BC-400-PB - Fieldbus Shield Digital Leakage Current Clamp Detection of improper shield currents resulting from earthing, equipotential bonding or EMC problems. Measurement of leakage currents, e.g. leakage and fault currents, current pick-up of instruments in service and maintenance areas, (DIN VDE 0701/0702 measurements).

LC-2R - Touch Current (Leakage) Test Set The test for leakage current in mains operated equipment is one of the most primary & important tests to verify the quality & electrical safety characteristics of products as required by national & international regulatory agencies such as BIS, IEC, UL, CSA, VDE, DIN, BSI, etc.

M450LT - Leakage Current Tester Performs leakage current tests in compliance with IEC 601, UL 544, UL 2601 and other medical and non-medical standards. Add Rod-L Hipot & Ground Continuity testers to build a complete modular automatic test systerm

4671 - Leakage Current Tester 10µA Ultra High Resolution Large Conductor Diameter (30mm) AC Current in 5 Ranges (40mA, 400mA, 4A, 40A, 60A) Wide Frequency Response (40Hz-1KHz) ACA, ACV, Ω and Continuity Large 3¾ Digit LCD (4000 Count) 40 Segment Fast Bargraph Display (20 times/sec.) Data Hold and Max / Min Hold Relative Measurement 600 Vrms Overload Protection in Resistance Range

AI 5601D - leakage current tester The safety test of electrical devices must, after having been tested without current and depending on the relevant test standard, be completed by a line leakage measurement with increased rated voltage. Only by means of a line leakage test is it possible to activate the internal controls in case of electro-mechanical devices

HT77 - Clamp for AC TRMS Leakage Current Measurements HT77 TRMS clamp model is designed by using a special nucleus for measurement of very low current and is an essential instrument for leakage currents detection which are the typical problem about RCD's tripping. It is also employed for measurements of first fault currents in medical rooms. HT77 was realised according to IEC/EN61010-1 safety standard in CAT IV 600V and CAT III 600V for current and voltage measurements accordingly

ST-9809/9810 - AC Leakage Current Tester AC leakage current tester 9809 is multifunctional DMM with a very good resolution of 10µA. It is very useful for power system check and installation. With the measuring range up to 100A, this tester is great appliance installation or car application

352 - The Short Stop AC Leakage Current Tester with Hi-Pot The BEST tester available for electrical repair. If you must verify the safety and performance of electrical products you will not find a better value. Tests products for short circuits, continuity of the ground wire, hi-pot, leakage current and current draw. The Model 352 Short Stop Tester is in use by thousands of electrical repair shops, and manufacturers - Black and Decker, SB Power Tool, Makita USA, Milwaukee Electric Tool and Monsanto Corp.

WB5055 - Leakage Current Tester :Leakage Current Tester

RCT-18 - Leakage Current Measurement Leakage current measurements with DCV output for recorder

2620 - Leakage Current Meters and Probes The Model 2620 measures leakage current shunted to ground caused by insulation faults. It enables the operator to locate failures when they occur, or anticipate them before they occur, without shutting down equipment or spending hours troubleshooting

TH2685C - Electrolytic Capacitor Leakage Current Meter Electrolytic leakage current meter is a measurement instrument automatically measuring electrolytic capacitor leakage current with continuously adjustable voltage, digital display of voltage and charge time, analog meter indication of current, and automatic conversion of charge and measurement. TH2687C has ultrahigh voltage (650V), and TH2688C has large current (max. charge current of 400mA).

565 - Leakage Current Meters and Probes The TRMS Clamp-On Leakage Current Meter Model 565 is designed to measure low AC currents, which are typically leakage currents in ground conductors. Low currents are measured using either 60mA or the 600mA range. 

92-4A - Leakage current tester 92-4A single phase earthbound The 92-4A serves for the norm concurring measuring and evaluation of leakage currents. Due to the integrated computer system the device can be used as an independent measuring system or as a component in an automated device tester.

229-2 - AC Leakage Current Tester Testing for dangerous small leakage currents is easy with the Simpson Model 229-2 Leakage Current Tester. For use in appliance field service, in the lab, or in production, the 229-2 approximates the human threshold of perception in detecting hazardous AC leakage current. The 229-2 comes with test leads with alligator clips, manual and batteries. 

LEAKAGE CURRENT TESTERS Measures Leakage Current in accordance with UL, CSA, EN, and IEC/ International Standards. Includes ability to perform open neutral, open ground, and line polarity forward/reverse test conditions. True RMS meter accurately measures both sinusoidal and non-sinusoidal waveshapes. This is important when testing products using a switch mode power supply which can generate non-sinusoidal leakage currents. Calibrated, traceable to NIST.

MN103 - Leakage Current Meters and Probes The MN103 measures leakage current and low currents from 1mA, and measures current on 5A secondaries. Provides AC current measuring capabilities to instruments with mV inputs. The output of the MN103 is a 5ft lead with safety 4mm safety plug. 

TH2686A - Electrolytic Capacitor Leakage Current Meter Electrolytic capacitor leakage current meter is a measurement instrument automatically measuring parameters of electrolytic capacitor leakage current with continuous- adjustment measurement voltage, analog meter indication of voltage and current, automatic conversion of charge and measurement, max. measurement voltage of 200V for TH2685A, 500V for TH2686A, max. current of 30mA, max. charge current of 200mA,

Leakage current tester 90-2Msingle phase for system applications The 90-2M serves for the leakage current measurement of single-phase equipment. Due to the modular construction measuring circuits of different norms can be covered. The measuring frequency range is 1 MHz.

ST-05 - SAFETY TESTERS ( CURRENT LEAKAGE TESTERS ) Safety Tester Model ST-05 is a test set for testing small equipment powered by 120V 60 Hz, from an approved U-ground source. Test also can be run on double-insulated tools an on appliances with two-pin parallel plugs.

BENNING CM 9 - Leakage Current Clamp Error-related leakage currents are caused by weak insulation or insulation damages. The BENNING CM 9 allows quick and precise localization of all error types. By means of preventive measurements, possible damages due to uncontrolled leakage currents can be avoided in advance.

4680 - Clamp-On Ground Resistance and Leakage Current Tester MECO 4680 Clamp-On Ground Resistance and Leakage Current Tester is a non-contact type innovative solution for measuring ground resistance and leakage current of electrical installations like transmission poles, transformers, lightning arrestors, motors, high-voltage appliances and cables. It can be used in multi-grounded systems without disconnecting the ground connection of the circuits.

LCM II - Leakage Current Monitor LCM is a unique portable equipment for leakage current measurements is developed for in-service measurements of the resistive component of the continuous leakage current of gapless metal oxide surge arresters (MOSA's). The Leakage