Leakage Current Clamps

Ideally designed for non-invasive checks of insulation condition, the Fluke 360 leakage meter allows you to perform tests without powering down the installation or disconnecting equipment - saving you time, without compromising on quality or safety. The unique jaw design of the Fluke 360 AC Leakage Current Clamp Meter eliminates the influence ...more

Larger Clamp Size (1.25"). Backlight. Ground resistance (0.1 to 1200?). Ground leakage current to 30A. Ground continuity loop test. Audible alarm. Data Storage  ...more

The TRMS Clamp-On Leakage Current Meter Model 565 is designed to measure low AC currents, which are typically leakage currents in ground conductors. Low currents are measured using either 60mA or the 600mA range.  ...more

Accurate ground resistance measurement from 0.025 to 1500 Ohms. TRMS current measurement including leakage current. Continuity beep if the resistance is lower than 40.00 Ohms  ...more

A fully portable test station with digital amp and volt meters, fan cooled, Heavy Duty Carbon Pile Rheostat for complete electrical system loading and battery testing. Tests alternator and starter motor output 0-1000 amps current draw. Carbon pile load 500Amps (1000CCA). When used in conjunction with MMCA-1000 inductive current clamp, unit will ...more

Detection of improper shield currents resulting from earthing, equipotential bonding or EMC problems. Measurement of leakage currents, e.g. leakage and fault currents, current pick-up of instruments in service and maintenance areas, (DIN VDE 0701/0702 measurements). ...more

A very high quality earth leakage clamp meter with resolution down to 0.01mA and a basic accuracy of 0.05mA. Ideal for identifying appliances or circuits which are causing RCDs to trip. Comparison feature allows values between 1mA and 20mA to be set and the meter will beep if it measures above the pre set comparison level. This triggering allow ...more

A fully portable test station with digital amp and volt meters, fan cooled, heavy duty carbon pile rheostat for complete electrical system loading and battery testing. Tests alternator and starter motor output 0-1000 amps current draw. Carbon pile load 1000Amps (2000CCA). When used in conjunction with MMCA-1000 inductive current clamp, unit wil ...more

Earth resistance clamp is a breakthrough from traditional tester. Neither the supplementary earth leads nor the break earth equipment is necessary. Ground resistance result can be get safe and fast only by clamping the ground line. Additionally, current testing is also provided. High sensitivity clamp meter can measure the leakage current to 1 ...more

The STB Current Leakage Detector is a great concept in preventative maintenance. As insulation ages, it’s insulating properties often deteriorate. Humidity and foreign matter aid in this deterioration. The STB current leakage detector will indicate ground faults and electrical leakage while the equipment is in operation. ...more

Easily monitor leak current fluctuations. Wide bandwidth, 5 Hz to 15 kHz (Waveform output). High-sensitivity with a full scale of 10 mA (resolution:10 µA). High-accuracy at ±1 %. True RMS measurement. Analyzer functions, for filtering and output signals  ...more

Record AC Current on Two Channels. Range is 100 mA AC and 1000 mA AC. 100 mA AC and 1000 mA AC. 9657 Clamp On Sensor AC 1.0 Amp  ...more

SIRIUS89N is a complete model to perform all safety tests in compliance to VDE 0413, measure of values of environmental parameters (temperature/humidity, illuminance, sound level with optional probes), leakage current with optional clamp and to perform a network power quality of single phase in compliance to EN50160 guideline. ...more

Digital clamp meter designed for leakage current measurement. Least affected by external stray magnetic field. The minimum resolution is 0.1mA. Four AC current ranges:400mA/4A/40A/400A. Data hold function,peak hold function  ...more

HT77 TRMS clamp model is designed by using a special nucleus for measurement of very low current and is an essential instrument for leakage currents detection which are the typical problem about RCD's tripping. It is also employed for measurements of first fault currents in medical rooms. HT77 was realised according to IEC/EN61010-1 safety standard ...more

HT96U model is a transducer clamp for AC current measures with 1-100-1000A/1V ranges with high resolution (1mA) in order to perform leakage current measurements on electrical installations. The model is able to clamping cable with maximum diameter of 54mm or 35x35 mm and 50x12 mm bars. ...more

The Meterman AC50 Leakage Current Clamp Multimeter offers 10 microAmp resolution for measuring low ac current. It’s great for applications requiring measurement of leakage and fault currents, and current pick-up of instruments in service and maintenance areas, (DIN VDE 0701/0702 measurements). ...more

Water and dust proof construction. The instrument is protected against water and dust. True RMS for accurate measurement of non-sinusoidal waveform current. Selectable frequency response of 50/60Hz only or up to 1kHz. Automatically turns power off in about 30 minutes to conserve battery life.  ...more

Leakage current measurement with current range from 40mA to 400A. Manual range switching and auto power-off functions. 40mm in diameter of measurable conductor ...more

Frequency Selector Switch to eliminate the effect of harmonics. Three AC current ranges : 40mA/400mA/400A. Data hold function. Peak hold function. Sleep function to save battery. Designed to international safety standard IEC61010-1 CAT.III 300V  ...more

Extra wide transformer jaws are best suited for clamping on all three or four wires (3phases) together for leakage current measurement. Frequency filter switch to eliminate the effect of harmonics. Peak hold function. Analogue output terminal.  ...more

Exclusive model for Leakage current measurement with current ranges from 3mA to 60A. Durability of clamp is more then 50,000 opening/closing events. ...more

At first, the NI 333 looks like a normal current clamp. Nevertheless, the special integrated technique of the jaw enables the user to measure very low or differential currents. In the range up to 10µA, the clamp can even measure with a resolution of 10µA. For normal use, the clamp can measure up to 60A, voltage up to 400V and resistance up to 4 ...more

Frequency Selector Switch to eliminate the effect of harmonics. Three AC current ranges 20mA/200mA/200A. 20mA range with a minimum resolution of 0.01mA. Auto power-off function (automatically turns off in about 10 minutes).  Rotary switch for easy one finger power-on and range selection.  ...more

Frequency Selector Switch to eliminate the effect of harmonics. Three AC current ranges:40mA/400mA/400A. Data hold function. Peak hold function. Sleep function to save battery. Designed to international safety standard IEC61010-1 CAT.III 300V  ...more