Magnetic Field Test

The ELT-400 for measuring magnetic fields in occupational and public environments and in EMC laboratories is especially designed for use by health and safety professionals in industry and insurance. The instrument performs precise B-field measurements in the frequency range from 1 Hz to 400 kHz. The ELT-400 uses a standards-compliant 100 cm2 p ...more

AC magnetic characteristics test equipment for single sheet plate capable of testing the magnetic steel sheet itself used for electric equipment. Based on the principle of magnetic potential difference method, it compensates the magnetic field gap so that it can gain the reproducible high accurate data in spite of simple equipment. ...more

The ability to generate controlled, high-intensity electric and magnetic fields over the frequency range of 10 kHz to 100 MHz and a unique design make the EFG-02 the best choice for conducting immunity testing on large, heavy, or bulky DUTs. ...more

The Active H-Field Measurement Antenna HM525 is a loop antenna. The voltage at its output is proportional to the amplitude of the alternating magnetic field applied. For overview measurements, the antenna can be operated in broadband mode in the total frequency range from 100 Hz to 30 MHz. To obtain maximum sensitivity, the antenna can be loca ...more

Test a wide range of ELF magnetic fields, independent of measurement angle. Measure magnetic field radiation levels around power lines, appliances and industrial devices. Measure magnetic field radiation from 30Hz to 2000Hz. Displays micro Tesla and milli Gauss in the same tester  ...more

This system provides a high accuracy magnetic field in the range of 800 - 4000 Gauss with temperature tests in the range -50°C +150°C. Absolute accuracy : +/- 5 milligauss Stability : +/- 2 milligauss Polarity +4000 Gauss reversed to -4000 Gauss and regulated within 30 seconds. Possible to set 0 Gauss value out of regulation (0 +/- 100 milligauss) ...more

automated wafer magnetic test platform for MRAM and TFH device development and process control. This is the fastest, most accurate, and lowest Cost of Ownership tool on the market. A constant bias voltage option enables MTJ and advanced sensor development. The system can also be configured with a thermal option for stress analysis on devices. ...more

Electric field analyzers for low frequency fields, selective and broadband measurements. EFA-200 is for measuring magnetic fields. EFA-300 is for measuring magnetic and electric fields. Isotropic measurement with integral test probe and external standard 100 cm2 probe (accessory) or in case of EFA-300 with electrical cube ...more

CAYLAR manufactures custom magnets for Mass Spectrometers (Magnetic Sector), Small Ion Source Generators (Magnetic Mass Analyzer, Deflectors), equipped with Vacuum Segment and probe of NMR or Hall Effect Gaussmeter or Field Regulation. A specific application is Characterization Bench for Magnetic sensitive components, with dedicated devices : Therm ...more

The LDS V9 electrodynamic shaker is designed to test heavy loads at high levels over long continuous periods. It uses a revolutionary design of two magnetic gaps driven by one field coil to provide displacement up to 75 mm (3 in) with a peak velocity of 3 m/s (118 in/s ...more

The magnetic field generator and analyzer MGA 8000 allows susceptibility tests against magnetic fields from DC to 100 kHz according to the standard EN 55103-2 (product standard for proffesional audio, video and light control technics) and their measurement according to EN 55103-1. Besides that the MGA 8000 is designed to lead through susceptibi ...more

A.H. Systems' designs, manufactures and delivers high performance Loop Antennas for a wide range of magnetic field testing. Whether used in a set to measure shielding effectiveness per MIL-STD 285 and NSA 65-6 or individually to satisfy specific requirements, ...more

The A.H. Systems' set of H-Field Rods provide an accurate standard for magnetic field testing. The rods are available individually or in a set of four to cover the frequency range of 100 Hz to 30 MHz. ...more

An advanced, multi-capability, low-cost EMC immunity test system to address a broad range of testing capabilities including Bellcore, UL, IEC, ANSI/IEEE, CCITT and ETSI. Designed to test well beyond the requirements of the CE Mark, users can configure the EMCPro Plus to meet specific test requirements using the full line of options and accesso ...more

Shielded transformer jaw opens to 1.2". 100uA high resolution. Least affected by external magnetic field,providing wide measuring range from very small to large current. Designed to safety standard IEC 61010-2-032:over-voltage CAT.III,300V and pollution degree 2. Data hold function to allow for easy reading in dimly lit or hard-to-reach l ...more

The RF 2 probe set contains magnetic field probes for precompliance tests of printed circuit boards. Measuring the magnetic fields in the area of the module, conducting tracks, components and the modules of the supply system is the basis for selective measures to reduce disturbance emissions. ...more

The Helmholtz coil system concept, developed by a German physicist over a century ago, is a system that is normally used to generate magnetic field levels of specified volume and uniformity, allowing scientists and engineers to perform numerous experiments and test functions that require a known ambient magnetic field. Helmholtz field generatio ...more

The RF 1 probe set contains magnetic field probes and an E-field probe for precompliance tests of printed circuit boards. Measuring the magnetic fields in the area of the module, conducting tracks, components and the modules of the supply system is the basis for selective measures to reduce disturbance emissions. ...more

Power Frequency and Impulse magnetic fields can be generated using standard Haefely EMC Technology's test equipment and coil antennas to suit the test equipment dimensions. Antennas from 1m x 1m to 2m x 2.6m are available as standard. ...more

The Hearing Aid Compatibility Test Kit has been designed to provide a turnkey solution to the problem of testing the magnetic field properties of a telephone design for HAC. The system Test Program software requires only three steps to evaluate the HAC performance of a telephone. An optional non-magnetic handset fixture is available on request ...more

Damped oscillatory magnetic fields generated by the switching of high voltage buss bars by isolators at power substations frequently degrade electrical and electronic equipment. In accord with the IEC 1000-4-10 specification requirements the Fischer Custom Communications, Inc. IEC 1000-4-10 system develops the damped sinusoid current waveform i ...more

The new ECOMPACT 4 with the 3-phase coupling/decoupling unit ECOUPLER 4 combines the best of all worlds: Performance, flexibility, economy and the famous Haefely quality and reliability. The ECOMPACT 4 is an ultra-compact immunity tester that performs all the most commonly used transient immunity tests, including Surge, EFT, Dips / Interrupts ...more

The PC-based test system MAG_1030 is capable of performing full compliance tests in accordance with EN 55103, EN 61000-4-8, MIL-STD-461E, SAE and similar standards. Magnetic fields may as well be measured and generated.  ...more

The rotor tester system determines the symmetry of multipolar magnetized DC permanent magnet rotors. The measuring system measures the magnetic field strength over the surface of a rotating rotor and determines the distribution of the field, its peak values, zero crossovers and their distance, as well as the total flux of each pole. Depending o ...more

Standard one meter loop configurations as well as large custom loops up to 3 meters by 4 meters are now available for IEC-1000-4-8 testing along with 125 ampere and 1000 ampere generators. For large systems that cannot be elevated above the ground plane, the new proximity array allows you to test IEC 1000-4-8. ...more