POTS

The TSP Edge gives you high-end telecom test system power in an affordable and scalable package. Offering T1, E1, PRI (North America and Euro protocol) and POTS simulation, extensive programmability, scripting, and more, the TSP Edge is ideal for feature and performance testing applications in R&D, QA, production, demo and training environments. ...more

Teltone's TLS-3B 2-line simulator makes it easy to test or demonstrate equipment that connects to the North American telephone network (POTS), without requiring a live central office connection. Features: Two line Central Office/PBX simulator with one talk path. Supports single and multiple message format Caller ID plus Visual Message Waiting. ...more

A next generation field test set for subscriber loop fault identification and location and voice and data line qualification. Replaces up to sixteen traditional test sets. Troubleshoots and qualifies lines for POTS, ADSL and other special services. Time Domain Reflectometer (TDR) feature allows precision fault location. ...more

P-Phone Adapters enable analog telephone test sets to be used on POTS or Meridian Digital Centrex lines with the use of a simple slide switch. ...more

MULTI-SERVICE TIMS (Transmission Impairment Measuring Set). The 806A supports a wide range of services including: POTS, DATA, Program, DDS, DSL (ISDN basic rate), and T1 via HDSL. It measures: LEVEL, DELAY, FREQUENCY, NOISE, NOISE with TONE, S/N RATIO, NOISE to GROUND, IMPULSE NOISE, IMPULSE NOISE with TONE, and IMPULSE NOISE to GROUND per IEEE ...more

P-Phone Adapters enable analog telephone test sets to be used on POTS or Meridian Digital Centrex lines with the use of a simple slide switch. ...more

This tester is designed for testing equipment wiht a line cord which can be plugged directly to the tester. The continuity test is to determine whether the ground wire of the line-cord is well connected to the metal frame of the unit under test. ...more

The EE30140A DC Electronic Load /  Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices ...more

The ARGUS3u NT is the all-round tester for BRI, U-interface and POTS accesses. On a BRI, the ARGUS3u NT offers passive monitoring and simulation of the exchange and support for testing permanent circuits. Additionally, this tester offers convenient testing of cables and can recharge the accumulators in the tester. The ARGUS series’ all-round ISDN ...more

RT-2X is a fast 2-channel voice frequency test system for telecommunication testing. It comprises analog and digital interfaces (POTS, ISDN, T1, E1, J1, PCM) with the capability to evaluate all important performance parameters of a telecommunication device within fractions of a second. ...more

P-Phone Adapters enable analog telephone test sets to be used on POTS or Meridian Digital Centrex lines with the use of a simple slide switch. ...more

The premium tester for all of the most common interfaces providing support for easily testing and installing E1, PRI and BRI (with optional support available for the U-interface and X.21) accesses. The ARGUS26 is the premium tester for PRI, BRI, and POTS accesses as well as for permanent circuits. On a PRI or BRI, it supports TE/NT simulation and m ...more

The EE15140A DC Electronic Load /  Works @ 0.0 Volts Input & real time I/O control  attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices ...more

The EE30181A DC Electronic Load /  Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running.  used them with D to A's, A to D's, Pots, PLC's to control the current ...more

The EE15120A DC Electronic Load /  Works @ 0.0 Volts Input & real time I/O control attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices. The electronic ...more

The EE30141A DC Electronic Load /  Works @ 0.0 Volts Input & real time I/O control. attach the electronic load block to a heat- sink and your up and running. used them with D to A's, A to D's, Pots, PLC's to control the current. These Electronic Loads can be used for both Discharge & Charging Batteries & Devices ...more

Talk-listen support for the IEEE 488.2 bus using SCPI is afforded by two plug-in cards: BIT 4882 and BIT 4882-F are 12-bit with resolution of 1/212; BIT 4886 is 16-bit with resolution of 1/216. These cards allow BOP to communicate as a stand-alone instrument, directly on the GPIB. The downloadable BIT 4886 driver supports digital calibration ( ...more

The WBK16 provides eight channels of strain gage input for the WaveBook. 100% programmable; no pots to adjust. Optional simultaneous sample and hold. Independent filter per channel ...more

Tollgrade?s DigiTest MSAS provides metallic test access when no other means are available. For ADSL line-shared applications, an optional POTS splitter can be added for test access or to be used solely as a splitter shelf. The MSAS resides within the network?between the subscriber lines and access elements?enabling service providers to non-int ...more

Tester that will substantially ease the day-to-day work of service technicians and engineers in the commissioning, maintenance and networking of PBXs. It has test routines for both E1/2Mbit and PRI accesses and, on PRI accesses, also supports monitoring of the D-channel. In addition, it has all of the functions required for the installation and ser ...more

Auto-Test / Auto-Setup, used for services spanning POTS to HDSL, provides a consistent method for facilities testing which relieves the operator of tedious details. The send end operator selects one of three measurement bandwidths and presses START - that's it! ...more

The 965DSP analyzer is a microprocessor-controlled integrated test set that provides fullfeatured POTS, wideband and DSL-specific testing. The functions include fault location and repair verification on twisted-pair and drop cables (utilizing capacitance bridge, resistance bridge and Time Domain Reflectometer (TDR) functions). ...more

The practical tester for BRI, U-interface and POTS accesses and permanent circuits. The right decision in a handy entry-level tester. Functional with an intuitive design for day-to-day use on ISDN accesses. Additionally, this tester offers convenient testing of cables and charging of the accumulators. Integrated handset in an ergonomic design. ...more

The 950ADSL qualification test set can provide a low-cost solution for POTS testing and verification of ADSL modem connectivity at customer locations. The Dynatel test sets are housed in a light-weight, hand-held case designed for ease-of-handling and portability. Each unit weighs less than 2.5 pounds with the rechargeable battery pack include ...more

The ARGUS 145 offers an exceptionally broad spectrum of measurement functions and supports tests on SHDSL, ADSL, ADSL2 and ADSL2+ as well as POTS, U-interface and BRI accesses. The ARGUS 145 is also well equipped for checking Internet connections with IP-PING and Trace Route functions as well as download tests. In addition, the tester offers an Eth ...more