Leakage Test

AC Hipot Test Performs AC dielectric testing (hipot) over the voltage range from 50 to 5000VAC RMS. Leakage current detection is programmable from 1µA to 40mA, making the 6100 ideal for testing medical products and instruments having a wide range of leakage currents. DC Hipot Test DC dielectric testing is possible from 50 to 6000VDC with leaka ...more

Ideally designed for non-invasive checks of insulation condition, the Fluke 360 leakage meter allows you to perform tests without powering down the installation or disconnecting equipment - saving you time, without compromising on quality or safety. The unique jaw design of the Fluke 360 AC Leakage Current Clamp Meter eliminates the influence ...more

The 180 Electrical Safety Analyzer is a lightweight and ultra-portable test device for ECG-device-leakage and isolation testing. ...more

The B+K Precision model 520C Transistor Tester is designed for in circuit and out of circuit transistor testing with special features for making additional tests on devices out of circuit. The instrument is designed for a minimum amount of control manipulation, making for rapid testing of most devices. Determines good or bad transistors, FET's ...more

The model 307A insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It ...more

The model 308A insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It ...more

This insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It is also u ...more

This insulation tester is intended primarily for periodic testing of industrial motors, transformers, electrical wiring, and cable insulation for signs of deterioration. Low readings may indicate impending failure allowing for permit replacement of suspect component during routine maintenance rather than risking component failure. It is also u ...more

Wide Measurement Ranges: Measure resistance from 10k to 1P with basic accuracy of ±2% up to 1T. Measure Leakage Current down to 1pA with basic accuracy of ±2%. Programmable Test Voltage: From 10V to 1kV in 1V increments on the 1868A Model, and from 50V to 5kV in 1V increments and on the 1868D Model. Powerful Charge Capability: The 1868A Model ...more

Enables non-contact measurements of ground conductors without need for auxiliary ground spikes. Autoranging ground resistance easurements from 0.025Ω to 1500Ω with 0.002Ω resolution. True RMS AC Leakage current range of 0.2mA to 30A with 1.000mA resolution. Programmable Datalogging with 116 data points. Programmable Hi/Lo Alarm ...more

The 550 is used to check high voltage circuits on Hybrid cards for leaks to ground. The 550 can supply 250V, 500V and 1000V test voltages for doing complete insulation testing. You can not easily test for high voltage leakage without a high volt test source. The 550 is auto-ranging and can measure up to 2000 MegaOhm with a resolution of 1 K Ohm. ...more

Larger Clamp Size (1.25"). Backlight. Ground resistance (0.1 to 1200?). Ground leakage current to 30A. Ground continuity loop test. Audible alarm. Data Storage  ...more

Accurate ground resistance measurement from 0.025 to 1500 Ohms. TRMS current measurement including leakage current. Continuity beep if the resistance is lower than 40.00 Ohms  ...more

Get your safety testing off to a rapid start with the new concept in portable appliance testing. Transmille has redefined PAT operation for the ultimate in speed and simplicity of use. Pressing the CLASS 1 button sets the 5080 to automatically sequence through a visual check, fuse check, earth bond resistance, insulation resistance and leakage ...more

High voltage testing devices from the GLP1e family serve for testing the insulating capability and the electric strength (clearance and leakage path) at electric modules and componentry in line with a great variety of national and international regulations ...more

In order to comply with any laboratory or production application, FMG series is constantly following the international standard evolutions, and is one of the 4 tests required by the Electrical Safety. Leakage current measurement, single and three phases power measurement, cosφ , functional test ...more

The TVR6100 is a multipurpose, versatile Binning Tester. It can be used to classify parameters, including TRR (reverse recovery time), VF (forward voltage, IF is up to 100A), VBR (reserve breakdown voltage) and IR (reverse leakage current). Moreover, it can test IR SURGE, ΔVR(delta reverse voltage) and IR parameters at the same time. Each ...more

The Model 400 Open/Short Tester is used to test for open and/or shorted lead bonds. The tester can also be used to measure leakage currents.  ...more

Transformer Diagnostic System provides automatic testing of important transformer parameters within one portable system. System is the ideal tool for comprehensive testing of the following parameters of a power transformer: • Winding resistance • Turns ratio and excitation current • On-load tap changer condition • Leakage reactance • Insulation con ...more

VLF testing is the proven replacement for the traditional DC Hipot Acceptance or "Proof" test. With more than 700 Very Low Frequency (VLF) units sold, and over 16 years of field use, HDW offers the only VLF units which are capable of measuring true leakage current. Our VLF technology provides the most meaningful test results because it is the o ...more

Our HT10kVac/dc has AC and DC output. Leakage current limits can be set with the front panel knob from 0.5mA to 10mA ac and 0.25mA to 5mA dc. Normal operation stops testing when a leakage current greater than the set amount or when a dielectric breakdown is encountered. If desired, testing can be set to continue to burn problem areas. ...more

A breakthrough in Portable Appliance Testing. Battery powered, with an emphasis on simplicity of use. As 5080 PLUS...110V ? Fuse Test ? Lead Check ? Self Check. BOND CURRENT @ 25A / 10A / 100mA. INSULATION RESISTANCE @ 500V. LEAKAGE CURRENT @ 230VDUAL. VOLTAGE 100V / 240V. IEC / EXTENSION LEAD CHECK  ...more

With high voltage testers air and leakage paths are tested. Measurement of test voltages is specified in the relevant standards (IEC, EN, UL, BS, VDE, etc.). As a general rule applies: rated voltage x 2 + 1000 V ...more

Our 120 VAC input Dielectric Strength Tester provides a wide range of voltage (0 to 14 kVDC) for checking leakage currents in a myriad of applications. Conveniently packaged for a 19" rack mount chassis, the CS5658A1 tester has digital voltage and current meters on the front panel. It also provides a high speed electronic cutout adjustable ...more

Sheath Tester MMG 5 is mainly designed for the withstand voltage testing of cable sheaths made of PE or PVC as well as for locating sheath faults on shielded plastic-insulated cables and the detection of earth-leakage faults in plastic-sheathed cables. In conjunction with Sheath Fault Prelocation Device MVG 5, sheath faults can be prelocated. ...more