Jitter

The FS5000 Jitterlyzer performs physical layer serial bus jitter evaluation. It can inject controlled jitter and measure the characteristics of incoming jitter. When teamed with a protocol analyzer, it can correlate these measurements with protocol analysis . The benefits of this low-cost solution are numerous. Physical-layer tests can be perf ...more

The PM 6681R sets the new standard for measurement and analysis of time intervals, frequency, phase and jitter. For development, calibration, or challenging production test applications, the PM 6681R is the leader. ...more

With its revolutionary technology, the PM 6681 from Fluke sets the standard for measurement of time intervals, frequency, phase and jitter. PM 6681 is much more than just a timer/counter. Its speed and resolution are comparable to the most accurate time and frequency modulation domain analyzers. ...more

NetDisturb is an IP network emulator - simulator software that can generate impairments (latency, delay, jitter, limited bandwidth and lost packets) over IP networks. It works on 10/100 and 1 gigabit platforms. Download free trial. ...more

The NIC is a scalable solution for verifying and qualifying the performance of today's multiprotocol global communications networks.With a flexible software/firmware-based architecture, the scalable NIC Plus combines in a single platform the multitude of traditional hardware-based test sets required to install, maintain, and monitor high-speed ...more

The KJM6765 employs the time interval method for measuring jitter in CD players as well as in DVD players, based on principles successfully used in the KJM6755A.  ...more

Two fully programmable channels combined/mixed at the output. Controlled by version 2 of the F100 software for PC and PalmOS. 32 bit DDS (Direct Digital Wave Synthesis) technology. Low jitter high speed channel A from 0 to over 20 MHZ (up to 30 MHZ for reduced amplitude sine wave). Channel A programmable for square or sine wave output. Channel ...more

The KJM6775 is an improved version of the KJM6765 and the KJM6755A which are widely used in the market. KIKUSUI proudly presents this cutting edge model developed to support the next generation media. ...more

The KJM6335 is a dedicated time-interval jitter meter for CD players. As the market for DVD players expands, the demand for measurement by the time-interval method rather than the 3T or 22T method based on the current CD jitter measurement principle is beginning to increase. ...more

Time Interval Analyzer (TIA) Handles DVD, CD and CD-R/RW. Historgram Color LCD Display Shows Jitter History, RF Data, Amplitude, Average Sigma Reading and Clock. Measures Jitter at 3T Through 11T + 14T. Jitter Readings in % Clock Frequency and Sigma ...more

The XCLK1 is a high frequency clock generator PMC/XMC module that is able to provide up to five synchronized sample clocks for high speed I/O products such as analog to digital converters. ...more

The 60-983 is an LXI compatible Wired Trigger Bus Terminator (WTB) designed to be attached to the end of a WTB cable. The LXI WTB uses a transmission line cable to connect LXI devices together that support the WTB capability of the LXI standard. Like all transmissions it needs to be correctly terminated to avoid reflections that could change t ...more

Taking into consideration all the functionalities identified as necessary on the production line through the use of the KJM6765 and KJM6755A jitter meters, the time interval jitter meters KJM6710 and KJM6310 both combine a concentrated set of capabilities into a single compact unit.  ...more

The LE 1871 Jitter Meter is designed to measure the jitter conforming to Blu-ray Disc (Part 1, version 1.0, June 2002) standards. Combining time interval analyzer TIA as well as digital processing methods for jitter measurement, enables accurate measurement with high throughput for adjusting and inspecting optical pickups on production lines. ...more

TIA Digital Processing Handles DVD, CD and CD-R/RW. High-Speed, Accurate Simultaneous RF Data Level and Jitter. Measures Jitter at 3T Through 11T + 14T. Jitter Readings in % Clock Frequency and Sigma. Measurements at Rise, Fall and Both Data Edge. High Sensitivity - Accurate Readings at 50 mV or More ...more

The KJM6235A jitter meter is an instrument that measures the amount of jitter in output signals (EFM signals:Eight to Fourteen Modulation) from optical pickups used in compact disk (CD) players. ...more

The LE 1876 Jitter Meter is designed to measure the jitter conforming to Blu-ray Disc (Part 1, version 1.0, June 2002) standards. Combining time interval analyzer TIA as well as digital processing methods for jitter measurement, enables accurate measurement with high throughput for adjusting and inspecting optical pickups on production lines. ...more

The DVD Specifications for Read-Only Discs Ver. 1.0, Aug. 1996 (hereafter referred to as the DVD Book) specify the jitter measurement method as follows: Time differences between all edges of an RF signal and a clock signal generated from the RF signal are measured to obtain their variation (a value) as jitter.  ...more

The DTG5000 Series combines the power of a data generator with the capabilities of a pulse generator in a versatile, bench-top form factor, shortening the duration of complex test procedures and simplifying the generation of low-jitter, high-accuracy clock signals, parallel or serial data across multiple channels. ...more

80SJNB is a comprehensive jitter, noise, and bit error ratio (BER) analysis application for serial data signal impairment characterization. ...more

SerialXpress® is a powerful easy to use software package to synthesize high speed serial data signals, for arbitrary waveform generators (AWG). It runs as an integral part of the AWG7000 and AWG5000 series arbitrary waveform generators or from an external PC. ...more

The CATS SA3 Advanced measures all relevant parameters and provides easy-to-analyze information about the disc with high resolution Surface Presentation. SA3 Advanced measures jitter and length deviation. With these important parameters, engineers can have confi dence in disc quality and process stability. ...more

The Linktropy 4500 WAN Emulator combines unsurpassed precision with unbeatable prices. The Linktropy 4500 simulates wide-area network bandwidth, delay, jitter, packet loss, congestion, and other important link impairments at speeds of up to 155 Mbps. ...more

Multi-function instrument performs DS-1 and DS-3 PCM testing, analog TMS and signaling analysis and jitter analysis. Set is configured by selecting from option cards for six option slots available. (See below) BASIC DS-1: The starter unit has two DS-1 transmitters and receivers for monitor, terminal or drop and insert functions and 24 channel ...more

A real time, USB interfaced, self powered, DVB-T+H transport stream analyzer with comprehensive automatic analysis of different services, PIDS, bursts, structures, on/off times, bandwidth utilization, transport layers, delta T jitter, and other critical DVB-T+H parameters for use in Field and Lab applications. Includes ability to store TS on your H ...more