Power Sensors

When used with the N192XA wideband power sensors, the N1912A P-Series dual channel power meter provides a measurement frequency range from 50 MHz to 40 GHz with an internal zero and calibration capability.  ...more

The Agilent P-Series wideband power sensors are designed for use with the P-Series power meters. The N192XA sensors are the first to provide internal zero and calibration, by integrating a DC reference source and switching circuits into the power sensor. ...more

Excellent SWR for reducing mismatch uncertainty. Accurate average power measurements over -10 to +35 dBm. Accurate calibration and traceability to US National Institute of Standards and Technology (NIST)  ...more

13U High Shelf is available in 19" 14-Slot or 23" 16-Slot. Four RiCool-2 Blowers provided 200 Watts/Slot of cooling. Shelf Manager interfaces throughout the Shelf enabling the monitoring of: Power Entry Module, air inlet temperature, remote alarm signals, air filter present sensor, boards and blowers ...more

RLB-L is used to measure and display heat power in pipes. It is separate structure and convenient for outdoor use. It consists of controller, flow sensor, microprocessor, temperature sensors and flow main meter. Connection line between flow main meter and controller is 3-meter long, which guarantees convenience for swiping IC card by consumer e ...more

The E1416A is a single channel VXI power meter with features and capabilities based on the 437B power meter (now discontinued), and is compatible with all the 8480 series sensors.  ...more

RLB can measure and display heat power in pipes. One household with one meter and one IC card for consumer. It consists of flow sensor, microprocessor and temperature sensors. Microprocessor obtains flow signals through flow sensor and signals of water temperature at the entrance or exit by temperature measuring circuit, and then it will calcul ...more

A touch panel and function keys make this device comfortable and easy to handle. The preamplifiers integrated into the device and the choice of sensor sensitivity allow a wide range of sensor heads to be used. The large graphic display offers space for a variety of display and analysis choices. The digital display can be used for determining th ...more

DRV offers reconfigurable visible and IR sensors that fully exploit limited video processing and communications bandwidth in tactical applications. DRV’s EO/IR sensors offer: maximum situational awareness for unmanned vehicles, unattended sensors, and other wireless systems; better resolution and field-of-view than traditional sensors ov ...more

Excellent SWR for reducing mismatch uncertainty. Accurate calibration and traceability to US National Institute of Standards and Technology (NIST) millimeter-wave sensor calibration  ...more

Ideal for spot checking humidity levels. Measurement range 0...100 %RH. Fast response with +/-2% accuracy. Temperature measurement range -20...+60 C (-4...+140 F). Lightweight, pocket-sized. Extendable probe. Automatic POWER-OFF. Available in either F or C. NIST traceable (certificate included). Incorporatess Vaisala HUMICAP Sensor that provide ...more

The 11730A power sensor cable (grey) is used with the 8480, E-series power sensors (except the E9320 family of peak and average sensors) and the SNS series noise sources. ...more

The QRP HF sensor extends our sensor lineup to satisfy the needs of the QRP operator.   Same price as our  2KW and 8KW  -- $60.00 each. This sensor provides accurate Power and SWR measurement  between 20 milliwatts and 60 watts.  Mix and match with our other sensors to provide QRP to QRO  measurement, no compromise.   The WaveNode Sensor se ...more

PD-MCC&G400A is an on-line Partial Discharge (PD) diagnostic system, which detects and analyzes the generation of PD in the power equipments such as Cable and Motor. Four High Frequency Current Transducer (HFCT) Sensors are installed ground line in power equipments to detect PD signals. PD-MCC&G400A PD-MCC&G400A is an on-line Parti ...more

Quartz Dual Axis Rate Sensor (QDARS) incorporates solid-state quartz MEMS inertial rate sensors. It is especially suited for missile seeker gimbal stabilization where extremely small size, low cost and low power consumption is required. ...more

The E4417A dual channel EPM-P series power meter, is designed for peak, average, peak-to-average ratio and time-gated measurements, using the E9320 peak and average power sensors.  ...more

The Cabletroll 2700 is a complete system for indication of earth-fault and short circuit faults in an underground 6-36 kV cable network. The system consist of three different modules: An Earth Fault Element with a split core for sensing the imbalance during earth faults. 2 (or 3) Short-Circuit sensors for detecting short-circuits. Processing un ...more

The V180 is a single-width VME module that allows accurate and comprehensive measurement of AC power circuits. The V180 acquires powerline current and voltage inputs using approved current transformers and model C750 remote potential transducers. Up to sixteen CT sensors and eight potential connections (six lines plus two neutrals) can be acco ...more

The Agilent 11708A 30 dB attenuator is supplied with 8480 series power sensors with the "D" suffix, for calibration with the power meter 0 dBm, 50 MHz reference.  ...more

The Multifunction Calibrator Model 8080 functions as a Voltage Calibrator, Current Calibrator, Power Calibrator, Resistance Calibrator, Capacitance Calibrator and a Thermocouple Calibrator. Having very low uncertainties, the Multifunction Calibrator is ideal as a standard of these electric quantities in calibration laboratories. The Multifunction ...more

The System 200 is an expanded feature model of the HyperLogger portable data logging system. The System 200 consists of a HyperLogger and an RPS-1 Rechargeable Power Supply housed in a NEMA 4x rated enclosure. The System 200 was designed to meet the needs of remote data logging applications where power is unavailable for excitation of sensors an ...more

This OEM-Meter is assembled in a standard cassette for the industrial 19? system. It has a width of 21TE. A touch panel and function keys make this device comfortable and easy to handle. The preamplifiers integrated into the device and the choice of sensor sensitivity, allow to use a wide range of sensor heads.  ...more

Flat sensitivity characteristics at the 400 nm wavelength. h power measurement (100 mW). The influence of multiplex reflection is eased by the sensor's low-reflection surface. ...more

Detects ALL halogenated refrigerants. Detect once power on, no need manual-adjustment. Van-speed sensitivity adjustment. Enter into the best state of detecting automatically while adjusting the sensitivity. Tricolor battery voltage indication. Equipped with quality sensor, high sensitivity, 6gr/yr. Inner precise IC with ultra-low consume circu ...more

SIR-1000i Sensor(ICPtype) input capability in addition to all the same features of the SIR-1000 The SIR-1000i has built-in ICP power supply, which enables direct connection with ICP® sensors. This function saves space at a recording site, making the SIR-1000i a perfect fit in field recording applications. Input mode is switchable between senso ...more