Showing results: 256 - 270 of 293 items found.
-
448 -
SCI
Our 448 model is a 4-in-1 tester with 500VA AC Hipot, DC Hipot, Insulation Resistance and Ground Bond testing capabilities. The 448 is capable of a 500VA AC Hipot output to comply with 100mA leakage current test compliance requirements. This tester features a simple design and easy-to-use interface, reducing setup time and increasing production-line throughput for your application.
-
JP3X Series -
Danbridge a/s
The Danbridge non-destructive High Voltage Insulation Testers meet the demands for a gentle method of testing insulation condition and detecting leakage currents while protecting hardware, components and materials. Danbridge have two High Voltage Insulation Testers depending on requirements - JP30A can test using up to 30k volt, while JP36A is used when voltages up to 36k volt are desired.
-
P4330 -
P3 International Corp.
Now you can protect your valuable electronics and find out what they are actually costing you. Simply connect these appliances into the Kill A Watt® PS-10, and it will assess how efficient they are while the built-in surge protection keeps them safe. Advanced features such as over current, over voltage, and no load detection provide clean, safe power to your expensive equipment. Check the quality of your power by monitoring Voltage, Line Frequency, Amperage, KWH, Current Leakage and more. Now you’ll know how much power your entire computer or home theater system is using. With the innovative Kill A Watt PS-10 you’ll have peace of mind in more ways than one.
-
Series C63 -
Teledyne Defense Electronics Relays & Coax Switch
Series C63 solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin mini-DIP package. These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6Available options include:C63-10 1A, 60Vdc Load; 8-20mAdc Control; through-hole mountedSC63-10 1A, 60Vdc Load; 8-20mAdc Control; surface mounted
-
Part No. ZD20CF -
Teledyne Defense Electronics Relays & Coax Switch
Series ZD20CF solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin DIP package These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6Available options include:ZD20CF 2A, 60Vdc Load; 8-20mAdc Control; through hole mountedSZD20CF 2A, 60Vdc Load; 8-20mAdc Control; surface mounted
-
Part No. ZD24CC -
Teledyne Defense Electronics Relays & Coax Switch
Series ZD24CC solid-state relays use an advanced design capable of switching heavy loads in a physically small 6-pin DIP package These relays have a power FET output that ensures low ON resistance and low leakage current. Optical isolation ensures complete protection of signal lines, power and ground bus and control circuits from switching noise and EMI.MSL 6Available options include:ZD24CC 0.5A, 80Vdc Load; 8-20mAdc Control; through hole mountedSZD24CC 0.5A, 80Vdc Load; 8-20mAdc Control; surface mounted
-
Bloomy Controls, Inc.
The BMS Environmental Test System is a configurable platform simulating the essential signals used by Battery Management Systems (BMS) and cell-monitoring modules with the ability to perform environmental testing on multiple BMS units simultaneously. The system implements single-point value testing to evaluate specific BMS functions such as cell over and under voltage scenarios, cell leakage current, lost communications, or faulty system IO.
-
19501-K -
Chroma Systems Solutions, Inc.
The Chroma 19501-K Partial Discharge Tester is an instrument equipped with AC hipot test and partial discharge detection functions, providing 0.1kV~10kV of AC output, 0.01μA~ 300μA of leakage current, and 1pC~2000pC partial discharge detect ion range for measurement. Chroma 19501-K Partial Discharge Tester is compliant to the IEC60270-1 standard in particular the partial discharge testing requirements for high voltage.
-
ZX3 -
Allied Edison LLC
The ZX3 is a ground fault locator that finds grounds (current leakage) on a battery system positive rail, the negative rail, on both rails simultaneously, in a field device, battery bank or solar array/string, regardless if they are high resistance or low resistance or in a capacitive environment. It also can provide more information about the DC ground than any other equipment available, providing maximum analyzing capabilities.
-
Labodam
Labodam sand and dust test chambers are corrosion resistant equipment that tests the stability, quality, reactivity, and characterists of products against the sand and dust exposed environmental conditions. These test chambers are carefully designed as per the CE and ISO standards and provide rpotection against current leakage, overload, over-current, short circuit, over temperature, motor overheating, and over pressure for safe and precise results.
-
ST-1520 -
Standard Electric Works Co., Ltd
● Capable of measuring earth resistance and earth voltage.● 2mA measuring current permits the testing of earth resistance without tripping earth leakage current breakers in the circuit under test.● Auto power off function.● The timer operates automatically for about three to five minutes when the "PUSH BUTTON SWITCH" and "TIMER ON BUTTON" are pressed together. This will keep test "ON" for the duration of the timer.● Timer for test function (count 3-5 minutes).● Battery operated.● Data hold function.● Small and light weight.● Calibration performed with supplied test leads.
-
LXinstruments GmbH
HV test enclosure for testing medical products (patient monitors). Insulated test booth with large space for DUT.3 different test nests for adapting different devices.Displays from patient monitors are checked. For this, insulation tests and leakage current measurements must be carried out. Ensuring the standard-compliant test. For the safety of the operating personnel, the test cell is electrically locked while the high voltage measurement is active.
-
Chroma 11210 -
Chroma Systems Solutions, Inc.
Chroma 11210 battery cell insulation tester is an instrument used for accurately measuring leakage current (LC) and insulation resistance(IR) of battery jelly-roll/dry-cell as well as other insulation materials. In addition to standard LC/IR measurement, the 11210 has a unique function that detects partial discharge (PD) or flashover that may have occurred inside the insulation material during the high voltage insulation testing process.
-
Compliance West USA, Inc
The newest product of our Hipot Line Testers, the UL Listed HT-S series hipot now comes with an adjustable ground continuity test in range of 0.08 - 1.50 , and Auto-offset for test leads up to 1.00 . Performs 0-2000 AC Hipot Test. Neutral/Hot to Ground Leakage current test up to 20 mA AC. Easy to use and connect. Ships complete with cables, manual, and a Calibration Certificate.
-
Aarohi Embedded Systems Pvt. Ltd
AAROHI make high voltage tester is specially designed to test induction & submersible motors with cutting edge technology.High Voltage Tester is manufactured as per the International set standards and regulations. This High Voltage Testers are available in AC and DC types and are used for testing HV cables after installation and repair for ensuring efficient performance. It also indicates voltage withstands level and current leakage level of the cable during the testing period.