variation patterns. The EC1000S also has essential functions for power tests, including a variety of output measurements and measurements related to the load power ...more

Dual-Channel Analyzer/Power Supply. The Dual-Channel Analyzer/Power Supply NGMO2 from Rohde & Schwarz is more than just a simple power supply for test and measurement applications. This is shown by its advanced features: accurate high-speed voltage source, programmable DC load, precise digital voltmeter, storage oscilloscope, simple square ...more

DC DC Module single output with the power of 40 watts. Input voltage of 1.8 to 13 V. Programmable Output from 0.9V to 3.6V. -40°C to +85°C Ambient Operating Temperature. External Trim Resistor or Voltage Source). ...more

Advanced Conversion Products offers programmable DC power sources for a variety of industrial and laboratory applications including oil field wireline power and telemetry. Both standard and customized units are available to suit customers needs. Our DCP Series of DC sources feature very low noise. The wireline used to conduct DC power to the down- ...more

The GX1838 is a multi-channel programmable DC Source providing test engineers in avionics testing and other ATE applications with multiple discrete outputs. The GX1838 provides 8 output channels and three Voltage Rails. Each of the 8 output channels can be connected to one of the three voltage rails or set as Open. ...more

Power Supply Module - A programmable voltage source which can supply a load current of greater than 200mA at output voltages of ±100VDC with respect to ground. Analog circuitry consisting of a high gain, high voltage, FET input operational amplifier followed by a power output stage. Voltage reference for the VF is a 12-bit precision DAC. ...more

64 bit Hot Swap 66 MHz, PCI/PCI-X extender card, 3.3V keyed top connector* 3.3V5V Signal Level Conversion Software programmable via parallel port to:  ...more

Programmable Triple Power Supply. Insensitive to RF voltages radiated by device under test or nearby antenna. Simultaneous readout of nominal and actual values of all channels. Coupled protection mode for DUTs which should not be supplied from an asymmetrical voltage source. Software calibration via IEC/IEEE bus without potentiometer adjustmen ...more

The ContinuousWave (CW) Series of AC power sources provides clean single phase power at an impressive price/performance ratio. These compact switch mode sources come in two series, manual (CW-M) or programmable (CW-P) with standard IEEE-488.2 and RS 232 control. Both the manual and programmable models can be field configured for three phase op ...more

32 bit Hot Swap 66 MHz, PCI/PCI-X extender card, 3.3V keyed top connector* 5V<=> 3.3V Signal Level Conversion Software programmable via parallel port to:  ...more

The VT1518A 4-wire Resistance Measurement SCP provides four programmable current source channels (with input over-voltage protection) for excitation. Each current source can be programmed to provide either 30 mA or 433 mA. ...more

The VX2600 High Precision DC-Source is designed to generate precise and low noise reference voltages of high stability. The output voltage of each channel is programmable. The VX2600 is available with 4, 8 or 12 output channels. Each group of 4 uses the same common ground which is floating against PE ...more

Wide Test Current Range: User programmable output current, 3A to 45A AC in 0.01A steps, provides extensive coverage for testing to UL, CSA, VDE, IEC and other agency safety requirements. Programmable Source Voltage: Limit the voltage to the DUT using the programmable source voltage from 1.0V to 8.0V rms and meet the low voltage requirement of ...more

The Kepco Model BOP 500M and BOP 1000M are high voltage power sources, up to 500V or 1000V, respectively. These combine the capabilities of fast programmable power supplies with a Class A output stage, which can respond bidirectionally from zero. ...more

AC or DC high voltage dielectric breakdown testing of cables. Models available with AC & DC breakdown testing in the same unit. Programmable high current source from 1mA to 1A. Very accurate measurements of components in cable assemblies. 2-Wire & 4-Wire Resistance Measurement ...more

Characteristics of SFB 1050. Voltage source with adjustable current limitation. Current source with adjustable Voltage limitation. Programmable capacitors Cf, Cs and feeding coils. External feeding mode. External adaptation of L, Rf and C  ...more

Programmable voltage -500 to +1500V, output current ±50mA in pulse mode, ±10mA in continous mode , 5 current ranges from ±10uA to ±50mA, rise time from 10V/ms to 1000V/ms, Voltage measurement range 1V to10000V, current measurement range from 100nA to 100mA, voltage monitor, current monitor ...more

These Power Managers are high voltage 20-, 25-, and 35-Watt fast programmable power supplies, which can stabilize a voltage or current against the effects of load, source, or temperature changes, yet respond with agility to programming signals requiring s ...more

With the combined voltage and current source in a single compact chassis, the FX Series is the ideal choice for the simulation of high power levels. Either single or multi-phase, this versatile source can simulate power levels from just a few milliwatts to 54kW single phase or 162 kW three-phase and provides a universal system for both manual and p ...more