CIC301 - MIL-STD-1553 - Simulator / Analyzer / Tester PCI BUS Interface Card The CIC301 is a full-featured, high performance, Dual Redundant MIL-STD-1553 A/B serial bus Simulator Analyzer Tester designed as a plug in card for PCI backplane. The CIC301 includes full error injection and can operate in indepen­dent or simultaneous mode as a Bus Controller, multiple simulated Remote Terminals and full/sele­ctive Monitor. Its data structure can be changed on the fly without interrupting the processor for real time operation. The active monitor stores, time tag and annotates bus traffic with the message type and any detected errors. Stored words are annotated with a break down of the word error.

ST-PTI9 - PCI pc motherboard diagnostic post debug test card with external LCD display It can diagnosis the motherboard signal which show the problem of CPU, Memory, display card and so on. Intelligent analysis of the code corresponding to the cause of the malfunction, and gives diagnostic program! It can display the halting execution automatic with a couple of times

pcibus1b - PCI bus test adapter All important PCI bus signals routed to pin headers for easy connection of logic analyzer. Filter assistance for logic analyzer: D-FF to delay FRAME# by one cycle. To see actual PCI data transfers, filter for FRAME2# high + FRAME# low (address phase), or IRDY# low and TRDY# low (data phase). Business card size. Notched for 5V PCI bus (can be used on 3.3V bus with mechanical modification).

PCI Compliance Testing The Payment Card Industry Data Security Standard (PCI Standard) defines merchant requirements for securing cardholder information. This worldwide standard for consumer data protection across the payment industry was developed to counteract the rising number of incidents of stolen cardholder account data.?

PCI & ISA Diagnostic Test Card VER 3.2 Advanced 4-Bit 4-Digit Diagnostic Card / PC Analyzer. Diagnostic Card is a powerful diagnostic tool for technicians and administrat ors to troubleshoot various problems of IBM compatible PCs. It is easy to install, yet extremely powerful to use. With Diagnostic Card in hand, you no longer have to go through tedious and time consuming process of trying to figure out what is wrong with your PC hardware. Diagnostic Card will tell you exactly what is wrong with your PC in just seconds.

PCIPOST - PCI Post Diagnostics Test Card The StarTech.com PCI Post Diagnostics Card makes troubleshooting PC problems easy. Simply plug the card into a PCI slot on a malfunctioning PC, and the card reports any problems in the form of error codes on it's LED display.

ST8678 - PCI pc motherboard diagnostic post debug test card with LCD display It can diagnosis the motherboard signal which show the problem of CPU, Memory, display card and so on. Intelligent analysis of the code corresponding to the cause of the malfunction, and gives diagnostic program! It can display the halting execution automatic with a couple of times.

ULTRA T1 (E1) - PCI Based Ultra T1/E1 Cards - T1/E1 Analyzer The ULTRA T1 (E1) is an enhanced third-generation product that consolidates the essential pieces of industry-standard test equipment into a powerful, PC-Based T1 and E1 solution. Utilizing familiar computer user interfaces, it provides comprehensive and versatile T1 or E1 testing capability at a competitive price.

Ultra OC-3 / STM-1 - OC-3/STM-1 Ultra Card The Ultra OC-3/STM-1 card (PCI) plugs into a PC expansion slot for analyzing, testing, simulating, and monitoring OC-3 and STS-1 signals. The Ultra OC-3/STM-1 card may be used in conjunction with GL's Ultra T1 Card, Ultra E1 Card and Ultra T3 Card in the same PC to provide a complete OC-3/STM-1, STS-1/STM-0, DS3, DS1, E1 and DS0 testing solution.

Universal HD T1/E1 - PCI Based Universal T1/E1 Card The Universal HD T1/E1 is an enhanced PC-Based T1 and E1 solution that utilizes familiar computer user interfaces, to provide comprehensive and versatile T1 or E1 testing capability at a competitive price.

UltraT3 Cards - PCI Based Ultra T3 Analyzer The GL's UltraT3 Cards (PCI) plug into PC expansion slots and provide digital T3 input/output for analyzing, testing, simulating, and monitoring T3 signals. A single T1/E1 input and output is provided to insert and receive T1 (or E1) signals into the T3 stream. The cards provide the capability of generating 28 DS1 or (21 E1) signals within the DS3 output. The T3 Card when used in conjunction with Ultra T1 Card in same PC provides a complete DS3, DS1, and DS0 testing solutions.

