Inductors

Pinpoints bad capacitors and inductors "in-circuit," and automatically tells you when further out-of-circuit tests are required. Analyzes capacitors for all four failures out-of-circuit: - Value from 1 pF to 20 F - Equivalent series resistance - Leakage with up to 1,000 volts applied - Dielectric absorption. Tests SMT components "in-circuit" and a ...more

The ITC55140 programmable inductor box uses solid state switching and was designed to work with all of ITC's 55X00 series test systems to allow high-speed selection of inductance values from .01-149.9mH.  ...more

The ESI Model 6650A Visual Test System provides automatic visual inspection of surface-mount MLCC, inductor, bead and varistor chips. Two machine configurations are offered: Four or six sides of the chip are inspected and preset limits sort chips in up to five categories based on inspection results.  ...more

This synthesized In-circuit LCR/ESR Meter is a high accuracy test instrument used for measuring inductors, capacitors and resistors with a basic accuracy of 0,1 %. ...more

. Newly upgraded adapter TA01 from an old Hewllet Packard system controller to SCADUS Windows controller. Testing: Resistors, Capacitors, Inductors. You can measure resistance, capacitance and inductance. You also can set up a reference value and compare in percent points the deviation from reference value. For capacitors and inductors adapter meas ...more

The oscillating wave test system (OWTS) is used to iden-tify, evaluate and locate partial discharge (PD) faults in cable insulation and accessories in all types of high volt-age power cables. The system consists of a notebook as a WLAN control unit and a HV unit. The HV unit contains a HV source and a resonance inductor with an integrated elect ...more

The ITC5516 High Current External Inductor Box is specifically designed to work with the ITC55300 High-Current Inductive Load Tester and provides inductance range from 0.001 mH to 0.300 mH in 0.001mH steps.   ...more

This high accuracy LCR meter can perform the inductor, capacitor and resistor measurement up to 100 kHz within 0,2 % basic accuracy. ...more

Wide measurement Ranges for Capacitors, Resistors and Inductors. Menus and parameters are displayed on an easy to read 320x 240 Graphics LCD with backlight. Open and short-circuit compensation for accurate zeroing ...more

The REN Test Module RTM-1 provides all the additional passive components required for the REN test, as detailed in Britsh standard BS6305 or NTR3, all in one unit. The 3.6H inductor and 1890 ohm resistance are placed in series with the ringing voltage terminals, and a simulated bell is catered for with a 55H inductor and 7000 ohm series resista ...more

The 40-280 series provides a cost effective, high density solution for applications requiring a high channel count of simple resistor configurations. The 40-280 provides up to 48 isolated channels, each of which can be programmed as a short circuit, an open circuit or a fixed resistor value. Modules are supplied without any resistors fitted, perm ...more

The Feeding Bridge FB-1 is designed according to the specification shown in the UK BSI standard BS6317. It consists of a voltage regulated power supply feeding via two inductors to the equipment under test. External signals can be fed to the equipment via two capacitively coupled inputs, these being terminated by another set of inductors across ...more

Suitable for LPF, HPF and BPF design and experiments. Low coefficient characteristics. Low residual inductance! ...more

The Atlas LCR automatically identifies and analyses almost any passive component (Inductor, Capacitor or Resistor). It measures it's parameters using automatically selected test frequencies (DC, 1kHz, 15kHz and 200kHz). Inductance from 1uH to 10H, Capacitance from 1pF to 10,000uF and Resistance from 1ohm to 2Mohm. ...more

The As-513 can be used as an electronic load device for load testing AC power supplies and power equipment (instead of resistors, inductors, capacitors, or dummy network). ...more

The LC200 Digital Capacitance and Inductance Tester features a large 3.5 digit LCD display and 12 total ranges (7 ranges for capacitors and 5 ranges for inductors), also supplied with yellow rubber holster and test leads. Highly accurate with Auto-Zero adjusts and overloads indication. It is a very handy piece of test equipment for general trouble ...more

The MQ-1601 is designed for measurements of the figure of merit, Q, of inductors and capacitors. Effective values of inductance, capacitance, resistance, distributed capacitance, and high frequency cables can be determined. The overall frequency range is from 15.5kHz to 50MHz settable with use of a 6-digit counter display. ...more

Has frequency response function, analysis function of AC signal voltage/current and DC bias voltage/current. It can be used to analyze electronic characteristics of microphone, resonator, inductor, ceramic capacitor, LCD display, and transformer. ...more

Banana to alligator for testing capacitors, inductors and resistors. Length - 12" ...more

DC Bias Current Source (or DC Magnetization Current Source), is mainly used for inductance measurement of inductors and transformer windings with DC bias current. Except for constant current output, low additional error and wide frequency response range are important for bias current inductance measurement. ...more

DC Bias Current Source (or DC Magnetization Current Source) used for inductance measurement of inductors and transformer windings with DC bias current. Except for constant current output, low additional error and wide frequency response range are important for bias current inductance measurement. ...more

DC constant current source, is used for low frequency DC current biased impedance measurement of inductors, transformers and coils. The inductance characters under specified bias current can be measured and evaluated. ...more

TEGAM's Models 252, 253, and 254 are equivalent to ESI 252, 253, and 254. Perfect for component inspectors or manufacturing operators performing manual testing of inductors, capacitors, or resistors. An optional limits comparator is available for sorting components according to their measured parameters. ...more

Easiest and Accurate Quality control of filters and its components, Inductors & Capacitors ...more

RLC measurement is one of the many uses of the Venable Frequency Response Analysis System (see Products page). This function can be greatly enhanced by adding the RLC Measurement Package to provide an accurate, easily-used instrument for measuring values of resistors, inductors, and capacitors. It can also be used to measure values of one or t ...more