Showing results: 1201 - 1215 of 9914 items found.
-
Pickering Interfaces Ltd.
Pickering's PXI programmable load modules offer a solution to applications requiring higher power handling capabilities, up to 15W in a single PXI slot. High Power Potentiometers can easily be formed by using two channels of Programmable Load Resistors in series, using the unconnected terminals as the A and B connections and the link between the two channels as the wiper connection.
-
34980A -
Keysight Technologies
The 34980A General Purpose switches can be used to route signals or to control other devices in an application. These switches are ideal for device actuation, switching loads or power supplies. Both switches offer high power channels up to 150W. The general purpose modules also include a relay switch counter to help predict when relays need to be replaced.
-
CPCI-SIP-rp -
ALPHI Technology Corporation
The CPCI-SIP module provides a 3U high performance flexible I/O scheme that supports industry standard Industry PacksĂ”. For application requiring low cost, high density I/O or unique combinations, the CPCI-SIP is the perfect solution.The CPCI-SIP is also available with the Industry Pack lines routed to the CompactPCI P2 connector for application that require rear panel I/O.
-
M9130 -
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai M9130 optical receiving module is designed for ONU optical fiber network unit. This series of product with perfect detect and remote shutting off function adopts high sensitivity receiving tube and Huatai special low noise matching circuit. It is a kind of high index, low power consumption and high cost performance RFTV optical receiving unit.
-
ModTest -
Rotork plc
Modtest 2 software allows the configuration and settings of a Rotork Modbus Module Mk2 inside an individual actuator to be carried out easily and simply over the data bus. In addition, the actuator can also be exercised using this PC based software. The Modtest 2 software is used for diagnostic and maintenance of a Modbus controlled actuator over a serial link from the PC.
-
41-670-101-AABBCC -
Pickering Interfaces Ltd.
The 41/43-670-101 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has four banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
41-670-103-AABBCC -
Pickering Interfaces Ltd.
The 41/43-670-103 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types. It has two banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 2 channels of 5 or 6-wire or 4 channels of 4-wire.
-
41-752A-001 -
Pickering Interfaces Ltd.
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 6-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
41-752A-003 -
Pickering Interfaces Ltd.
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
41-752A-002 -
Pickering Interfaces Ltd.
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Curtiss-Wright Defense Solutions
The 3U VPX (VITA 46 and 48.2) Flash Storage Module (FSM) provides high-performance, high-capacity, solid-state SATA storage with AES-256 bit encryption using an Application Specific Integrated Circuit (ASIC) that is FIPS-140-2 validated (Certification #1472). The 1" pitch conduction-cooled solid state storage device utilizes high reliability SLC NAND flash designed for the most demanding application.
-
DP-VME-4059 -
Data Patterns Pvt. Ltd.
DP-VME-4059 is a rugged module with 48 channel relay output, constructed using 2 Form 'C' Double Pole Double Throw (DPDT) relays. The relay channel operation is controlled through the VME bus. Internal read-back is provided to confirm the selected commands. The pole, Normally Closed (NC) and Normally Opened (NO) contacts are terminated at a pair of front panel 96-pin EURO male connectors.
-
41-670-XYZ-AABBCC -
Pickering Interfaces Ltd.
The 41/43-670 range is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. Available with up to four banks, each bank is capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
Pacific Instruments, Inc.
Series 6000 digital I/O modules record signals from frequency counters, flow meters, encoders, discrete transducers, IRIG time, etc. which are often part of the test environment. These digital signals are time aligned and recorded alongside the system’s analog measurements. High density digital inputs provide an opportunity to easily include facility controls like switches, valve positions, relays, lights, etc. along with the test data. Series 6000 digital I/O modules also provide outputs generated by user command or automatically by Sequence, Alarms or DSP. User generated outputs are accomplished in software while sequencers can be programmed prior to a test and initiated by program or hardware control. Alarm conditions preprogrammed on the analog side can automatically generate digital outputs which are typically connected to facility control systems or PLCs. A DSP adds powerful real-time processing and is appropriate for PID control loops, derived parameter calculations and a variety of other real-time operations.
-
QProny -
QWED Sp. z o.o.
In order to assist the users of QW-3D in the analysis of high Q structures, a special software module QProny, co-authored by Prof. M. Mrozowski was developed. QProny uses one of the most robust signal processing techniques known as the Generalised Pencil of Function Method (GPOF) and employs unique and innovative methods for automatic selection of the most important parameters such as:• the number of initial samples to be skipped• the number of samples required for model construction• the model order