50-296-021-1/24 - PCI Programmable Potentiometer Card Programmable Potentiometer module with up to 9-channels of 8-bit resolution potentiometers in a single PCI card. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.

50-725-751 - PCI 8x9 RF Matrix 500MHz 75 Ohm mini SMB 8 x 9 RF Matrix Module suitable for switching frequencies to beyond 500MHz. The 50-725 is available in either 50 Ohm or 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximizes isolation and RF performance.

41-921-001 - PCI to PXI Remote Control Interface A seamless connection between a control PC's PCI interface and a PXI chassis. The 51-921 resides in one of the controllers PCI slots and provides two independent StarFabric serial interfaces, each capable of driving a separate PXI chassis. The 41-921 resides in the Slot 1 position of a 3U PXI chassis and interfaces to the backplane of the PXI chassis. When located in a generic peripheral slot the 41-921 can be used to drive two extension PXI chassis.The use of the StarFabric interface operating at 2.5 Gb/s minimizes the impact on system speed. The PCI interface of the 51-921 supports both 32 bit and 64 bit operation and backplane speeds of 33 MHz and 66 MHz, ensuring the highest speed operation under all conditions. The StarFabric interface ensures the modules perform seamlessly with no impact on the test system software.

basicCAR 3085 - Mini network tester The mini network tester basicCAR 3085 is a stand-alone solution for testing important test complexes, such as net management, diagnostic or data determination or node configuration via CAN and LIN. The modular solution provides up to two CAN interfaces, two serial interfaces (configurable as K-Line or LIN interface), an interface for the J1850 communication protocol, integrated clamp control (Kl.30, Kl.15) as well as disturbance functions for CAN and LIN. Transport protocols, diagnostic and various intelligent additional options (all executed on-board) are available in analogue form to the CAN bus controller PXI/PCI 3052 and basicCAN or the LIN bus controller PXI/PCI 3072 and basicLIN.

PCI301 - PCI BUS Interface Card MIL-STD-1553 A, B & McAir MULTI PROTOCOLS Simulator/Analyzer/Tester PCI BUS Interface Card - The PCI301 can be used for Validation Testing, Production Testing, full bus simulation and monitoring, as a general purpose 1553 interface or a stand alone bus Analyzer. For precise message scheduling and measurements, the Major and minor frame times are independent of message sequences or retransmissions on errors and the start of all command messages are independent of message length, response time or length of response. Message timing is calibrated and RT responses have low jitter.

PCI Gen PCI Gen is a companion card to our RST PRO2 card. With both cards installed in a target PC, the PCI Gen allows for a comprehensive system memory Bus testing. While the RST Pro2 tests for memory failures and incompatibilities, PCI Gen runs specific Bus loading and RAM testing. 

ARINC-629 Test and Simulation Products Corelis Arinc-629 PCI-based and VXI-based modules provide broad ARINC-629 bus testing capabilities, multiple terminal simulation, monitoring of ARINC-629 bus traffic, and fault insertion and detection.

VTG-3016 - Test Signal Generators for Analog Displays The VTG-3016 PCI board is an analog video generator, designed for testing, evaluating and servicing many types of CRT, analog input displays and other devices. It supplies all the necessary signals for displaying test patterns at various timing formats required by CRT and other devices with analog inputs.

VTG-3030 - Test Signal Generator for Analog Displays The VTG-3030 PCI board is an analog video generator, designed for testing, evaluating and servicing many types of CRT, analog input displays and other devices. It supplies all the necessary signals for displaying test patterns at various timing formats required by CRT and other devices with analog inputs.

4690 - Socket Saver The Technobox PMC Socket-Saver permits cost effective volume testing of PMC modules when used with Technobox P/N 3390 ?PMC to PCI adapter for Test.? It may also be used to reduce wear and tear on Technobox P/N 1518/1523 (?Extender/Preprocessor?).

Technical Security Assessment & Penetration Testing Largest testing team of its kind in the world CHECK, CREST and PCI accredited Detailed reporting of all vulnerabilities provided

PCI-Engine - Design/Development/Acceptance Testing of Engine Control Units The PCI-Engine is an innovative tool for the design, development and acceptance testing of engine control units (ECUs). PCI-Engine provides a complete electronics interface to the ECU to facilitate early prototyping, rapid prototyping, verification and validation testing, as well as end-of-line production testing.