The EPM 2000 meter measures more than 40 electrical power parameters providing a low-cost, multifunction monitoring solution for industrial and power generation applications. EPM 2000 can easily be mounted in a panel for generator monitoring, substation automation and more. Meter can also provide data to RTUs, PLCs and other control devices.
The EPM 2200 meter measures more than 40 electrical power parameters providing a low-cost, multifunction monitoring solution for industrial and power generation applications. EPM 2200 can easily be mounted in a panel for generator monitoring, substation automation and more. The meter can also provide data to RTUs, PLCs and other control devices.
Automatic reading meter system is system to remotely read, store, transmit and monitor power consumption of energy/KWh meters in power network, which adopts power line carrier (PLC) technology (the system is also named PLC system). Because the existing power line is regarded as communication medium, the system features easy installation and low cost and high stability.
PLC (Power Line Communications) is a well known technology. In the last couple of years, a variety of PLC based applications and large projects were introduced. This includes AMR (Automated Meter Reading), Command & Control, intelligent infrastructure, and more.
Achieved by remote monitoring system. Over 90 Power and energy parameters. For Factory and Building Automation. PLC ModBus compatible. 5 A / 1 A Auto-Range. Max. 600V auto-range 10~150V/600V. True RMS conversion. Instant Maximum & Minimum
Achilles Test Software tests the robustness of any IP-enabled network component, whether a complicated distributed control system (DCS) or a simple SCADA PLC, sophisticated AMI or an end-point smart meter, over wireless or a traditional copper.
The GM81002, GM81003, GM81005 and GM81006 Optical Power Meter modules offer superior performance in testing DWDM components, AWG & PLC components, optical amplifiers, and performing other general-purpose fiber optical test and measurement applications.
DTSY23S Three-phase Keypad Prepayment Electronic Energy Meter complies with STS certification and IEC international standards, it supports DLMS communication protocol. The meter is equipped with pluggable GPRS , PLC communication module, will do the settlement with kWh or amount. The meter has two price programs of TOU price and step price, supporting remote meter reading, is switchable between prepaid and post-paid modes.
This converter was designed for a specific purpose. It requires 9 to 24 volts to operate and only converts one way. It's intention was to act as an interface between a flow meter with a digital TTL Async streaming output and a PLC with a RS422 input.
Measure 4-20 mA signals without breaking the loop with this new, compact clamp meter for PLC and control systems analog I/O. The detachable clamp with extension cable allows you to take measurements in tight locations, and the built-in spot light illuminates hard to see wires in dark enclosures.
A three phase load bank rated for 48kW, with fan cooling. The front panel layout includes a switch panel for configuring the separate resistor modules to give the required resistance and current range. There are also digital panel meters for displaying the phase voltages and currents. An interface for PLC control is also provided.
The GM8012 + 2 X GM8300X optical power meter offer superior performance in testing DWDM components, AWG & PLC components, optical amplifiers, and performing other general-purpose fiber optical test and measurement applications. This is a special design for mass production line application.
A portable handheld instrument with Selective Level Meter / Spectrum Analyzer, Generator, Distortion Meter, Return Loss, Balance, DMM and TDR. Small, lightweight package with 75 / 125 / 600 or 75 / 150 / 600 Ohms, 2 MHz BW for RF, PLC (Power Line Carrier), PCM analog interfaces, Telephone and Voice Copper Line testing .
OPTICAL MULITIPORT POWER METERS are PC control multiport passive components power meter test systems and offer superior performance in testing multi-channel DWDM, WSS, ROADM, AWG & PLC components and modules, optical amplifiers, DWDM system and performing other general-purpose multiport fiber optical test and measurement applications. The meters can be integrated with tunable laser source, optical attenuator & PDL controller to provide a high performance passive components and modules automatic ...
CRY2112/2110 Noise Transducer/Noise Sensor is a new-type sound level meter which is applicable for remote noise monitoring and meets GB/T3785 Type 1 and Type 2 standards, it can output sound pressure level data on display screen of traditional sound level meter directly with 4-20 mA current signal, 1-5V voltage signal or RS485 digital signal, Transmission distance is greater than 1Km; it is easy to connect various controling equipments such as PLC, PC and DCS.
A portable handheld instrument with Selective Level Meter / Spectrum Analyser, Generator, Distortion Meter, Return Loss, Balance, DMM and TDR. Small lightweight package with 600 / TN12 impedances for VF (200 Hz to 4 KHz) testing of the PSTN, analog FXS and FXO interfaces of digital exchanges and PCM multiplexers. Plus 75 ohms for RF (2 kHz-2.2 MHz) testing of Power Line Carrier (PLC) .
A new generation sound level meters from Pulsar Instruments plc to suit every application & budget• Compliant with IEC 61672-1:2002• Intuitive design• High performance• Simple to use• Designed and manufactured in the UK• Rugged diecast metal case• Large anti-glare display. LEMO pre-amp microphone connectors• High definition colour OLED display• Greater than 30 hour battery life• 4GB removable memory card• Dynamic range of 20dB(A) to140dB(A) & 143dB(C)• Simultaneous measurement of all key paramet...